Deramp Altair 8800c Manual de usuario

Page 1

Altair 8800c Front Panel Board Set

Ver 1.2, Feb 2019

Introduction

The Altair 8800c front panel

board set is a drop-in re-

placement for the original Al-

tair 8800 front panel board.

The ne board set as creat-

ed for the follo ing reasons:

1) Availability

Finding an original front panel board to restore

or build an Altair is nearly impossible. The ne

board set provides a drop-in equivalent that is

readily available.

2) Elimination of the Hand Wired Harness

The original front panel board picked up bus sig-

nals and connected to the CPU board through a

large hand- ired harness. This harness as te-

dious to build and as often a reliability issue –

especially if you had to remove and ork on the

front panel board. The 8800c board set replaces

the hand- ired harness ith a 50 pin ribbon ca-

ble that connects to a bus interface board (sho n here) to pick up and drive the required bus signals.

3) Mechanical Compatibility with the Altair 8800 Clone Cabinet

The original Altair 8800 cabinet made by Optima is no longer manufactured, and like the original

front panel board, finding an original cabinet by itself is nearly impossible. As an alternative, the cab-

inet for the Altair 8800 Clone is still available, ho ever, the original front panel board covers mount-

ing points in the Clone cabinet’s front panel bracket. This ne front panel board is designed to fit

properly in the Clone cabinet’s mounting bracket. The ne front panel board also fits in an original

Altair cabinet.

4) Compatible with the 8800b CPU Board

The original front panel board does not ork ith an Altair 8800b CPU board and vice-versa. This is

due to a change in ho the 8800b front panel injects data into the CPU and ho it stops the CPU. For

increased flexibility, the ne front panel set orks ith both the original and the 8800b CPU boards.

5) Logic Error Fixes

The original front panel board had a fe logic problems that are fixed in the ne front panel board

set. These same problems ere also fixed by MITS hen they designed the 8800b computer.

CPU “Stop” Timing Error

The Stop s itch is designed to put the 8080 into a ait state on an instruction fetch bounda-

ry (the M1 cycle). Ho ever, due to a timing issue in the run/stop circuit, the front panel

doesn’t al ays stop on an M1 cycle.

Page 2

Indeterminate Power On State

On po er-on, the run/stop flip-flop on the front panel board is not initialized and the 8080

processor is not given a reset signal. These omissions tend to leave the 8080 in an invalid

state on po er-on. This is hy the “STOP/RESET” s itch sequence is required to put the

computer into a valid state. This fix can be optionally enabled or left like the original.

Reset not Synchronized with phi2

An undocumented 8080 reset timing requirement is that reset be released a minimum of

about 200ns prior to the rising edge of phi2. This is implemented in the Intel 8224 clock gen-

erator that as used on the 8800b CPU board, but this chip is not used on the original Altair

CPU board. The ne front panel board enforces this timing for resets generated by the front

panel.

Front Panel PRDY Output is not Open Collector

Clients on the bus should drive the PRDY signal ith an open collector driver. The signal is

terminated on the CPU board ith a 1K pull-up resistor. Ho ever, the original front panel

board actively drives this signal high. Therefore, hen any bus client drives PRDY lo to in-

sert ait states, its output driver is sinking the active high drive of the front panel’s PRDY

driver.

6) Enhancements

In addition to duplicating the functionality of the original front panel board, the 8800c front panel

board set offers several enhancements that can be optionally enabled:

• An output latch at I/O address 0FFh that can display on the data LEDs (similar to IMSAI 8080)

• Auto repeat single-step at selectable rate from 1hz-8hz, similar to the 8800b

• Code snippet injection: Common Altair bootstrap loaders, port echo routines, Kill-the-Bit, etc.

can be injected into RAM by selecting the desired code snippet on the lo er eight address

s itches, then depressing the AUX-Left s itch.

• Auto jump on po er-on (can be independent of reset operation)

• Auto jump on reset (can be independent of po er-on operation)

Page 3

Front Panel Board Assembly

Assembly of the front panel board is not a beginner’s project and these instructions on’t teach you

ho to solder components on a PCB, solder connectors, or sho you the difference bet een a resistor

and a diode. If you have any concerns about building this board, please contact me first.

Many assembly details are illustrated in photographs that follo . Rather than print this manual, you

may ant to vie this document on your tablet hile you ork. A tablet makes it especially easy to

zoom into the photos to see the details you may need.

Parts List

Designator Description Part Number Distributor

C1-C5 0.1uf, 50v 2146302 Jameco

C6 100uf, 16v electrolytic 647-TVX1C101MAD Mouser

D1-D36 Red LED Everlite HLMPD150A Digi-Key 1080-1064-ND

J1 50 pin, dual ro IDC straight header 517-D3433-6302-AR Mouser

J2 5-pin, 0.156 locking header B5P-VH-B-LFSN Digi-Key 455-1642-ND

Female Housing VHR-5N Digi-Key 455-1186-ND

Crimp Pins SVH-21T-P1.1 Digi-Key 455-1133-1-ND

IC-A,B,C,D,E 74LS165 Parallel In Shift Register 595-SN74LS165AN Mouser

R1-R36 2K, 1/4 , 5% 291-2K-RC Mouser

R37-R52 4.3K,1/4 , 5% 291-4.3K-RC Mouser

S1 Toggle S itch On-None-On (Silver) APEM 5236AB Search for best deal

S10-S25 Toggle S itch On-None-On (Gold) APEM 5236CDB Search for best deal

S2-S9 Toggle S itch (On)-Off-(On) (Gold) APEM 5237CDB Search for best deal

Switches

If at all possible, do not use C&K switches for the front panel. The C&K s itches have an erratic and stiff

feel – especially the momentary s itches – compared to the American S itch brand used in the original

Altair. In addition, I’ve had several C&K s itches break hile gently tightening the bushing nut as ell as

during normal use. The APEM s itch part numbers listed above are much closer to the original American

S itch brand. In fact, APEM purchased American S itch a number of years ago.

The po er s itch must have silver contacts as noted for S1. Ideally, use gold contacts for all remaining

s itches. Do not mix s itch brands as most have slightly different body heights and this causes prob-

lems hen mounting the front panel to the mounting plate/bracket.

The APEM s itches can be expensive. I may be able to help ith a bulk buy. Contact me if interested.

Additional Part Notes

Use only LS-TTL parts. Some IC inputs are tied directly to Vcc. Multi-emitter TTL inputs do not tolerate

this ell (e.g., 74xxx and 74Sxxx).

The specified LEDs provide an appropriate brightness ith the 2K resistors specified for R1-R36. You may

need to choose a different resistor value if a different LED is used.

Page 4

Front Panel Assembly Steps

First, insert and solder lo -profile parts

1) Insert and solder R1-R52.

2) Insert and solder IC-A through IC-E (or sockets).

3) Insert and solder C1-C6. Note polarity on C6.

The follo ing instructions for installation of the s itches and LEDs assume you have an Altair Clone cab-

inet. If you’re installing in an original Altair cabinet, follo the instructions in the original manual for me-

chanically aligning the s itches and LEDs hile soldering into the PCB.

Use the front panel mounting bracket from the Altair Clone cabinet as a jig to help install the front panel

s itches, S1 through S25. Do not attempt to solder the switches without usin a ji .

Note: The follo ing pictures are from the Altair Clone assembly manual, so the PCB looks a bit different

than the 8800c front panel board. I nore the LED orientation/polarity shown in the pictures.

1) Prop the front panel bracket an inch or t o above your ork surface and orient the bracket as

sho n in the picture belo . Note, the APEM switches are blue, not red as show in the picture.

2) Place the po er s itch, S1 (toggle s itch ith silver terminals) in the bracket (far left corner as

pictured). Notice that each s itch has a slot in the threaded bushing. Orient the slot of all s itches

a ay from your vie as you place them in the bracket.

3) Place S2-S9 (momentary s itches ith gold terminals) in the eight holes across the bottom of the

bracket (ro furthest a ay from your vie ). Again, orient the slot of all s itches a ay from your

vie as you place them in the bracket.

4) Place S10-S25 (toggle s itches ith gold terminals) in the 16 holes above the eight momentary

s itches. Again, orient the slot of all s itches a ay from your vie .

Page 5

5) Check that all s itches are as squarely aligned as possible, then carefully lo er the circuit board,

component side do n, onto the s itches. Don’t let o of the board after you have it settled on

the s itches as the board ill tend to rock to ards you and fall off the s itches.

6) To solder the s itches, keep pressure on the board ith your “spare” fingers placed in bet een

the t o ro s of s itches and near here you are soldering. This keeps the board level and square

on the s itches.

The next step is to install the front panel LEDs. In order to hold the LEDs at the proper and consistent

height above the board, use the front

dress panel as a jig. Do not cut or prep LED

leads until after soldering is complete!

1) Insert D1-D36 fully into the circuit

board. The anode of the LED is indi-

cated by the longer lead and the

cathode by the flat spot on flange

(for the specific LED in the parts list).

The cathode is closer to the top side

of the circuit board and the anode is

closer to the bottom of the circuit

board. You may ant to prop the

PCB off the ork surface as sho n

to accommodate the long LED leads.

Page 6

2) Work the front dress panel over the s itches and then do n the s itch bushings slightly. You

don’t need to push the panel all the ay do n to the s itch body.

3) Turn the PCB/front panel over as sho n belo and let the LEDs fall into the front panel LED holes.

If the front panel sags a bit in the middle, add a third support point near the middle of the panel.

4) Carefully adjust the spacing bet een the PCB and the front panel in order to accommodate the

four 5/8” spacers provided*. The goal is to make the PCB and front panel as parallel as possible.

The spacers are used only for this step – they do not remain in the assembly. (Note that once an

LED is soldered, it can then serve as a “spacer”) See the pictures on the next pa e.

5) Push each LED all the ay do n into its corresponding front panel hole. Re-verify that the front

panel and PCB look perfectly parallel to each other and are resting directly on all of the hite

spacers. See the pictures on the next pa e.

6) Solder the LEDs: Press do n gently on the PCB ith your “spare” fingers as you solder the LEDs to

the PCB. You may ant to slide the hite spacers near the area you are orking as you proceed

through the LEDs. Note that once an LED is soldered, it can then serve as a “spacer.”

* The spacer height determines ho far the LEDs ill protrude through the front panel after final as-

sembly. With APEM s itches in the Altair Clone case, a spacer height of 5/8” to 11/16” gives a good

LED position after final assembly. At 5/8”, the LEDs protrude just slightly through the front panel. At

11/16”, the LEDs protrude a bit further. You can add something thin under each 5/8” spacer to raise it

to ards 11/16” depending on your LED position preference. The spacin requirement is different if

you use a different s itch brand since s itch body height varies slightly bet een brands.

Page 7

Lastly, install J1 and J2 on the back side of the circuit board.

J1 – Note the orientation of the keying slot before soldering the connector onto the board. Again, the

connector goes on the back side of the board.

J2 – Though not a requirement, I’d recommend pulling the center pin out of the J2 connector. If you

leave the pin in place, note that its hole on the PCB is not plated and should not be soldered.

Page 8

Final Assembly (using an Altair Clone cabinet)

Mount the circuit board to the front panel support bracket.

1) Set all toggle s itches in the

do n position. Feed the

s itch batons into the holes

through the rear of the sup-

port bracket. Be sure the

bracket is fully seated

against the body of every

s itch. You may have to

squeeze/push the panel

firmly around a fe of the

s itches to free those spots

here the support bracket

may be caught on the

s itch threads.

2) Install a lock asher and nut (finger tighten only) on the po er s itch, all eight momentary

s itches, and every other address s itch (A14, A12, A10,… do n to A0) as highlighted belo .

3) Incrementally tighten nuts – one on the far left, then one on the far right, orking back to the

middle, then repeat tightening each nut a bit more. A 5/16” deep socket makes this job much

easier. Do not over-tighten the nuts – trust the lock asher.

Page 9

Mount the front dress panel to the front panel sup-

port bracket.

1) Slide a 0.150 hite spacer over each of the six

studs on the back of the front dress panel.

2) Insert the batons from the s itches into the

front panel and ork the studs into the holes on

the front panel support bracket until the front

panel and support bracket have fully sand-

iched the spacers.

3) Work the front panel do n around the s itch

bushings as needed until the front panel is flat

and even over all 25 s itches. When properly

assembled, the bushings generally protrude just

slightly above the surface of the front panel.

4) Install a #6 nut over each of the studs on the back side of the support bracket(do not tighten). A

shallo 5/16” nut driver makes this job easier.

5) Incrementally tighten the nuts – one on the far left, then one on the far right, orking back to the

middle, then repeat tightening each nut a bit more.

Page 10

Install the Front Panel Assembly into the Case.

1) Slide the front panel assembly in from the front of the case. The front panel may be snug as it goes

into the case bezel. If this is the case, ork the panel in bit-by-bit, keeping the amount of insertion

on all four sides approximately equal as you ork the panel back ards into place ( here the

mounting bracket’s threaded holes line up ith the four holes in the bottom of the case).

2) Attach the front panel support bracket using four of the #6 scre s you set aside during disassem-

bly of the case. Lock ashers go under the t o scre s closest to the rear the panel. The

lock ashers ensure an electrical connection bet een the chassis and the front mounting bracket

for better static protection.

Tabla de contenidos

Manuales populares de De oficina de otras marcas

HP m9060n - Pavilion - Elite Hoja de especificaciones

Asus

Asus E210 Series Manual de usuario

Dell

Dell Inspiron 600m Manual de usuario

Dell

Dell Inspiron 3662 Manual de usuario

TotalFlow

TotalFlow uFLO Manual de usuario

HP Presario SV7000 - Desktop PC Manual de usuario

HP ProDesk 400 G5 Manual

Logitech

Logitech MK320 Manual de usuario

Dell

Dell XPS 730 H2C Manual de usuario

Sony

Sony Vaio Series Manual de usuario

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manual de usuario

Alto

Alto MD 250 Manual de usuario

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series Manual de usuario

Sony

Sony VAIO VGX-TP1 Series Manual de usuario

Asus

Asus Eee Box B204 Manual de usuario

Dell

Dell Optiplex 9010 All In One Manual de usuario