Denver SWC-363 Manual de usuario
SWC-363
denver.eu
À DÉPOSER
EN MAGASIN À DÉPOSER
EN DÉCHÈTERIE
OU
FRFR
Cet appareil et
ses accessoires
sont recyclables
06/22
Caution: When the first time you use the fitness tracker,
please make sure to fully charge it before using. Please
read this user guide carefully before using the product.
It contains important information for your safety as well
as use and maintenance advice. Keep this user guide for
future reference.
Getting Started
ENG-1
The product contains electrical components that could
cause injury if not handled properly.
·Do not open the enclosure or disassemble the product.
·Do not expose the product to extremely high or low
temperatures.
·Do not use the product in a sauna or steam room.
·Do not leave the product in direct sunlight for an
extended period of time.
·Do not dispose the product in a fire, the built-in battery
can explode.
·The product features a built-in battery, which is not user
replaceable.
·Do not check call notifications or other data on the
product's screen while driving or in other situations
where distractions could be hazardous.
·The distance travelled may be inaccurate. It is for
reference only and should not be used as any
navigational reference.
·The product should usually rest a finger's width below
the wrist bone, as you would normally wear a bracelet.
·This product has been classified as lP67 daily waterproof.
Safety Precautions
ENG-2
Caution: The device may cause skin irritation. Prolonged
contact may contribute to skin irritation or allergies in
some users. If you notice any signs of skin redness,
swelling, itchiness or other skin irritation, please
discontinue using the product. Continued use, even after
symptoms subside, may result in renewed or increased
irritation. If symptoms persist, consult your doctor. Do
not open the enclosure or disassemble the product.
Blood Oxygen Notice
·WARNING! Only a medical practitioner is qualified to
interpret your blood oxygen measurements. The use of
this smart bracelet should not replace regular medical
examinations.
·Blood Oxygen can be subjected to wide fluctuations in
a short period of time. Its level depends on many factors.
·Different medicines, alcohol and smoking can exert a
large influence on the level of Blood Oxygen. Do not
smoke, drink caffeinated beverages or exercise within
the 30 minutes before measuring your blood oxygen.
Intended Use
This smart bracelet is intended for monitoring fitness-
related metrics such as heart rate, blood pressure,
distance walked or run, calorie consumption and quality
of sleep. Data measured should not be used for any
medical, ambulatory or dietary reference.
Product Overview
Power-on
Press and hold the side button for 3 seconds or plug in
the magnetic charging cable to charge the smart watch.
ENG-3
Charging
contacts
Heart rate
monitor
Download and connect with
smart watch App
1. Download and install App.
· Scan the QR code with your phone to download the
App.
· iOS system: search and download “Da Fit” from App
Store.
· Android system: search and download “Da Fit” from
Google Play.
Da Fit
Note: your mobile phone must support Android 5.1 or
IOS 8.0 or above, and Bluetooth 4.0 or above.
ENG-4
2. Connect smart watch with App.
1.Click "Add Device" to
find the smart watch.
ENG-5
2.Click on your device in
the device list scanned.
SWC-363
3. The iOS system will
show a Bluetooth pairing
request and you can click
"Pair" to confirm.
Android system connects
with your watch directly.
SWC-363
“SWC-363”would like to pair with
your iPhone.
Bluetooth Pairing Request
4.Successfully bound.
ENG-6
SWC-363
Bluetooth call connection
Android phone:
1. After the App successfully connects to the watch's
Bluetooth, your phone will automatically pop up a
"pairing" request, click "Allow".
2. Some mobile phone models don’t need a pairing
confirmation. After connecting the watch with App,
the Bluetooth connection for call function is also
established. Then you can answer and make calls on
the watch.
iOS phone: Go to Settings > Bluetooth, search for the
device SWC-363 and pair with it. After the devices are
connected successfully, you can make and answer calls
from your watch.
Remove Bluetooth call connection
Android phone: The device can be disconnected from
your mobile phone by simply clicking on “Remove device”.
iOS phone: Go to Settings > Bluetooth, select SWC-363,
then click “Forget This Device”, your watch and mobile
phone are now disconnected.
ENG-7
Smart watch functions
Swipe the touchscreen to switch the menu interface
and access the various features of the watch. The
interfaces are shown below:
ENG-8
Remove the device
For Android phones, the device can be disconnected
from your mobile phone by simply clicking “Remove
device”.
For iOS phones, after binding removal from the App, go
to Settings > Bluetooth, then click “Forget This Device”.
ENG-9
SWC-363
12
Otros manuales para SWC-363
1
Tabla de contenidos
Otros manuales de Mirar de Denver
Denver
Denver SW-360 Manual de usuario
Denver
Denver SW-170 Manual de usuario
Denver
Denver SW-164 Manual de usuario
Denver
Denver SW-151MK2 Manual de usuario
Denver
Denver SW-170 Manual de usuario
Denver
Denver SW-350 Manual de usuario
Denver
Denver SW-181 Manual de usuario
Denver
Denver SW-151 Manual de usuario
Denver
Denver SW-160 Manual de usuario
Denver
Denver BFH-17 Manual de usuario
Denver
Denver SW-450 Manual de usuario
Denver
Denver SWC-372 Manual de usuario
Denver
Denver SMARTWATCH SW-163 Manual de usuario
Denver
Denver BFH-150 Manual de usuario
Denver
Denver SW-171 Manual de usuario
Denver
Denver SW-160 Manual de usuario
Denver
Denver SW-500 Manual de usuario
Denver
Denver BFH-252 Manual de usuario
Denver
Denver SW-510 Manual de usuario
Denver
Denver SW-170 Manual de usuario
