Denver MMP-355 Manual de usuario

1. Power Button

2. Band Switch

3. Function Switch

(AUX/CD/TAPE/RADIO)

4. Bass Boost Button

5. CD Mode Button

6. CD Program Button

7. CD Stop Button

8. CD Play/Pause Button

9. CD Skip/Search Forward

Button 

10. CD Skip/Search Backward

Button 

11. Volume Control Knob

12. Tuning Knob

13. Dial Pointer

14. CD LCD Display

15. Remote Sensor

16. Power/Standby LED Indicator

17. FM Stereo LED Indicator

18. Radio Functional Indicator

19. Tape Functional Indicator

20. CD Functional Indicator

21. Cassette Compartment

22. Aux Jack

23. Cassette Record Button

24. Cassette Play Button

25. Cassette Rewind Button

26. Cassette Fast Forward Button

27. Cassette Stop/Eject Button

28. Cassette Pause Button

29. Stereo Headphone Jack

30. Cassette Key Control Door

31. Speaker Terminal (L/R)

32. AC Power Cord

33. FM Antenna

34. CD Door

35. Speaker Box Left

36. Speaker Box Right

37. Folder Down Button “-”

38. Folder Up Button “+”

English - 1

AC OPERATION

Before operating, please check carefully that the voltage indicated on your

set corresponds to the voltage of your local area.

1. Plug the AC POWER CORD into a standard AC outlet.

2. Press the POWER BUTTON to start the unit.

POWER/STANDBY LED INDICATOR will light up to indicate unit is

connected to the power source properly.

SPEAKER BOX CONNECTION

Insert the Speaker plug of the SPEAKER BOXES to the SPEAKER TERMINAL

on the rear of the unit.

RADIO OPERATION

1. Slide the FUNCTION SWITCH to the “RADIO” position, the RADIO

FUNCTIONAL INDICATOR will light up.

2. Slide the BAND SWITCH to the desired waveband.

3. Turn the TUNING KNOB to your desired radio station.

4. Adjust the sound level by pressing the VOLUME CONTROL KNOB Up or

Down.

5. To turn off the radio, press the POWER BUTTON to “OFF” position.

FM STEREO INDICATOR

When tuned to a FM stereo broadcast the “FM ST” INDICATOR will light up.

If it does not, check that the BAND SWTICH is set to “FM ST” position. In

weak signal areas the FM stereo signal may not be strong enough and can

cause excessive background noise. In this case, slide the BAND SWITCH to

the “FM” position.

ANTENNAS

For best reception, fully extend the FM ANTENNA to receive FM stations. For

AM reception, the unit has a built-in antenna, and it may be necessary to turn

the whole unit for best reception.

BASS BOOST

At all volume levels, push the BASS BOOST BUTTON to “ON” position to

enhance the low frequency sound. To release the super bass, simply push

this button once again.

STEREO HEADPHONE JACK

For private listening, insert the plug of a Stereo Headphone into the STEREO

HEADPHONE JACK and adjust the VOLUME CONTROL KNOB accordingly. Be

English - 2

sure that your headphone has 3.5mm diameter stereo plug with an

impedance of 32 ohms. During the use of a headphone, the Speakers are

automatically disconnected.

Cassette operation

Tape Playback

First of all, open the CASSETTE KEY CONTROL DOOR (30)

1. Press the STOP/EJECT BUTTON to open the cassette door.

2. Insert a pre-recorded cassette tape into the CASSETTE COMPARTMENT

and close the cassette door.

3. Slide the FUNCTION SWITCH to the TAPE position, the TAPE

FUNCTIONAL INDICATOR will light up.

4. Press the PLAY BUTTON.

5. Adjust the VOLUME CONTROL KNOB to your desired listening level.

6. To stop the tape, press the STOP/EJECT BUTTON.

7. To turn off the unit, press the POWER BUTTON to “OFF” position.

Fast Forward and Rewind

The tape can be fast forwarded or rewound by pressing the FAST FORWARD

BUTTON or REWIND BUTTON respectively.

Pause Function

During playback or recording, the tape can be stopped temporarily by

pressing the PAUSE BUTTON. To continue playback or recording, press the

PAUSE BUTTON again.

Auto Stop System

When the tape runs to the end during playback or recording, the cassette

operation will be stopped automatically.

Note : When fast forwarding or rewinding, the STOP BUTTON must be

pressed when the tape runs to the end.

Caution

To avoid damage to the cassette mechanism or to the cassette tapes, always

press the STOP/EJECT BUTTON between each operation!

Recording From The Radio

1. Tune to a desired radio program as described in the “RADIO OPERATION”

section.

2. Insert a blank cassette tape into the CASSETTE COMPARTMENT.

3. Press the PAUSE BUTTON.

English - 3

4. Press the RECORD BUTTON. The PLAY BUTTON is engaged

simultaneously to start recording. With the built-in Automatic Level

Control (ALC), the best recording quality is automatically adjusted.

Changing the volume level will not affect the recording. Release the

PAUSE BUTTON to begin recording.

5. To stop recording temporarily, press the PAUSE BUTTON. To continue the

recording, press the PAUSE BUTTON once again.

6. Press the STOP/EJECT BUTTON to stop recording.

7. When the tape runs to its end, the cassette operation will be stopped

automatically.

CD OPERATION

PLAYING COMPACT DISC (CD-R/RW PLAYBACK COMPATIBLE)

Getting Started

Note: Should skipping of tracks occur during CD playing, try turning the

volume down.

When CD is playing, do not open the CD DOOR.

1. Open the CD DOOR by pull up the CD DOOR. Put a CD disc into the CD

Compartment and close the CD DOOR. Set the FUNCTION SWITCH to

“CD” position, the CD LCD DISPLAY and CD FUNCTIONAL INDICATOR

will light up.

Note : Ensure the CD DOOR is closed properly

and locked in place.

2. When the CD DOOR is closed with a CD inside,

total number of the tracks in the disc will be shown

on the CD LCD DISPLAY and will go to stop mode.

(ex. Total 17 tracks inside the disc).

3. If there is no disc inside, the LCD DISPLAY will

show “ ” and go to stop mode.

4. If the CD DOOR is not closed, the DISPLAY will

show “ ”.

Play/Pause Mode

1. When the PLAY/PAUSE BUTTON is pressed during

CD stop mode, the first track will be played. The

Play Indicator “” will be shown on the LCD

DISPLAY. The CD LCD DISPLAY will show the

English - 4

specific number of track being played.

2. For interruption while the CD is playing, press the CD PLAY/PAUSE

BUTTON once. The Play Indicator “” will blink continuously on the LCD

DISPLAY.

3. Though the sound stops, the disc will continue to

spin. To re-start playing, press the CD PLAY/PAUSE

BUTTON once again. The music will start from the

exact position where it was interrupted.

4. To stop the CD, press the CD STOP BUTTON once

whether the CD is in Play or Pause mode. The LCD

DISPLAY will show the total number of tracks of the disc again.

5. To turn off the unit, press the POWER BUTTON to “OFF” position.

Skip And Search Mode

1. During play or pause mode, when CD SKIP/SEARCH or CD

SKIP/SEARCH BUTTON is pressed once, it will go to the next track or

go back to the beginning of the track.

2. During play mode, when CD SKIP/SEARCH or CD SKIP/SEARCH 

BUTTON is pressed and held, it will search the track with audible high-

speed forward or backward playback.

Repeat Mode

1. Repeat 1 :

When the MODE BUTTON is pressed once, the

Repeat Indicator “ ” will be shown on the LCD

DISPLAY. This single track of music will be

repeated.

2. Repeat All:

When the MODE BUTTON is pressed twice, the

Repeat All Indicator “ ” will be shown on the

LCD DISPLAY. The whole disc can be played

continuously.

3. To cancel the Repeat Function

Press the MODE BUTTON repeatedly until the

Repeat Indicator disappears from the LCD DISPLAY.

Random Play Mode

This feature allows the track on the disc to be played

in a random order.

1. During the CD stop mode, press the MODE

BUTTON three times, the “ ” indicator will

English - 5

be shown on the LCD DISPLAY. Press the PLAY BUTTON once to start the

playback.

2. To cancel the random play function, press the MODE BUTTON again,

“” Indicator will disappear from the LCD DISPLAY.

Program Mode

1. During the CD stop mode, press the PROGRAM BUTTON once. The

Program Indicator “ ” and the number of Program to be memorized

starts from the first program “ ” will light up

and blink continuously.

Press the CD SKIP/SEARCH or SKIP/SEARCH 

BUTTON to your desired musical track, the CD LCD

DISPLAY will show the appropriate track number.

Press the PROGRAM BUTTON to store this track in memory.

2. Repeat above procedure until all desired tracks have been programmed.

A total of 20 tracks can be stored in memory.

Remarks :

Whenever CD SKIP/SEARCH FORWARD or

BACKWARD BUTTON is pressed, it will always show

the last programmed track first to recall your

memory.

After complete programming, LCD DISPLAY will show “ ” and

flash continuously.

3. Press the CD PLAY/PAUSE BUTTON once to start

the program playback and the CD Play Indicator

“” will light up.

4. To check the program you have stored after

complete programming, press the PROGRAM BUTTON once during CD

stop mode, then press the CD SKIP/SEARCH FORWARD BUTTON once,

the LCD DISPLAY will show the first programmed track number. Repeat

above procedure to read all the programmed memory.

5. To cancel the programmed memory :

¾During the CD stop mode, press the CD STOP BUTTON once.

¾Open the CD DOOR during the CD stop mode.

The Program Indicator “ ” will disappear from the LCD DISPLAY.

English - 6

PLAYING MP3 DISC

Getting Started

Note: Should skipping of tracks occur during MP3 Disc playing, try turning

the volume down.

When MP3 disc is playing, do not open the CD DOOR.

1. Open the CD DOOR by pull up the CD DOOR. Put a MP3 disc into the CD

compartment and close the CD DOOR. Set the FUNCTION SWITCH to

“CD” position, the CD LCD DISPLAY and CD FUNCTIONAL INDICATOR will

light up.

Note : Ensure the CD DOOR is closed properly and locked in place.

2. When the CD DOOR is closed with a MP3 disc inside,

total number of the tracks in the disc will be shown

on the CD LCD DISPLAY and go to stop mode.

3. If there is no disc inside, the DISPLAY will show

“” and go to stop mode.

4. If the CD DOOR is not closed, the DISPLAY will

show “ ”.

Play/Pause Mode

1. When the PLAY/PAUSE BUTTON is pressed during CD stop mode, the first

track will be played. The Play Indicator “”will be

lighted. The “ ” Indicator will be shown as well

to indicate MP3 Disc is being played. The LCD

DISPLAY will show the specific track number being

played.

2. To select the specific musical tracks inside the MP3 Disc.

MP3 music can be stored into CD Disc with or without folders according to

your “MP3 burning method”.

a. If the MP3 disc is

downloaded without

dividing into folder, all

track number will be

shown directly in the

LCD DISPLAY. The

Album number will only

show after pressing the FOLDER UP or DOWN BUTTON.

b. If the music is stored into different folders, then you’ve to select the

specific Album number first by pressing the FOLDER UP or DOWN

BUTTON ; afterwards press the CD SKIP/SEARCH FORWARD or

BACKWARD BUTTON to select the specific Track number music inside

this Album.

English - 7

Example : To select Album # 4, track # 3.

STEP – 1 : Press the FOLDER UP or DOWN

BUTTON to select the Album # 4.

STEP – 2 : Press the CD SKIP/SEARCH

FORWARD or BACKWARD BUTTON

to select the Track # 3 inside this

Album # 4.

3. For interruption while MP3 disc is playing, press the CD PLAY/PAUSE

BUTTON once. The Play Indicator “” will blink continuously on the LCD

DISPLAY.

4. Though the sound stops, the disc will continue to spin. To re-start playing,

press the CD PLAY/PAUSE BUTTON once again. The music will start from

the exact position where it was interrupted.

5. To stop the MP3 disc, press the CD STOP BUTTON once whether the MP3

disc is in Play or Pause mode.

6. To turn off the unit, press the POWER BUTTON TO “OFF” position.

Repeat Mode

1. Repeat 1 :

When the MODE BUTTON is pressed once, the

Repeat Indicator “ ” will light. This single track

of music will be repeated.

2. Repeat Folder :

When the MODE BUTTON is pressed twice, the

“” and “ ” indicator will be shown. This

specific folder will be played repeatedly.

3. Repeat All :

When the REPEAT BUTTON is pressed three times,

the Repeat All Indicator “ ” will be shown. The

whole disc can be played continuously.

4. To cancel the Repeat Function

Press the MODE BUTTON repeatedly until the Repeat Indicator

disappears from the LCD DISPLAY.

English - 8

Random Play Mode

This feature allows the tracks on the disc to be played in a random order.

1. During the CD Stop mode, press the MODE

BUTTON four times, the “ ” Indicator will

show on the LCD DISPLAY. Press the PLAY/PAUSE

BUTTON once to start the playback.

2. To cancel the Random Play function, press the

MODE BUTTON again, “ ” Indicator will disappear from the LCD

DISPLAY.

Skip And Search

1. During play or pause mode, when CD SKIP/SEARCH or CD

SKIP/SEARCH BUTTON is pressed once, it will go to the next track or

go back to the beginning of the track.

2. During play mode, when CD SKIP/SEARCH or CD SKIP/SEARCH 

BUTTON is pressed once and held, it will search the track with audible

high speed forward or backward playback.

Program Mode

1. During the CD stop mode, press the PROGRAM BUTTON once. The

Program Indicator “ ” and the number of

Program to be memorized starts from the first

program “ ” will light up and blink continuously.

Press the FOLDER UP or DOWN BUTTON, then

press CD SKIP/SEARCH FORWARD or BACKWARD

BUTTON to select your desired musical track, CD LCD DISPLAY will show

the track number of this specific Album to be programmed. Press the

PROGRAM BUTTON to store this track in memory.

2. Repeat above procedure until all desired tracks have been programmed.

Remarks : Whenever the FOLDER UP or DOWN BUTTON is pressed, it

will always show the last programmed Album number first

to recall your memory.

A total of 10 tracks can be stored in memory. After complete

programming, LCD DISPLAY will show “ ” and blink

continuously.

3. To start the Programmed playback, press the CD PLAY/PAUSE BUTTON

once and the CD Play Indicator “”, “ ” and the track number of

the specific Album will light up.

English - 9

Example : Album # 3, Track # 2.

4. To check the program you have stored after complete programming,

press the PROGRAM BUTTON once during the CD Stop mode. The LCD

DISPLAY will show “ ” and blink continuously. Press the FOLDER UP

or DOWN BUTTON to read the Album number, then press the CD

SKIP/SEARCH FORWARD or BACKWARD BUTTON to read the specific

track number of said Album. Press the PROGRAM BUTTON again, LCD

DISPLAY will show “ ” and blink continuously. Repeat above

procedure to check all programs being stored.

5. To cancel the programmed memory :

¾During the CD stop mode, press the CD STOP BUTTON once.

¾Open the CD Door during the CD stop mode.

The Program Indicator “ ” will disappear from the LCD DISPLAY.

Recording From CD Player

1. Slide the FUNCTION SWITCH to “CD” position, the CD LCD DISPLAY and

CD FUNCTIONAL INDICATOR will light up.

2. Put a CD into the CD compartment with the label side upward.

3. Insert a cassette into the cassette compartment and press PAUSE

BUTTON of the cassette deck.

4. Press RECORD BUTTON and PLAY BUTTON simultaneously for recording

stand-by. With the built-in ALC, the best recording quality is adjusted

automatically.

5. Activate the CD player, playing in a desired track as described in the

COMPACT DISC PLAYER OPERATION section. Release the PAUSE

BUTTON of the cassette deck to start recording.

6. To stop recording temporarily, press the PAUSE BUTTON. To continue

recording, press the PAUSE BUTTON again.

7. Press STOP/EJECT BUTTON of the cassette deck to stop recording. Then

stop CD playback by pressing the CD STOP BUTTON of the CD player.

English - 10

Tabla de contenidos

Otros manuales de Sistema estéreo de Denver

Denver

Denver MCB-700 Manual de usuario

Denver

Denver MDA-260 Manual de usuario

Denver

Denver MRP-141 Manual de usuario

Denver

Denver MMP 351 Manual de usuario

Denver

Denver MCA-171 Manual de usuario

Denver

Denver MC-5230DAB+ Manual de usuario

Denver

Denver MCU-5301 Manual de usuario

Denver

Denver MDA-270 Manual de usuario

Denver

Denver MDA-240 Manual de usuario

Denver

Denver MRP-151 Manual de usuario

Denver

Denver MCB-600 Manual de usuario

Denver

Denver MCA-210 Guía del usuario

Denver

Denver MCA-54 Manual de usuario

Denver

Denver MC-7100S Manual de usuario

Denver

Denver MC-7150 Manual de usuario

Denver

Denver MCD-63 Manual de usuario

Denver

Denver MC-5230DAB+ Manual de usuario

Denver

Denver MMP-360 Manual de usuario

Denver

Denver MCI-102 Manual de usuario

Denver

Denver MCI-103 Manual de usuario

Denver

Denver MRP-161 Manual de usuario

Denver

Denver MCA-190 Manual de usuario

Denver

Denver MCI-101 Manual de usuario

Denver

Denver MC-5400 Manual de usuario

Manuales populares de Sistema estéreo de otras marcas

LG CM3330B Manual de usuario

Sony

Sony SS-CEP50 Manual de usuario

Cetacea Sound

Cetacea Sound CVS-II Manual de usuario

Aiwa

Aiwa XR-H66MD Manual de usuario

Denon

Denon UCD-250 Manual de usuario

Sanyo

Sanyo DC-MX41i Manual de usuario

Sharp

Sharp CD-ES600V Manual de usuario

Exibel

Exibel BDX600-UK Manual de usuario

Sanyo

Sanyo DC-F320 Manual de usuario

Philips

Philips FWM583X Manual de usuario

Sharp

Sharp CD-C462 Manual de usuario

Onkyo

Onkyo CBX 300 - CD / MP3 Clock Radio Manual de usuario

Aiwa

Aiwa XR-EM70 Manual de usuario

Cyrus

Cyrus Lyric Manual de usuario

Philips

Philips MCM159/98 Manual de usuario

Philips/Magnavox

Philips/Magnavox Magnavox FW 62C Manual de usuario

RCA

RCA RS3965SB Manual de usuario

Sharp

Sharp XL-UH240 Manual de usuario