10 11
OPERATION INSTRUCTIONS
8°C HEAT MODE
HOW TO SET THE 8°C HEATING
Press the 8°C HEAT button at the heating mode.
In 8°C HEAT mode, the fan speed is set at “AUTO”
automatically.
The 8°C HEAT mode will be started when you
press 8°C HEAT button at the heating mode.
If you press any button except for iFEEL,
TIMER ON, TIMER OFF, CLOCK, SWING and
escape from 8°C HEAT mode. Then the display
will disappear and the 8°C HEATING mode will
be cancelled.
NOTE: In 8°C HEATING mode, the default
temperature is set
46°F/8°C
.
8°C HEATING mode can be set only when the
air conditioner works in the heating mode.
NOTE: 8°C HEATING mode can be used to help
keep areas that do not need to be fully heated
above freezing temperatures.
OPERATION INSTRUCTIONS (Continued)(Continued)
SLEEP MODE
SLEEP mode can be set in COOLING,HEATING
or DRYING mode.
This function gives you a more comfortable
environment for sleep.
• The appliance will automatically stop after it
has been operating for 8 hours.
• Fan speed is automatically set at low speed.
HOW TO SET SLEEP MODE
Each time button is pressed.
Result: The operation mode is changed in
sequence:
SLEEP MODE 1:
Cool Mode: Set temperature will increase
Heat Mode: Set temperature will decrease
iFEEL MODE
iFEEL mode can read the current room ambient
temperature by using a sensor built into the
remote control. The system will automatically
adjust to keep all areas of the room at the same
temperature.
NOTE: iFEEL mode function works best if
the remote control is placed on the opposite
side of the room as the indoor unit and out of
NOTE: Remote must still be within an
unblocked 21ft/7m signal receiving range to
communicate with indoor unit.
HOW TO SET iFEEL MODE
Press the iFeel button once.
Result: The transmit signal in the display will
appear, the iFeel function will be started.
NOTE: The default setting is iFeel inactive.
HOW TO CANCEL iFEEL MODE
Press the iFeel button once.
Result:
SLEEP MODE 2:
Cool Mode: Set temperature will increase
1°F/1°C after 6 hours, decrease by 1°F/1°C
after 7 hours. Temperature will then stay
Heat mode: Set temperature will decrease
2°F/2°C after 2 hours, increase 1°F/1°C after
6 hours, increase 1°F/1°C after 7 hours.
Temperature will then stay steady until
SLEEP MODE 3:
Cool Mode: Set temperature will increase 1°F/1°C
after 1 hour, increase by 2°F/2°C after 2 hours,
decrease 2°F/2°C after 6 hours, decrease 1°F/1°C
after 7 hours. Temperature will then stay steady
Heat mode: Set temperature will decrease
2°F/2°C after 1 hour, decrease by 2°F/2°C after
2 hours, increase 2°F/2°C after 6 hours, increase
1°F/1°C after 7 hours. Temperature will then stay
SLEEP MODE 4:
Set temperature will stay steady.
NOTE: Press SUPER, SMART MODE, ON/OFF
or FAN SPEED button cancel SLEEP mode.
By pressing “Sleep button” four times, or
selecting other modes like SUPER, SMART,
or FAN SPEED, you could cancel the sleeping
function of those units.
NOTE:
a received signal from remote will turn the
light back on.
DIMMER BUTTON
Press the button for about 5 seconds to
ECO MODE
In this mode, air conditioner will run the fan and
compressor on lowest frequency to save energy.
Press ECO button for about 3 seconds to start
ECO mode.
Result:
The indicator appears on the display.
Fan speed will be auto set to low.
AI SMART mode.
Press ON/OFF MODE, TEMP +, TEMP -,
FAN SPEED, SLEEP, QUIET or ECO button
to cancel ECO Mode.
Pressing ECO button for 1 second turns on
HI-NANO indicator, this feature is not available.
