Delta PMC-24V100W1AA Manual de usuario

Instruction Manual PMC-24V100W1AA

1. Safety Instructions

•To ensure sufficient convection cooling, always maintain a safety

distance of >20mm from all ventilated surfaces while the device is

in operation.

•The device is not recommended to be placed on low thermal

conductive surface, for example, plastics.

•Note that the enclosure of the device can become very hot

depending on the ambient temperature and load of the power

supply.

Do not touch the device while it is in operation or immediately after

power is turned OFF. Risk of burning!

•Do not touch the terminals while power is being supplied. Risk of

electric shock.

•Prevent any foreign metal, particles or conductors to enter the

device through the openings during installation. It can cause:

- Electric shock; Safety Hazard; Fire; Product failure

•Warning: When connecting the device, secure Earth connection

before connecting L and N. When disconnecting the device, remove

L and N connections before removing the Earth connection.

2. Device Descriptions

Refer to Fig. 1:

1 Input & Output terminal block connector

2 DC voltage adjustment potentiometer

3 DC OK control LED (green)

3. Installation of the Device

Refer to Fig. 2:

A Mounting holes for power supply assembly onto the mounting surface. Power

supply shall be mounted on minimum 2 mounting holes using M3 screw,

minimum 5mm length.

B This surface belongs to customer’s end system or panel where the power

supply is mounted.

C Connector

•Use flexible cable (stranded or solid), AWG no. 22-12. The torque at the

Connector shall not exceed 13Kgf.cm The insulation stripping length should

not exceed 0.275” or 7mm

4. Installation of Mounting Accessories

•Only use M3 screw < 6mm through the base mounting holes. This is to keep

a safety distance between the screw and internal components.

•Refer to Fig. 4:

Recommended mounting tightening torque: 4 ~ 8Kgf.cm

Fig. 4 Mounting Screw

Fig. 2 Mounting Orientation

www.delta.com.tw/industrialautomation

Side Mounting (Vertical) Base Mounting (Vertical) Side Mounting (Horizontal)

Fig. 3 Wire Type

Lug Stri

ed wire

Fig. 1 Device Descriptions

Base surface

Top

Side surface

Ventilated surface

Call 1(800)985-6929 for Sales

deltaacdrives.com

[email protected]

Call 1(800)985-6929 for Sales

deltaacdrives.com

[email protected]

側面

底面

!ֹϡᄲځ!

1. щБఢቑ!

•與通風表面保持至少 20mm 的安全距離，以確保對流冷卻充分。

•本產品不適合擺放在低熱導體，例如：塑膠。

•受環境溫度及產品負載的影響，本機外殼溫度會很高，因此在上電時或切

斷電源後短時間內不要觸摸本機，以免燙傷。

•請勿在上電時觸摸連接端子，以防電擊危險。

•安裝過程中，應避免金屬元件或金屬導體通過空隙或通風孔進入到產品

內，否則會引起下列狀況。

－電擊 ; 安全危害 ; 火災 ; 產品異常

•警告：在連接產品電源供應時，產品必須先接地然後才接 L和N。當要解

開電源供應時，必須先把 L和N解開然後才把接地解開。

2. யݡγ៍௜!

依據圖一:

1 輸入/輸出連接端子

2 直流電壓調節電位器

3 直流電控制 OK 指示燈（綠色）

PMC-24V100W1AA

3. யݡ׽ؠё!

依據圖二:

在把產品安裝在固定表面時,將螺絲鎖入此固定孔. 產品應該用長度至少 5mm 的M3

螺絲鎖入至少兩個固定孔。

此固定表面為客戶系統表面。

輸入/輸出連接端子

•電線的設計可使用多股或實心，AWG no.22-12。扭矩不應該超過 13Kgf.cm 剝線的

長度不應該超過 0.275” 或者 7mm

4. І௡Ъщ྅!

•在把配件裝上產品時，請使用長度不超過 6mm 的M3 螺絲鎖入產品底面的固定孔。

這是為了確保螺絲和內部元件間有足夠的絕緣距離。

•依據圖四：

建議配件固定螺絲扭矩為 4 ~ 8Kgf.cm

圖二固定方位

www.delta.com.tw/industrialautomation

ݬۡ઎ࢬ׽ؠ! ݬۡغࢬ׽ؠ! π઎ࢬ׽ؠ!

圖三電線類型

接線端子剝線

圖一產品外觀介紹圖四固定螺絲

頂面

通風表面

Call 1(800)985-6929 for Sales

deltaacdrives.com

[email protected]

Call 1(800)985-6929 for Sales

deltaacdrives.com

[email protected]

Otros manuales de Fuente de alimentación de Delta

Delta

Delta PMC-12V100W1AA Manual de usuario

Delta

Delta MCS-600 Series Manual de instrucciones

Delta

Delta CliQ II DRP024V120W3B Series Manual de instrucciones

Delta

Delta PMC-24V100W1AA Manual de usuario

Delta

Delta FORCE-GT Series Manual de instrucciones

Delta

Delta PMC Series Manual de usuario

Delta

Delta PMC Series Manual de usuario

Delta

Delta PMH-100WCL Series Manual de usuario

Delta

Delta PMC-48V600W1B Series Manual de usuario

Delta

Delta IMA-1000 Series Instrucciones de instalación y funcionamiento

Delta

Delta PMC-12V035W1AA Manual de usuario

Delta

Delta PMT2 75 W Series Manual de instrucciones

Delta

Delta LYTE II Manual de instrucciones

Delta

Delta DRS-24V100W1A Series Manual de instrucciones

Delta

Delta GPS-650JB E A22 Manual de usuario

Delta

Delta CliQ DRP024V060W1AA Manual de instrucciones

Delta

Delta Platinum GPS-650LB A A22 Manual de usuario

Delta

Delta ZBF-12V/3A Manual de usuario

Delta

Delta Sync DRS-12V50W1N Series Manual de instrucciones

Delta

Delta PMC-24V035W1AA Manual de usuario

Delta

Delta LOYTEC LPOW-2415A Manual de usuario

Delta

Delta PMR V320WC Series Manual de usuario

Delta

Delta LYTE II Manual de instrucciones

Delta

Delta GPS-1000D8 A A22 Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Agilent Technologies

Agilent Technologies 6631B Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

HP 6200B Manual de servicio

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario