Delta UNOlite Manual de usuario

User Manual

VER 0.4

Revision

Date

Version

Description

2022/ 11 / 11

0.1

Initial Version

2022/ 11 / 12

0.2

Modified some typos

2022/ 12/ 27

0.3

Update missing icon, add APP direct link for China

2023/ 1 / 5

0.4

Add sensor notice

What’s Included

UNOlite

Surface / Drywall mount

Electrical box mount

Drywall screws

and anchors (1 pairs)

Quick start guide

Important Safeguards

Please read the safety warnings before use and take the necessary precautions to reduce

the risk of fire, electric shock, or injury. The Delta limited warranty applies only if the unit is

used according to these instructions.

WARNING!!

To reduce safety risks, always use service personnel from the manufacturer or service

provider, or other qualified personnel for installation and maintenance.

Make sure the power is OFF during installation or maintenance.

DO NOT tamper with or use nonofficial spare parts for repair or maintenance.

DO NOT use the device in environments with high humidity or possible direct

exposure to water.

DO NOT use the device in an outdoor environment.

DO NOT use the device near heat sources such as radiators, furnaces, ovens, or

stoves.

When the DIP switch and terminal block behind the product are changed, be sure to

power off and then power on after setting.

Do not force the connector into the port. Check the port for foreign object obstruction.

If the product is damaged due to human operation, such as inserting the wrong pin, or

not connecting the power in accordance with the power input specifications provided

in the data sheet, it is not liable for warranty.

Getting Started

The UNOlite is a building-grade air quality monitor that can measure the ambient

temperature / humidity / CO2 / PM1 / PM2.5 / PM10 / TVOC and provide multiple protocols

for wired or wireless networks. Further information can be found on the UNOlite Resource

at: https://isdweb.deltaww.com/resources/enter

①

Power LED

⑦

RS-485

②

Status LED

⑧

Direct Wiring (12-24VDC or 24VAC)

③

Switch Button

⑨

DIP Switches

④

IAQ RGB LED

⑩

Power Adapter Hole

⑤

GND

⑪

Hardware Reset

⑥

Factory Reset Button

Externals and Air Flow

Air is drawn into the UNOlite from the lower side, and there is natural air exchange on

each side. It is vital that neither side of the device is covered. Any changes in airflow may

affect the readings and accuracy.

Power and Connectivity

The UNOlite provides multiple power and connectivity options:

Power:

Adapter: Only use the cable and charger/adapter supplied with the device

AC/DC direct wiring: Used for power supplies of 12-24V DC or 24V AC

Connectivity:

2.4GHz Wi-Fi (802.11 b/g/n)

RS-485: Used for Modbus RTU communication, see the UNOlite Modbus User Manual

for the detailed information

BACnet: Used for BACnet MS/TP. See the UNOlite BACnet User Manual for detailed

information.

Hardware Interface

IAQ LED Indications:

Standard operation

Description

Breathing light BLUE

Device is booting

Breathing light GREEN

Indoor air quality is good

Breathing light YELLOW

Indoor air quality is moderate

Breathing light RED

Indoor air quality is unhealthy

Breathing light PURPLE

Indoor air quality is very unhealthy

Steady OFF

Device is in DIM mode

Status LED Indications:

Standard operation

Description

Power

Steady OFF

Device’s power does not work

Steady ON

Device’s power is working normally

BLE

Steady OFF

No BLE connection

Steady ON

In BLE connection

Flash rapidly

In BLE binding process

Wi-Fi

Steady OFF

No Wi-Fi connection

Steady ON

Wi-Fi connected

Equipment

(RESERVED NOW)

Steady OFF

Equipment is OFF

Steady ON

Equipment is running

Flash slowly

Can’t find/connect equipment.

Filter status

(RESERVED NOW)

Steady OFF

Filter health is good

Steady ON

Need to replace filter

In factory reset operation:

Standard operation

Description

All LED

Flash rapidly

Device is performing a factory reset

Key

Description

Hardware reset

Press this button to trigger a power-cut reboot.

Factory reset

Click this button 3 times within 2 seconds to trigger a factory reset.

The values below will be restored to default:

▪Modbus baud rate

▪BACnet saved mac address

▪Wi-Fi MQTT broker setting (Wi-Fi model)

▪CO2 auto baseline calibration is ON

▪Sensor calibration settings

Switch button

ON/OFF IAQ and status LED (Enter/leave DIM mode)

NOTE: Use a paper clip to press the keys.

iOS APP Android APP 安卓 APK 连结 UNOweb(Wi-Fi Model)

DIPs

Description

1-6

Refer BACnet or Modbus User Manual

NOTE: PIN6 is unused in Modbus mode

Mode switch ON : BACnet MS/TP OFF : Modbus RTU

RS485 terminator resistor (120 ohm)

NOTE: The dips should be adjusted to proper position in the power off state. Adjust the dips, then

power on the device.

Installation

The UNOlite can be mounted on a concrete block wall, drywall, ceiling, or to an electrical

box. For detailed instructions on the installation, power, and connectivity setup, please visit

our support center website at https://isdweb.deltaww.com/resources/ or scan the QR code

below.

IoT Application

Warranty Information

Delta provides a 1-year limited manufacturer warranty on the UNOlite. To obtain a copy of

the warranty for this product, please visit

https://isdweb.deltaww.com/resources/warranty.html or scan the QR code below.

Troubleshooting

For frequently asked questions about the UNO series sensors, please visit the FAQ

webpage at https://isdweb.deltaww.com/resources/faq/index.html or scan the QR code

below.

The product was calibrated in the factory, and no additional calibration is required. If

a sensor value is affected by the environment at your site, please contact the

distributor for manual calibration.

This controller has built-in multiple sets of precision sensors. Collision and vibration

during transportation may affect its readings. It is recommended that you turn it on

and install it, and then wait for about one hour until the chamber reaches balance.

【Note】The temperature module built into this product has been calibrated in the factory, but

the accuracy may be impacted by the installation environment, such as nearness to a heat

source or high air flow. To get more accuracy, calibrate the product after installation. Wait for

one hour after installation for calibration. User can use APP’s engineer mode to calibrate it.

After you turn on the device, these sensors needs to warm-up for 5 minute or less for PM2.5,

PM10, and carbon dioxide, and 5 minutes for formaldehyde, carbon monoxide, ozone, and

TVOC. Sensor data is updated every 10 seconds.

The CO2 sensor uses an Automatic Baseline Calibration (ABC) algorithm to maintain accuracy.

If the component encounters vibration when it is reinstalled in a different place, values may drift.

Please keep operation for weeks to find the baseline in this case.

【Note】Follow the instructions below to facilitate the automatic calibration of CO2

components.

‧This product needs a continuous power supply, please install it in a fixed position

‧The indoor environment reaches the level of the outdoor environment for four

consecutive hours each week

For additional support,

please contact your sales representative

or email us at uno.service@deltaww.com

Tabla de contenidos

Otros manuales de Monitor de Delta

Delta

Delta DOP-107EV Manual de usuario

Delta

Delta PPM R1E Manual de instalación

Delta

Delta UNO-C07X011 Manual de usuario

Delta

Delta DOP-107H Series Manual de usuario

Delta

Delta DOP-100 Series Manual de usuario

Delta

Delta TP70P Manual de usuario

Delta

Delta uno next Manual de usuario

Delta

Delta DOP-103BQ Manual de usuario

Delta

Delta Vivitek NovoDisplay DK430 Manual de usuario

Delta

Delta IIYAMA-E2483HSU-B5 24 " Manual de usuario

Delta

Delta Vivitek NovoTouch EK860i Manual de usuario

Delta

Delta VMT-221IP Manual de usuario

Delta

Delta IIYAMA-X2783HSU-B3 Manual de usuario

Delta

Delta DOP-107BV Manual de usuario

Delta

Delta R3E Manual de usuario

Delta

Delta TV-908A Manual de usuario

Delta

Delta DOP-103BQ Manual de usuario

Delta

Delta DOP-110CS Manual de usuario

Delta

Delta VMT-173 Manual de usuario

Delta

Delta Vivitek NovoTouch EK650i Manual de usuario

Delta

Delta VMT-271 Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación