Delta C2000 Series Manual de usuario

&(



PLEASE READ PRIOR TO INSTALLATION FOR SAFETY.

DANGER

;AC input power must be disconnected before any wiring to the AC motor drive

is made.

;Even if the power has been turned off, a charge may still remain in the DC-link

capacitors with hazardous voltages before the POWER LED is OFF. Please do

not touch the internal circuit and components.

;There are highly sensitive MOS components on the printed circuit boards.

These components are especially sensitive to static electricity. Please do not

touch these components or the circuit boards before taking anti-static

measures. Never reassemble internal components or wiring.

;Ground the AC motor drive using the ground terminal. The grounding method

must comply with the laws of the country where the AC motor drive is to be

installed.

;DO NOT install the AC motor drive in a place subjected to high temperature,

direct sunlight and inflammables.

CAUTIO

;Never connect the AC motor drive output terminals U/T1, V/T2 and W/T3

directly to the AC mains circuit power supply.

;Only qualified persons are allowed to install, wire and maintain the AC motor

drives.

;Even if the 3-phase AC motor is stop, a charge may still remain in the main

circuit terminals of theAC motor drive with hazardous voltages.

;If the AC motor drive is stored in no charge condition for more than 3 months,

the ambient temperature should not be higher than 30 °C. Storage longer than

one year is not recommended, it could result in the degradation of the

electrolytic capacitors.

NOTE

The content of this manual may be revised without prior notice. Please consult our distributors or download the most

updated version at http://www.delta.com.tw/industrialautomation

Table of Contents

CHAPTER 1 INTRODUCTION ....................................................................................................1-1

CHAPTER 2 INSTALLATION ....................................................................................................2-1

CHAPTER 3 UNPACKING ..........................................................................................................3-1

CHAPTER 4 WIRING ..................................................................................................................4-1

CHAPTER 5 MAIN CIRCUIT TERMINALS ................................................................................5-1

CHPATER 6 CONTROL TERMINALS.........................................................................................6-1

CHAPTER 7 OPTIONAL ACCESSORIES................................................................................7-1

CHAPTER 8 OPTION CARDS ....................................................................................................8-1

CHAPTER 9 SPECIFICATION ....................................................................................................9-1

CHAPTER 10 DIGITAL KEYPAD ..............................................................................................10-1

CHAPTER 11 SUMMARPY OF PARAMETERS........................................................................ 11-1

CHPAPTER 12 DESCRIPTION OF PARAMETER SETTINGS..................................................12-1

CHAPTER 13 WARNING CODES.............................................................................................13-1

CHAPTER 14 FAULT CODES AND DESCRIPTIONS...............................................................14-1

CHAPTER 15 CANOPEN OVERVIEW......................................................................................15-1

CHAPTER 16 PLC FUNCTION.................................................................................................16-1

CHAPTER 17 HOW TO SELECT THE RIGHT AC MOTOR DIRVE...........................................17-1

CHAPTER 18 SUGGESTIONS AND ERROR CORRECTIONS FOR STANDARD AC MOTOR

DRIVES .....................................................................................................................................18-1

Application Control BD V1.01;

Keypad V1.01;

Summary of Updates|C2000 Series

0-1

Publication History

The following changes summarize the differences to the C2000 Simplified Manual, Version

5011694702.

Chatpers Changes Detail

[Table of Content] New

New Chapters:

• Chapter 2 Installation

• Chapter 7 Optional Accessories

• Chapter 12 Description of Parameter Settings

• Chapter 15 CANopen Overview

• Chapter 16 PLC Function

• (Applicable model, AC motor drive selection)

Applicable model

AC motor drive selection

New Frame FRAMEA~H

KPC-CC01 digital keypad

[01 Introduction]

Update Serial number

New Mounting clearances and wiring information[02 Installation] Update Unpacking details moved to CH3

[03 Unpacking] New FRAME F~H

FRAME H secure the drive

FRAME F~H lifting weight

[04Wiring] New RB-RC power protection system diagram

Updates Wiring diagram 1, 2

Control circuit description

Figure1,2

Figure 3 FRAME E-H DC-LINK

Remove the cover for wiring figure

[05 Main circuit terminal] Update

Main circuit terminal specifications

FrameA~E (max. and min. wire gauge,torque, note, diagram)

[06 Control circuit terminal] Update Remove the cover for wiring figure

[07 Optional Acessories ] Update 1. All Brake Resistors and Brake Units Used in AC Motor Drives

2. AC Reactor

3. EMI Filter

4. Fan kit Model 『MKC-FFKB』

5. Fan kit Model 『MKC-GFKM』

New EMC-BPS01: terminal Screw Sepecifications[08 Option cards] Update EMC-PG01O, EMC-PG01L, EMC-PG01U, EMC-PG01R:

terminal Screw epecifications, wiring diagram

New AC Drive Weight

Braking Chopper

DC reactor

EMC Filter

[09 Specification] Update

EMC-COP01

[10 Digital Keypad] New 10-4 Fault Code Description of Digital Keypad KPC-CC01

Group 00

Pr. 00-04, 00-29, 00-40,

Group 01

Pr. 01-34, 01-43, 01-44,

Goup 02

Pr.02-10, 02-12, 02-18~02-20, 02-34

Goup 03

Pr.03-06, 03-15~03-17

[11 Summary of Parameters]

[12 Description of Parameters] Update

Group 05

0-2

Pr.05-05~05-09, 05-018~05-21

Group 06

Pr.06-48, 06-69, 06-70

Group 07

Pr.07-05

Group 08

Pr.08-00, 08-06

Group 09

Pr.09-04, 09-31, 09-43

Group 10

Pr.10-31~10-42

Group 11

Pr.11-02, 11-13, 11-39, 11-42

NEW Pr. 02-55~02-58,

[13 Warning Codes] New PLra

New Fault code:

“ryF” “PGF5”, “FStp”, “ictE”

Update LCM display icons

Fault codes:

“oH1”, “oH2”, “Uoc”, “Voc”, “Woc”,

[14 Fault Codes and

Descriptions]

Remove LED display content

Fault code:

“PWR”, “ccod”, “ocU”, “ovU”,

[15 CAN Slave] Update 15.3 How to control by CANopen

[16 PLC] Update 16.6 Commands

16.7 Error Code and Troubleshoot

[18 ] NEW New charpter

Chapter 1 Introduction|C2000 Series

1-1

Chapter 1 Introduction

Receiving and Inspection

After receiving the AC motor drive, please check for the following:

1. Please inspect the unit after unpacking to assure it was not damaged during shipment. Make sure

that the part number printed on the package corresponds with the part number indicated on the

nameplate.

2. Make sure that the voltage for the wiring lie within the range as indicated on the nameplate. Please

install the AC motor drive according to this manual.

3. Before applying the power, please make sure that all the devices, including power, motor, control

board and digital keypad, are connected correctly.

4. When wiring the AC motor drive, please make sure that the wiring of input terminals “R/L1, S/L2,

T/L3” and output terminals”U/T1, V/T2, W/T3” are correct to prevent drive damage.

5. When power is applied, select the language and set parameter groups via the digital keypad

(KPC-CC01). When executes trial run, please begin with a low speed and then gradually increases

the speed untill the desired speed is reached.

Nameplate Information

MODEL:VFD007C43A

INPUT:

Normal Duty: 3PH 380-480V 50/60Hz 4.3A

Heavy Duty: 3PH 38 0-480V 50/60Hz 4.1A

OUTPUT:

Version:

FREQUENCYRANGE:

Normal Duty: 3PH 0-480V 3A 2.4KVA 1HP

Heavy Duty: 3PH 0- 480 V 2.9A 2.3KVA 1 HP

Normal Duty: 0-600Hz

Heavy Duty: 0-300Hz

VX.XX

007C43A7T9300002

DELTA E LEC TRONIC S. INC .

MADE IN XXXXXXX

AC Drive Model

Input Voltage/Current

Output Voltage/Current

Frequency Range

Firmware Version

Certifications

Serial Number

Enclosure type (IPXX)

Chapter 1 Introduction|C2000 Series

1-2

Model Name

VFD 007 C 43 A

23:230V 3-PHASE

43:460V 3-PHASE

007:1HP(0.75kW)~ 3350:475HP(335k

Versi on ty pe

Input voltage

C2000 series

Applicable motor capacity

Refer to the specifications for details

Series name(Variable Frequency Drive)

Serial Number

007C43A0 T 9 30 0002

460V 3-PHASE 1HP(0.75kW)

Production number

Production week

Production year

Production factory

Model number

T: Tauyuan W: Wujian

S: Shanghai

Chapter 1 Introduction|C2000 Series

1-3

RFI Jumper

RFI Jumper: The AC motor drive may emit the electrical noise. The RFI jumper is used to suppress the

interference (Radio Frequency Interference) on the power line.

Frame A~C

Screw Torque: 8~10kg-cm(6.9-8.7 lb -in.)

Loosen the screws and remove the MOV-PLATE. Fasten the screws back to the original position after

MOV-PLATE is removed.

Chapter 1 Introduction|C2000 Series

1-4

Frame D~H

Remove the MOV-PLATE by hands, no screws need to be loosen.

Main power isolated from earth:

If the AC motor drive is supplied from an isolated power (IT power), the RFI jumper must be cut off. Then

the RFI capacities (filter capacitors) will be disconnected from ground to prevent circuit damage

(according to IEC 61800-3) and reduce earth leakage current.

CAUTION!

1. When power is applied to the AC motor drive, do not cut off the RFI jumper.

2. Make sure main power is switched off before cutting the RFI jumper.

3. The gap discharge may occur when the transient voltage is higher than 1,000V. Besides,

electro-magnetic compatibility of the AC motor drives will be lower after cutting the RFI jumper.

4. Do NOT cut the RFI jumper when main power is connected to earth.

5. The RFI jumper cannot be cut when Hi-pot tests are performed. The mains power and motor must be

separated if high voltage test is performed and the leakage currents are too high.

6. To prevent drive damage, the RFI jumper connected to ground shall be cut off if the AC motor drive is

installed on an ungrounded power system or a high resistance-grounded (over 30 ohms) power

system or a corner grounded TN system.

Chapter 1 Introduction|C2000 Series

1-5

Dimensions

Frame A

VFD007C23A; VFD007C43A/E; VFD015C23A; VFD015C43A/E; VFD022C23A; VFD022C43A/E;

VFD037C23A; VFD037C43A/E; VFD040C43A/E; VFD055C43A/E

Unit: mm [inch]

Frame W H D W1 H1

D1* S1 Φ1 Φ2 Φ3

A1 130.0

[5.12]

250.0

[9.84]

170.0

[6.69]

116.0

[4.57]

236.0

[9.29]

45.8

[1.80]

6.2

[0.24]

22.2

[0.87]

34.0

[1.34]

28.0

[1.10]

D1*: Flange mounting

Otros manuales para C2000 Series

Tabla de contenidos

Otros manuales de Accionamiento de CC de Delta

Delta

Delta VFD-EL-W Series Manual de usuario

Delta

Delta C2000 Series Manual de usuario

Delta

Delta CP2000 Series Manual de usuario

Delta

Delta VFD-L-I Series Manual de usuario

Delta

Delta VFD-ED Series Manual de usuario

Delta

Delta C2000 Series Manual de usuario

Delta

Delta VFD-MS300 Series Manual

Delta

Delta VFD-B Series Manual de usuario

Delta

Delta VFD-EL-W Series Manual de usuario

Delta

Delta MS300 Series Manual de usuario

Delta

Delta VFD-B Manual de usuario

Delta

Delta VFD-B 230V Series Manual de usuario

Delta

Delta PMC-24V150W1AA Manual de usuario

Delta

Delta MH300 Manual de usuario

Delta

Delta CT2000 Series Manual de usuario

Delta

Delta CP2000 Series Manual de usuario

Delta

Delta VFD-A Series Manual de usuario

Delta

Delta EB3000 Series Manual de usuario

Delta

Delta VFD300C43S-HS Manual de usuario

Delta

Delta VFD-E Manual de usuario

Delta

Delta VFD-VL Series Manual de usuario

Delta

Delta CFP2000 Series Manual de usuario

Delta

Delta CP2000 Series Manual de usuario

Delta

Delta VFD-M Series Manual de usuario

Manuales populares de Accionamiento de CC de otras marcas

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manual de usuario

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manual de lista de piezas

Chamberlain Garog

Chamberlain Garog D Series Manual de usuario

Parker

Parker PDS Series Manual de usuario

Festo

Festo DGC G Series Guía de configuración

Binks

Binks QS-5012-1-CE Manual de usuario

Danfoss

Danfoss VLT 2800 Series Hoja de especificaciones

ABB

ABB ACQ580-01 Series Manual de instalación

YASKAWA

YASKAWA CANopen SI-S3 Manual de usuario

GE D20A6 Manual de usuario

Unex

Unex MC-D-250-1000-050W-TW Manual de usuario

Geckodrive

Geckodrive G213V Manual de usuario

ABB

ABB RSYC-01 Manual de usuario

Rockwell Automation

Rockwell Automation PowerFlex 700S Manual del propietario

WEG

WEG DeviceNet CFW500 Manual de usuario

Siemens

Siemens SINAMICS G Hoja de datos

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Instrucciones de funcionamiento

SOMFY

SOMFY JR RU 30 Manual de usuario