Delta DPB Series Manual de usuario

- 1 -

Series Pressure Sensor

Instruction Sheet

Thank you very much for choosing Delta DPB series pressure sensor. Please read this instruction sheet carefully before using your DPB.

Keep this instruction sheet handy for quick reference.

Warning

DANGER! CAUTION! ELECTRIC SHOCK!

DPB is a pressure measurement device. DO NOT use it out of its specification. Improper pressure or incorrect wiring may

cause series injuries on staff or damages on other devices.

1. Keep away from high-voltage and high-frequency environment during the installation in case of interference. Prevent using the device in

premises which contain:

(a) dust or corrosive gas; (b) high humidity and high radiation; (c) shock and vibration.

2. DPB can only be used for air pressure measurement and should avoid corrosive, inflammable or toxic gas measurement.

3. Make sure the power supply is switched off when installing or dismounting DPB and the pressure source stops its action in case harms

occur on human body and properties.

4. DO use parts compatible to the specification of the pressure pore for connection to avoid mistaken measurement or safety problems.

5. Before switching on the power supply, check the signal connection, e.g. the input voltage and polarity. Voltage that is too high may cause

damages on DPB.

6. DO use dry cloth and DO NOT use acid or alkaline liquid to clean the device.

 Product Profile & Outline

1. Pressure/parameter display 6. SET key

2. SV/setup item display 7. DOWN key

3. Pressure unit display 8. Power supply and output terminals

4. Digital output 1/2 indicator 9. Pressure input pore

5. UP key

Contents in the pack: Pressure sensor, signal wire, instruction sheet

Optional accessories: Panel mounting parts DPA-PFKit, metal mounting parts DPA-FMKit

5 67

- 2 -

 Ordering Information

Series name DPB: Delta DPB series pressure sensor

Measurable pressure range

01: -100kPa ~ 100kPa

10: -100kPa ~ 1,000kPa

3Output types

N: NPN output

P: PNP output

Pressure pore types

P: Outer pore PT 1/8, inner pore M5

N: Outer pore NPT 1/8, inner pore M5

G: Outer pore G 1/8, inner pore M5

Electrical Specifications

Power supply

Voltage range 12 ~ 24V DC +/- 10% no isolation

Power consumption 40mA Max.

Pressure

measurement

Pressure type Non-corrosive gas, gauge type

Measurable range

DPB01: -100kPa ~ 100kPa

DPB10: -100kPa ~ 1,000kPa

Max. durable pressure

DPB01: 200kPa

DPB10: 1,500kPa

Accuracy +/- 3% entire process

Temperature inaccuracy +/- 2% entire process

Display

Setup display 2-line LCD display, 4 digits for measured value and 3.5 digits for setup display

Status display LCD output status display

Display mode 3 colors for different modes

Cycle 100ms, 250ms, 500ms, 1,000ms

Output

Number of outputs Built-in 2 NPN or PNP transistor digital outputs

Transistor output

NPN: Max. durable pressure 30V/100mA, residual voltage 1.5V

PNP: Max. durable pressure 30V/100mA, residual voltage 1.5V

Response time 2ms, 4ms, 10ms, 30ms, 50ms, 100ms, 250ms, 500ms, 1,000ms, 5,000ms

Output inaccuracy Linear inaccuracy: < +/- 2% entire process

Pore size

P Outer pore PT 1/8, inner pore M5

N Outer pore NPT 1/8, inner pore M5

G Outer pore G 1/8, inner pore M5

Shock immunity 10 ~ 500Hz, 10mm 3 axes for 2 hours

Vibration immunity Max. 100m/ s23 axes 6 directions, 3 times each

Ambient temperature 0°C ~ +50°C

Storage temperature -20°C ~ +65°C

Altitude < 2,000m

Ambient humidity 35% ~ 80% RH (non-condensing)

- 3 -

How to Set up Parameters

Switching modes: DPB will be in the “Measuring Mode” when it is switched on, displaying PV and SV. Press for more than 2 seconds

in this mode to switch to the “Quick Setup Mode”. Press for more than 4 seconds in the “measuring mode” to switch to “Advanced

Setup Mode”. Press in the “Quick Setup Mode” or “Advanced Setup Mode” to return to the “Measuring Mode”.

Setting up parameters: In the three modes, press once to select the parameter to set up. When you find the parameter to be set up

or modify, use to modify the setting.

Quick Setup Mode:

Advanced Setup Mode:

Switching on DPB

Measuring Mode

Advance Setup

Mode

Press > 4 secs.

Press > 2 secs.

Quick Setup

Mode

Press > 4 secs.

- 4 -

Measuring Mode:

Quick Setup Mode Advanced Setup Mode Measuring Mode

Set up OUT1 mode

Press 

Set up auxiliary display

(Change SV display method)

Press 

Set up upper limit of OUT1

(Set OUT1 to hysteresis mode / window

mode)

Press 

Set up OUT2 mode

Press 

Set up displayed speed

Press 

Set up lower limit of OUT1

(Set OUT1 to hysteresis mode / window

mode)

Press 

Set up N.O./N.C. of OUT1 and

OUT2

Press 

Set up hysteresis

Press 

SV of OUT1

(Set OUT1 to easy mode)

Press 

Set up output response time

Press 

Set up switching color referencing

output items

Press 

Set up upper limit of OUT2

(Set OUT2 to hysteresis mode / window

mode)

Press 

Set up PV display color

Press 

Set up code

Press 

Set up lower limit of OUT2

(Set OUT2 to hysteresis mode / window

mode)

Press 

- 5 -

Quick Setup Mode Advanced Setup Mode Measuring Mode

Set up unit

Press Return to “set up OUT1 mode”

Return to default settings

Press Return to “set up auxiliary

display”

SV of OUT2

(Set OUT2 to easy mode)

Press Returning to output setting

Initial Setting

1. Units: DPB provides many units for users, including kPa, kgf/cm2, bar, psi, mmHg and inchHg. In the easy mode, you can press and

find to set the unit to the desired one.

2. Output status: You can set up 2 output status in DPB, N.O. (normally open) and N.C. (normally closed). In the easy mode, you can press

and fine to set up the output status for OUT1 and OUT2.

3. Response time: Referring to the time required for the pressure to reach output status. For example, “50” refers to once the pressure has

reached the output status, it has to last for 50ms before the output starts to operate. In the easy mode, press and find .

Use to set up the response time.

Output Mode Setting

There are 3 output modes in DPB: Easy, Hysteresis and Window

1. Easy Mode: Set up pressure P. When the pressure measured is bigger than (P + dP), the output will be ON. When the pressure measured

is smaller than P, the output will be OFF. (See Figure 1: Output in Easy Mode)

In the “Measuring Mode”, press and find (OUT1) and (OUT2). Use to set up P value.

In the “Advanced Setup Mode”, press and find . Use to set up “dP” value.

[Figure 1: Output in Easy Mode]

2. Hysteresis Mode: Set up pressure Hi/Lo. When the pressure measured is bigger than the Hi value, the output will be ON. When the

pressure measured is smaller than the Lo value, the output will be OFF. (See Figure 2: Output in Hysteresis Mode)

In the “Measuring Mode”, press and find (OUT1 Hi), (OUT1 Lo), (OUT2 Hi) and (OUT2

Lo). Use to set up Hi/Lo values.

[Figure 2: Output in Hysteresis Mode]

3. Window Mode: Set up pressure Hi/Lo. When the pressure measured is bigger than Hi or smaller than Lo, the output will be OFF. When the

pressure measured is bigger than Lo and smaller than Hi, the output will be ON. (See Figure 3: Output in Window Mode)

- 6 -

In the “Measuring Mode”, press and find (OUT1 Hi), (OUT1 Lo), (OUT2 Hi) and (OUT2

Lo). Use to set up Hi/Lo values.

In the “Advanced Setup Mode”, press and find . Use to set up “dP” value.

[Figure 3: Output in Window Mode]

Note: Supposed the output is ON and the output status is set to N.O. (normally open), the output will then be off. If the output status is set

to N.C (normally closed), the output will then be on. Supposed the output is OFF and the output status is set to N.O., the output will then be on.

If the output status is set to N.C., the output will then be off.

Zero Returning

In the "Measuring Mode”, press together, and you will see . The zero returning will start. Release the keys to end the zero

returning.

Key Locking Function

Lock On: Press and together for 2 seconds until is displayed. You will then see the display of pressure value (PV) and

set value (SV).

Lock Off: Press and together for 2 seconds until is displayed. You will then see the display of pressure value (PV) and

set value (SV).

Lock Display: Press any key in the key locking mode, and you will see the display of pressure value (PV) and (SV). Release the

key, and the PV and SV will return to original values.

Switching Colors

In DPB, different output statuses can have different display colors. The output statuses for DPB are “OUT1”, “OUT2”, ”OUT1 and OUT2”,

“OUT1 or OUT2”. See below explanations for how to set:

1. Setting up output status: In the “Measuring Mode”, press for more than 4 seconds and release the key after you see . You

are now in the “Advanced Setup Mode”. Press for 4 times and find the switching color referencing items (see Advanced Setup Mode

chart). Use to select the referencing item you'd like.

2. Switching colors: In the “Measuring Mode”, press for more than 2 seconds to enter the “Quick Setup Mode”. Press for 4 times

and find the parameter for setting up colors (see Quick Setup Mode chart). Use to select the color you’d like.

Note: “OUT1 and OUT2” will be ON only when both OUT1 and OUT2 are ON; otherwise, it will be OFF. “OUT1 or OUT2” will be OFF only

when both OUT1 and OUT2 are OFF; otherwise, it will be ON.

Code

DPB offers codes for the user to set up. In the “Measuring Mode”, press for more than 4 seconds and release the key after you see

. You are now in the “Advanced Setup Mode”. Press for 5 times to find the parameter to set up codes (see Advanced Setup Mode

chart). displays in turn.

- 7 -

See the meanings of codes in the table below:

Code

1st digit 2nd digit 3rd digit 4th digit

OUT1 mode N.O./N.C. OUT2 mode N.O./N.C. Response time Color Referencing item for color

Easy

N.O.

Easy

N.O. 2ms

Red when

OUT1

N.C. N.C. 4ms

OUT2

Hysteresis

N.O.

Hysteresis

N.O. 10ms OUT1 and OUT2

N.C. N.C. 30ms

OUT1 or OUT2

Window

N.O.

Window

N.O. 50ms

Green

when ON

OUT1

N.C. N.C. 100ms

OUT2

- - - - 250ms OUT1 and OUT2

- - - - 500ms OUT1 or OUT2

- - - - 1,000ms

Red

OUT1

- - - - 5,000ms OUT2

- - - - - OUT1 and OUT2

- - - - - Red

OUT1 or OUT2

- - - - -

Green

OUT1

- - - - - OUT2

- - - - - OUT1 and OUT2

- - - - - OUT1 or OUT2

Code

6th digit 7th digit 8th digit

Pressure unit Speed Auxiliary display Hysteresis setting

kPa

100ms

Standard 0

kgf/cm2Off 1

bar Unit. 2

psi

250ms

Standard. 3

mmHg Off 4

inchHg Unit 5

500ms

Standard 6

- Off 7

- Unit 8

1,000ms

Standard 9

- Off A

- Unit B

- 8 -

How to Install Dimension

Panel: Use optional accessory DPA-PFKit.

To install the fixing frame, you have to purchase the optional

accessory: DPA-FMKit.

 Internal Circuit

(NPN output) (PNP output)

Terminals

1. Positive power supply input (brown)

2. Digital output 1 signal (black)

3. Digital output 2 signal (white)

4. None (orange)

5. Negative power supply input (blue)

Error Message

/ : If the 1/2 output load current is large than 150 mA, please check the reason why the load current is too large.

Tabla de contenidos

Otros manuales de Accesorios de Delta

Delta

Delta PB-C1001 Manual de usuario

Delta

Delta 41319 Series Manual de usuario

Delta

Delta AMBIS Manual de usuario

Delta

Delta DPA Series Manual de usuario

Delta

Delta InfraSuite RWD030R Manual de usuario

Delta

Delta GT-9000 Manual de usuario

Delta

Delta AS-BF Series Manual de usuario

Delta

Delta DNS-14 Guía del usuario

Delta

Delta dvp04pt-s Manual de usuario

Delta

Delta SH-WS02 Manual de usuario

Delta

Delta PB-A1002 Manual de usuario

Delta

Delta LE-50637 Manual de usuario

Delta

Delta LE-753112 Manual de usuario

Delta

Delta 46-896 Manual de usuario

Delta

Delta GRX Manual de usuario

Delta

Delta BIESEMEYER 78-955 Manual de usuario

Delta

Delta DVP-EH Series Manual de usuario

Delta

Delta ELEKTRA UV E-5 Manual de usuario

Delta

Delta DVP04TC-S Manual de usuario

Delta

Delta DPA Series Manual de usuario

Delta

Delta PB-Q1002 Manual de usuario

Delta

Delta Uno Sense S1649 Manual de usuario

Delta

Delta 36-601 Manual de usuario

Delta

Delta 50-2000 Instrucciones de instalación

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario