Delta Electronics DNS SIP Series Manual

Evaluation Procedure

(DEP-008 A)

The Delphi DNS Series of SIP type

POL converters

The DNS, 2.4~5.5V or 10~14V input,

programmable output, non-isolated point of load

DC/DC converters, are the latest offering from

one of the world’s largest power supply

manufacturers ―Delta Electronics, Inc. The

DNS converters have flexible and programmable

tracking and sequencing features to enable a

variety of startup voltages as well as sequencing

and tracking between power modules. With

creative design technology and optimization o

component placement, these converters possess

outstanding electrical and thermal performance,

as well as extremely high reliability under highl

stressful operating conditions. All models

possess a myriad of standard protection

features.

This document guides the user through the

evaluation procedures to qualify a POL module.

The data shown in this Evaluation Procedure is

for the SIP Package Type POL evaluation board.

Please refer to the appropriate technical data

sheet for detailed performance and technical

information for the specific POL units.

Evaluation Procedure

EP_DNS_SIP_08052004

DNS SIP Series

1.0 Purpose

This document guides the user in performing

electronic measurements on a DNS POL (point

of load) DC/DC converter using the Delta

Evaluation Board.

2.0 Relevant Documentation

The documentation and background information

listed below is relevant to this evaluation

procedure:

2.1 Appropriate date sheet for the DNS Series

unit under evaluation.

2.2 Power Module Evaluation Board Schematic.

2.3 Power Module Evaluation Board Layout.

2.4 General Test and Safety Procedures.

Delta Electronics, Inc.

3.0 Equipment Required

3.1 A DC Power Supply 0 - 20 V @ 0 - 20A (Agilent 6574A 0 -60V/0 - 35A or equivalent).

3.2 An oscilloscope (Tektronix TDS 3034 or equivalent) 4 Channel 300 MHz, equipped with a x1

scope probe, a x10 scope probe, and two BNC cables (length less than 20 inches/500mm)

3.3 Digital multi-meters, one with 20A range and ideally all with 4 1/2 digit resolution (DVM1, DVM2

and DVM3) (Zentech 2041 or equivalent).

3.4 An electronic load (Chroma 63030 or equivalent), 300W approximate rating, or a suitable

resistive load.

3.5 A DC power supply (GW GPC-3060D).

4.0 Equipment Set-Up and Description

Refer to the Power Module Evaluation Board Layout (See page 20) for reference designators cited

in this document and Figure 1. Set-up Diagram.

Figure 1. Set-up Diagram

4.1 Connect one lead from the “+” lead of the DC source (See Item 3.1) to the “20A” terminal of the

first multi-meter DVM1 (See Item 3.3). Then connect one lead from the “Common” of the DVM1

to the “Vin” pin of the Evaluation Board. DVM1 is used to measure the input current.

4.2 Connect one wire from the “-” lead of the DC source (See Item 3.1) to the “GND“ pin of the

Evaluation Board. Note: Use stranded leads at least equivalent to 14 AWG for all connections

in sections 4.1 and 4.2. The leads should be twisted to reduce noise coupling.

4.3 Connect the plus “+” and minus “-“ connection leads from a second multi-meter (See Item 3.3)

to the “SVin” and “SGND” pins on the Evaluation Board. This multi-meter is designated DVM2.

DVM2 is used to measure the input voltage.

4.4 Connect the plus “+” and minus “-“ connection leads from the third multi-meter (See Item 3.3) to

the “SVOUT” and “SGND” Pin on the Evaluation Board. The multi-meter is designated DVM3.

DVM3 is used to measure the output voltage.

4.5 Connect a BNC cable (length less than 20 inches/500mm) from BNC1 of the Evaluation Board

to Channel 1 of the oscilloscope (See Item 3.2). This cable is used to measure the input

voltage (between SVIN and SGND).

4.6 Connect a BNC cable (length less than 20 inches/500mm) from BNC2 of the Evaluation Board

to Channel 2 of the oscilloscope (See Item 3.2). This cable is used to measure the output

voltage (between SVOUT and SGND).

4.7 Connect the positive and negative power leads of the electronic load (ensuring correct polarity),

or an appropriate resistive load to the Evaluation Board output terminal pin (“Vout” for positive

power lead and “SGND” for the negative power lead).

4.8 Connect one lead from the “+” lead of the DC source (See Item 3.5) to the “12Vcc” on the

Evaluation Board. Then connect one lead from the “-” of the DC source (See Item 3.5) to the

“12VGND” on the Evaluation Board.

5.0 Thermal Management of the Converter

It is imperative that sufficient airflow needs to be provided to the converter at all times during all

portions of testing. Please refer to the applicable data sheet for the proper cooling and derating

necessary conditions to obtain accurate results when testing the converter.

6.0 Tests Performed

The following tests are performed at room temperature (+25 ℃).

6.1 Input Characteristics

 Input Voltage Range.

 Under-Voltage Lockout.

 No Load Input Current.

6.2 Output Characteristics

 Line Regulation.

 Load Regulation.

 Output Regulation.

 Output Voltage Set-point Programming

 Output Voltage Margining

 Output Voltage Tracking

6.3 Dynamic Characteristics

 Maximum Output Voltage Deviation (due to step change in load).

 Turn on Response time.

6.4 Thermal Characteristic

 Efficiency

7.0 Test Set-Up

7.1 Initial Set-Up

1) Examine the part number of the power module to determine that the correct module is

being evaluated. Note: DNS04S0A0S06P A would denote the SMT package, while

DNS04S0A0R06P A would denote the SIP package. This Evaluation Board is for use with

SIP package.

2) Set the multi-meter DVM1 to the DC current 20A range. Set multi-meters DVM2 and

DVM3 to DC voltage, auto ranging.

3) Electronic Load

Turn on the Electronic Load at CR mode (or resistive load) and adjust the current level.

The maximum rated output current is 6A. Ensure the output load does not exceed the

recommended maximum current.

4) SW1 is used for on/off Transient function test. Turn SW1 to the OFF position if this function

is not being used. Turn SW1 to the ON position if the Transient function test is required.

5) SW2 is used to enable or disable the converter.

For positive logic module, When SW2 is put in the ON position, the converter is ON and

when SW2 is put in the OFF position, the converter is OFF.

For negative logic module, When SW2 is put in the OFF position, the converter is ON, and

when SW2 is put in the ON position, the converter is OFF.

6) SW3 is used for the Output Voltage Set-Point Adjustment Range.

By an external voltage source:

If the converter requires a trim up, set the SW3_1 to ON position.

If the converter requires a trim down, set the SW3_2 to ON position.

By an external resistor:

If the converter requires a trim up to Vo,set, set the SW3_8 to ON position.

If the converter requires a margin trim down, set the SW3_3 to ON position.

If the converter requires a margin trim up, set the SW3_4 to ON position.

Please refer to the SW3 Function table.

SW3 Function table

Subdivide switch No. Function

SW3_1 Voltage trim up

SW3_2 Voltage trim down

SW3_3 Resistor margin trim down

SW3_4 Resistor margin trim up

SW3_8 Resistor trim up

Note:

1. The subdivide switch of SW3_1~4 must not be ON at the same time.

2. For the SW3_5~7 use at NPA series, must set to OFF position.

7.2 Initial Power Up

1) Turn the power supply ON, set the current limit on DC source (refer to specification of

either converter) and increase the input voltage (use DVM2 to monitor the input voltage)

until it reaches the desired value.

2) Set the switch SW2 to power module ON.

3) The converter is now operating, which can be verified by observing the DVM3 (appropriate

value for the nominal output voltage) and channel 2 of the oscilloscope (appropriate value

for the nominal output voltage).

4) Set the switch SW2 to power module OFF.

8.0 Tests and Evaluation

8.1 Input Characteristics

8.1.1 Input Voltage Range and Under-Voltage Lockout

The DNS04xx Series of DC/DC converters will operate at full load from 2.4Vin to 5.5Vin for

5Vin (nominal) types. The DNS12xx Series DC/DC converters will operate at full load from

10Vin to 14Vin for 12Vin (nominal) types. The converters feature input under-voltage

protection, which will not allow the converter to start up unless the input voltage exceeds the

turn-on voltage threshold.

Test

1) Turn on the fan.

2) Set the input voltage to the desired operating point while monitoring DVM2.

3) Set the switch SW2 to the “ON or OFF” position to enable the converter. (See Item

7.1.5)

4) Test the input under voltage function while observing DVM2, DVM3 and channel 1 of the

oscilloscope. Increase the input voltage until the output of the converter reaches the

appropriate value. This will occur between 2.05 and 2.25 volts for 5Vin nominal and

between 9.0 to 10 volts for 12Vin nominal. Please refer to the appropriate converter data

sheet for the detailed specification.

8.1.2 No Load Input Current Test

1) Turn on the fan.

2) Set the input voltage to the desired operating point while monitoring DVM2.

3) Set the switch SW2 to the converter ON.

4) Remove/disable the output electronic load or resistive load.

5) Note the input current from DVM1.

6) The result is the No-Load Input current of the DC/DC converter.

The No-Load Input Current will be around 50 to 150 mA depending on the model under

evaluation. (Please refer to the data sheet for the detailed specification).

8.2 Output Characteristics

8.2.1 Line Regulation

Line Regulation Deviation is defined as the change in output voltage caused by varying the

input voltage over a specified range while the output load and temperature remain constant.

Test

1) Turn on the fan.

2) Set the output power to the desired operating point.

3) Set the switch SW2 to the converter ON.

4) Adjust the input voltage across the converter’s input range (refer to specified range) while

monitoring DVM2.

5) Note the maximum +/- deviation of the output voltage over the full range of the input

operating voltage (please refer to the data sheet for the detailed specification).

8.2.2 Load Regulation

Load Regulation Deviation is defined as the change in output voltage caused by varying the

output load current over the specified range (no load to full load) while the input voltage and

temperature remain constant.

Test

1) Turn on the fan.

2) Set the input voltage to the desired operating level while monitoring DVM2.

3) Set the switch SW2 to the converter ON.

4) Adjust the output load across the converter’s operating load range.

5) Note the maximum +/- deviation of the output voltage over the full range of the operating

load range (please refer to the data sheet for the detailed specification).

8.2.3 Output Ripple

Output Ripple is defined as the periodic AC component on the DC/DC converter’s output

voltage. The output ripple is measured in terms of peak to peak and RMS values, both done

with a specific bandwidth.

Test

1) Turn on the fan.

2) Set the switch SW2 to the converter ON.

3) Adjust the input voltage while monitoring DVM2 and set the output load to the full rated

load current.

4) Adjust channel 2 on the oscilloscope to be AC coupled at 4µS/Div and at 10mV/Div using

the 20 MHz bandwidth-limit option on the scope.

5) The output ripple of the DC/DC converter is measured at full load operating power.

8.2.4 Output Voltage Set-point Programming

(1) Output Voltage Set-Point Adjustment by external resistor

Output Voltage Set-point Programming can be carried out by using the external program

resistor connect between TRIM pin to ground to set output voltage set-point from 0.75Vdc to

5Vdc, the location can refer to the Evaluation Board Schematic (please refer to the data sheet

for more detailed specification). These test functions are divided into two types,

Rset of DNS04R series can be calculated by using the following equation:











−

−

=5110

7525.0

21070

Rset

Ω

For example, to program the output voltage of the DNS04 module to 1.8Vdc, below is the

calculation of Rtrim:

150045110

7525.08.1

21070 =











−

−

set

Ω

The table 1 provides the Rset value required for some standard output and the location on the

Evaluation board is R33.

Table 1.

Vo,set Rset (k

Ω

) R33 Recommend Value, R//R

0.7525 Open Open

1.2 41.973 44.2k//825k

1.5 23.077 23.7k//825k

1.8 15.004 15.4k//590k

2.5 6.947 7.15k//243k

3.3 3.160 3.16k//Open

Rset of the DNS12R series can be calculated by using the following equation:











−

−

=1000

7525.0

10500

Rset

Ω

For example, to program the output voltage of the DNS12 module to 3.3Vdc, below is the

calculation of Rset:

31221000

7525.03.3

10500 =











−

−

set

Ω

The table 2 provides the Rset value required for some standard output. The location on the

Evaluation board is R33.

Table 2.

Vo,set Rset (k

Ω

) R33 Recommend Value, R//R

0.7525 Open Open

1.2 22.464 23.7k//432k

1.5 13.047 14.0k//191k

1.8 9.024 9.53k//169k

2.5 5.009 5.23k//118k

3.3 3.122 3.16k//261k

5.0 1.472 1.5k//78.7k

Test

1. Put the resistor to program the desired output voltage set point by follow Table 1 and Table

2 for the standard output.

2. Set the input voltage to the desired operating level while monitoring DVM2.

3. Turn on the fan.

4. Set the enable switch SW2 to the “ON” position to enable the converter.

5. Adjust the output load across the converter’s operating load range.

6. Note the output voltage over the full range of the operating load range (please refer to the

data sheet for the detailed specification).

(2) Output Voltage Set-Point Adjustment by external voltage source

For DNS series, trim to Vo,set using an external voltage source, connect it between the

TRIM pin and GND pin. Please refer to the Table 3 and Table 4 as below for the

appropriate Vout. The value of Vtrim is specified as follows:

For DNS04xx series

()

7525.01698.07.0

−

×−= VoutVtrim

For example, to program the output voltage of a DNS04 module to 3.3 Vdc, Vtrim is

calculated as follows:

()

VVtrim 267.07525.03.31698.07.0

−

×−=

Table 3. : Vo,set adjustment range by use of external voltage source.

Product Part

Normal

Output Set

Voltage

(Vdc)

Vrim (V)

0.7525 Open

1.2 0.6240

1.5 0.5730

1.8 0.5220

2.5 0.4030

DNS04S0A0R06P A/B/C

DNS04S0A0R06N A/B/C

3.3 0.2670

For DNS12xx series

()

7525.00667.07.0

−

×−= VoutVtrim V

For example, to program the output voltage of a DNS12 module to 3.3 Vdc, Vtrim is

calculated as follows

()

53.07525.03.30667.07.0

−×−=Vtrim V

Table 4. : Vo,set adjustment range by use of external voltage source.

Product Part

Normal

Output Set

Voltage

(Vdc)

Vrim (V)

0.7525 Open

1.2 0.670

1.5 0.650

1.8 0.630

2.5 0.583

3.3 0.530

DNS12S0A0S06P A/B/C

DNS12S0A0S06N A/B/C

5.0 0.4167

8.2.5 Voltage Margining

Output voltage margining can be carry out by connecting a resistor from the Trim pin to ground

pin for trim up and connecting a resistor from Trim pin to Output pin for Trim down. The Rmargin-

up is for trim up and Rmargin-down is for trim down. (Please refer to the data sheet and

Evaluation Board Schematic for the detailed information).

A software tool for voltage margining calculation is available to ask for. The values of Rmargin-

up and Rmargin-down for a specific output voltage and margin percentage can then be figured

out. Please consult your local Delta Field Application Engineer or sales persons for additional

information.

Test

1) Connect a trim resistor for a desired voltage value (Please refer to Table 1 and Table 2).

2) Turn on the fan.

3) Adjust the input voltage while monitoring DVM2 and with output load set to the desired

operating point.

4) Set the enable switch SW2 to the “ON” position to enable converter.

5) Use SW3 (refer to Item 7.1_6) for Trim setup.

6) Note the voltage by observing DVM3.

7) Test the Load Regulation (refer to Item 8.2.2).

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Convertidor de medios de Delta Electronics

Delta Electronics

Delta Electronics PMF Series Manual de usuario

Delta Electronics

Delta Electronics PMT Series Manual de usuario

Delta Electronics

Delta Electronics Delphi S36SS Manual de usuario

Delta Electronics

Delta Electronics Delphi Series L48DB Manual de usuario

Delta Electronics

Delta Electronics Series DNM04 Manual de usuario

Delta Electronics

Delta Electronics HDS 1300 Manual de usuario

Delta Electronics

Delta Electronics NC15 Series Manual de usuario

Delta Electronics

Delta Electronics PMC Series Manual de usuario

Delta Electronics

Delta Electronics Series DNT12 Manual de usuario

Delta Electronics

Delta Electronics PMC-24V150W1AA Manual de usuario

Delta Electronics

Delta Electronics Series E48SB Manual de usuario

Delta Electronics

Delta Electronics PMC Series Manual de usuario

Delta Electronics

Delta Electronics Delphi S24SA Manual de usuario

Delta Electronics

Delta Electronics Series 240W Manual de usuario

Delta Electronics

Delta Electronics IFD8500 Manual de usuario

Delta Electronics

Delta Electronics Delphi H48SR Manual de usuario

Delta Electronics

Delta Electronics Delphi Q48DB Manual de usuario

Delta Electronics

Delta Electronics PMC Series Manual de usuario

Delta Electronics

Delta Electronics E36SR Manual de usuario

Delta Electronics

Delta Electronics PMT Series Manual de usuario

Delta Electronics

Delta Electronics Delphi E48SR Manual de usuario

Delta Electronics

Delta Electronics DNL Series Manual

Delta Electronics

Delta Electronics Delphi Q48SP Manual de usuario

Delta Electronics

Delta Electronics PMC Series Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario