Delphi Display Systems Endura 15X Manual de usuario
Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 1 of 19
Confidential Document:
Do not copy or distribute without written permission. Unpublished Work 20186 Delphi Display Systems, Inc. All rights reserved.
Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.
Title: Endura 15X OCS 15” Speaker Post Installation Instructions Doc Number: RDS-INS15XSSP
Revision: A
Department: Sales
Area:
Training
Approved and released Effective Date: 10/25/2016
Review Period: 365 days
Order Confirmation System (OCS)
Speaker Post Installation Instructions
Delphi Display Systems, Inc.
PROPRIETARY INFORMATION
Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 2 of 19
Confidential Document:
Do not copy or distribute without written permission. Unpublished Work 20186 Delphi Display Systems, Inc. All rights reserved.
Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.
This page intentionally left blank
Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 3 of 19
Confidential Document:
Do not copy or distribute without written permission. Unpublished Work 20186 Delphi Display Systems, Inc. All rights reserved.
Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.
Table of Contents
1
INTRODUCTION ............................................................................................................................................... 5
1.1
S
PEAKER
P
OST
M
OUNTING
O
PTION
................................................................................................................ 5
1.2
T
ECHNICAL
S
UPPORT
..................................................................................................................................... 5
2
REQUIRED TOOLS ........................................................................................................................................... 5
3
SITE PREPARATION ........................................................................................................................................ 6
3.1
S
ELECT
L
OCATION FOR THE
S
PEAKER
P
OST
................................................................................................... 6
3.2
C
ONDUITS
....................................................................................................................................................... 6
3.3
F
OOTING AND
A
NCHOR
B
OLTS
....................................................................................................................... 6
3.4
A
NCHOR
B
OLT
I
NSTALLATION
–
N
EW
I
NSTALLATION
.................................................................................... 7
3.4.1
Retrofit of an Existing OCS ................................................................................................................... 7
3.5
R
UNNING THE
E
LECTRICAL
W
IRING
–
N
EW
I
NSTALLATION
........................................................................... 8
3.6
R
UNNING THE
D
ATA AND
A
UDIO
C
ABLES
–
N
EW
I
NSTALLATION
.................................................................. 8
4
MOUNTING THE SPEAKER POST ................................................................................................................ 8
4.1
E
LECTRICAL
C
ONNECTIONS
–
C
ONDUIT
M
OUNTED
J
UNCTION
B
OX
............................................................. 11
4.2
E
LECTRICAL
C
ONNECTIONS
–
S
PEAKER
P
OST
M
OUNTED
J
UNCTION
B
OX
.................................................... 11
4.3
C
IRCUIT
B
REAKER
L
ABELING
....................................................................................................................... 13
4.4
S
PEAKER
I
NSTALLATION
U
SING
N
EW OR
E
XISTING
E
LEMENTS
.................................................................... 13
4.5
M
ICROPHONE
I
NSTALLATION
U
SING
N
EW OR
E
XISTING
E
LEMENTS
............................................................. 13
4.6
C
ONNECTING THE
A
UDIO
C
ABLES
................................................................................................................ 13
5
OCS DISPLAY MODULE INSTALLATION ................................................................................................ 14
5.1
I
NSTALLING THE
OCS
D
ISPLAY
M
ODULE IN THE
S
PEAKER
P
OST
................................................................. 14
5.2
C
ONNECTING THE
D
ATA
C
ABLE
(
S
) ............................................................................................................... 16
5.3
C
ONNECTING THE
P
OWER
C
ABLE
................................................................................................................. 17
5.4
S
ECURING THE
B
ACK
P
ANEL
........................................................................................................................ 17
6
CABLE CONNECTIONS INSIDE THE STORE .......................................................................................... 17
7
CHANGE HISTORY ........................................................................................................................................ 18
8
APPENDIX A - FOOTING AND CONDUIT SPECIFICATIONS................................................................. 1
Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 4 of 19
Confidential Document:
Do not copy or distribute without written permission. Unpublished Work 20186 Delphi Display Systems, Inc. All rights reserved.
Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.
Table of Figures
F
IGURE
1
–
A
NCHOR
B
OLT
K
IT AND
T
EMPLATE
............................................................................................................. 6
F
IGURE
2
-
C
OMPLETED
F
OOTING
................................................................................................................................... 7
F
IGURE
3
-
L
OCK ON
B
ACK OF
S
PEAKER
P
OST
............................................................................................................... 8
F
IGURE
4
-
S
ETTING THE
P
OST
........................................................................................................................................ 9
F
IGURE
5
-
E
XAMPLE OF
U
SING
S
HIMS
......................................................................................................................... 10
F
IGURE
6
-
E
NSURE
P
OST IS
L
EVEL
............................................................................................................................... 10
F
IGURE
7
-
L
OWER
N
IPPLE FOR
AC
E
LECTRICAL
C
ONNECTION
.................................................................................... 11
F
IGURE
8
-
I
NCOMING
AC
E
LECTRICAL
R
OUTED
I
NTO
J
UNCTION
B
OX
........................................................................ 12
F
IGURE
9
-
C
ONNECT
I
NCOMING
AC
P
OWER PER LOCAL CODE AND
NEC .................................................................... 12
F
IGURE
10
-
AC
C
ONNECTION
C
OMPLETE
,
J
UNCTION
B
OX
S
EALED
............................................................................. 12
F
IGURE
11
-
E
XAMPLES OF
P
ROPERLY
L
ABELED
C
IRCUIT
B
REAKER
............................................................................ 13
F
IGURE
12
-
S
PEAKER
A
SSEMBLY
I
NSTALLATION
........................................................................................................ 13
F
IGURE
13
-
D
ETAIL OF
A
LIGNMENT
A
NGLE
S
TOP
....................................................................................................... 14
F
IGURE
14
-
I
NSERT
E
NDURA
15X
AT AN ANGLE
.......................................................................................................... 14
F
IGURE
15
-
E
NDURA
15X
I
NSERTED
O
NTO
S
HELF
....................................................................................................... 15
F
IGURE
16
-
S
TRAPS
I
NSERTED
.
A
TTACH
2
N
UTS TO
S
ECURE
...................................................................................... 15
F
IGURE
17
-
T
IGHTEN
#10
N
UTS WITH
5/16"
D
RIVER
................................................................................................... 16
F
IGURE
18
-
W
ATERTIGHT
C
ONNECTION
...................................................................................................................... 16
F
IGURE
19
-
I
NSERT
P
OWER
C
ONNECTOR
..................................................................................................................... 17
F
IGURE
20
-
B
ACK
P
ANEL
............................................................................................................................................ 17
Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 5 of 19
Confidential Document:
Do not copy or distribute without written permission. Unpublished Work 20186 Delphi Display Systems, Inc. All rights reserved.
Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.
1 Introduction
This document describes the installation procedure for the Delphi Order Confirmation System (OCS) Speaker Post
and is used in conjunction with other installation manuals which vary based on specific customer or system
requirements. This manual covers only preparation for and installation of the speaker post; which includes installing
the microphone, speaker and OCS into the post.
1.1 Speaker Post Mounting Option
The Speaker Post has been designed as a free standing integrated mounting system for the 9330 Series displays and
audio system speakers. The Speaker Post will accommodate a wide variety of speaker systems in either full or half
duplex configurations. The Speaker Post is constructed of aircraft quality aluminum 6061 and has been designed to
be aesthetically pleasing as well as durable and easy to install.
1.2 Technical Support
For technical assistance, please contact:
Delphi Display Systems, Inc.
3160 Pullman St.
Costa Mesa, CA 92626
Toll Free: (800) 456-0060
Email: tec[email protected]
2 Required Tools
The following is a list of required tools. Some tools may not be required for all installations.
3/8" drive ratchet
3/4" deep well socket
3/4" open end wrench
10" #2 Philips screwdriver
5/16" nut driver
3/8” nut driver
Wire Strippers
Portable soldering iron
200' fish tape
Cordless Drill/Driver
Hammer
Multi-Meter
Hammer Drill - for use when installing new bolts in an existing concrete pad.
Level
Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 6 of 19
Confidential Document:
Do not copy or distribute without written permission. Unpublished Work 20186 Delphi Display Systems, Inc. All rights reserved.
Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.
3 Site Preparation
This section describes the steps necessary to properly prepare the site for installation of the Delphi OCS Speaker
Post. Please read the entire section before beginning any work. The following items must be completed prior to
installation of the OCS Speaker Post.
3.1 Select Location for the Speaker Post
The OCS Speaker Post has been designed so that the display is positioned at the optimum height for most vehicles
when the bottom of the speaker post is level with the top of the curb near the vehicle. Refer to Appendix A when
selecting a location for distance specs. The speaker post must be placed in a position where the customer can see
both the OCS and the menu board clearly. If the speaker and microphone are to be installed in the speaker post, be
sure to select a position where an optimal audio condition can be maintained. Consider the underground vehicle
detector (loop) also. The center line position in front of the speaker post must be within 18” of the loop. If it is not,
a new loop may be necessary.
3.2 Conduits
A minimum of three (3) conduits must be run to the OCS Speaker Post; one for a dedicated electrical circuit, one for
audio cables and another for the data cables. Ensure that the conduits will be centered in the bolt pattern. Refer to
Appendix A for detailed specifications.
3.3 Footing and Anchor Bolts
Before pouring the footing, make sure that all of the conduit has been run and is in the correct locations. Locate the
anchor bolt mounting kit and verify the following contents shown in the figure below.
Four (4) each ½” ‘J’ anchor bolts
Eight (8) each ½” zinc plated hex nuts
Eight (8) each ½” zinc plated flat washers
One (1) each anchor bolt template
Figure 1 – Anchor Bolt Kit and Template
Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 7 of 19
Confidential Document:
Do not copy or distribute without written permission. Unpublished Work 20186 Delphi Display Systems, Inc. All rights reserved.
Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.
3.4 Anchor Bolt Installation – New Installation
Install the ½” anchor “J” bolts into the template and secure with the ½” nuts and washers. This will insure the
alignment of the mounting bolts in the concrete. Pour the concrete footing and locate the anchor bolts in the correct
position using the alignment tool. Make sure to keep the anchor bolt threads clean and finish the surface of the
concrete as smooth and level as possible. A properly installed footing, anchor bolts, and conduits should resemble
the one in the picture below.
Figure 2 - Completed Footing
3.4.1 Retrofit of an Existing OCS
In many retrofit installations, existing slabs may be used to mount the OCS Speaker Post. The footing must be at
least 12” wide by 12” deep and of sufficient depth to support the OCS Speaker Post. It may be necessary to remove
existing anchor bolts and install new ones to match up to the base plate mounting hole pattern. Verify that the
existing conduits will be centered within the bolt pattern.
Some installations may have conduits that have been run outside the existing speaker post. In these cases, conduit
can be run into the back of the speaker post utilizing the provided “knock outs”. If the “knock outs” are not in the
correct position to be used, you may cut your own “knock out” in the bottom of the back of the speaker post. DO
NOT PUNCH A HOLE AND EXTEND THE CONDUIT. You must cut the bottom edge of the post out. If you
do not, it will not be possible to remove the speaker post without first removing the conduit from the post.
Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 8 of 19
Confidential Document:
Do not copy or distribute without written permission. Unpublished Work 20186 Delphi Display Systems, Inc. All rights reserved.
Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.
3.5 Running the Electrical Wiring – New Installation
The OCS Speaker Post must be wired to a dedicated circuit on an isolated ground with the Point of Sale (POS)
system. Pull the electrical wiring in accordance with NEC and local building codes. Terminate the electrical wiring
with a standard single-gang junction box.
3.6 Running the Data and Audio Cables – New Installation
The data cable is provided by Delphi Display Systems and is pre-terminated on the OCS end with a weather proof
connector. Pull the data cable through the appropriate conduit starting at the OCS end. Leave five (5) feet of cable
protruding from the end of the conduit. This will allow enough cable to route up through the speaker post and
connect to the back of the display module. Do not under any circumstances leave any more than 5’ of data
cable inside of the speaker post.
4 Mounting the Speaker Post
Remove the back panel of the Speaker Post by using the supplied key to unlock the back panel.
Figure 3 - Lock on Back of Speaker Post
Lock on back of post.
Key located inside front of
Speaker Post in a plastic
bag tie strapped to the
mounting bracket
Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 9 of 19
Confidential Document:
Do not copy or distribute without written permission. Unpublished Work 20186 Delphi Display Systems, Inc. All rights reserved.
Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.
Install the speaker post over the bolts and conduits. Level the base plate and fasten with four (4) ½” nuts. If the
footing is not level, the base plate can be leveled using the supplied leveling shims around the bolts between the
speaker post and footing. After the speaker post is level, secure the bolts with the nuts provided.
Figure 4 - Setting the Post
Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 10 of 19
Confidential Document:
Do not copy or distribute without written permission. Unpublished Work 20186 Delphi Display Systems, Inc. All rights reserved.
Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.
Figure 5 - Example of Using Shims
Figure 6 - Ensure Post is Level
Tabla de contenidos
