Dellonda Baridi DH178 Manual de usuario

Baridi 60cm Bridge Zone Induction Hob, 4 Zones, Boost

Function, 9 Power Settings, 2800W

Model No. DH178

Thank you for purchasing a Dellonda product. Manufactured to a high standard, this product will,

if used according to these instructions, and properly maintained, give you years of trouble free performance.

DH178 Issue: 3 21/10/22

www.dellonda.co.uk

Important Information

Please read these instructions carefully. Note the safe operational requirements, warnings & cautions. Use the product correctly and with care

for the purpose for which it is intended. Failure to do so may cause damage and/or personal injury and will invalidate the warranty. Keep these

instructions safe for future use.

Refer to

instruction

manual

Warning:

Hot

Surface

SPECIFICATION

Cable Length: ....................................................................... 1m

Colour: .............................................................................. Black

Installation:..................................................................... Built In

Number of Hobs:.......................................... 4/5 (Bridge Zone)

Power:.............................................................................2800W

Product dimensions:...................................590 x 520 x 60mm

Supply: ........................................................................220-240V

Surface: ............................................................. Ceramic Glass

Type: ...........................................................................Induction

SAFETY INSTRUCTIONS

• ELECTRICAL SAFETY

• Dellonda recommend that installation and repairs are carried out by a suitably

qualied electrician.

• WARNING! It is the user’s responsibility to check the following:

• Check all electrical equipment and appliances to ensure that they are safe before

using. Inspect power supply leads, plugs and all electrical connections for wear

and damage. If the product is used in the course of business duties, it must be

maintained in a safe condition and routinely PAT (Portable Appliance Test) tested.

• ELECTRICAL SAFETY INFORMATION: It is important that the following information is read and understood.

• IMPORTANT: The appliance must NOT be connected to the mains supply by means of a 13A plug and socket.

• This appliance must be wired into a 30A double pole switched fused spur outlet, having 3 mm contact separation

and placed in an easily accessible position adjacent to the appliance. It should not be located above the

appliance and no more than 1.25m away from it.

• The “blue” neutral wire must be connected to the terminal marked with letter (N) - the live wire (L1) must be

connected to the terminal marked with letter (L1) (220-240V 1N~). see Fig.1.

• Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.

• Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that

they are secure.

• The cable can be looped if necessary, but make sure that is not kinked or trapped when the hob is in position.

Care must be taken to avoid the cable being in contact with hot parts of the appliance.

• IMPORTANT: Ensure that the voltage rating on the appliance suits the power supply to be used and that the unit

is wired in accordance with these instructions.

• DO NOT pull the appliance by the power cable.

• DO NOT use worn or damaged cables.

• Ensure that any faulty item is repaired or replaced immediately by a suitably qualied electrician.

• GENERAL SAFETY

• The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge or they have been given supervision or instruction concerning use of the appliance in a safe way and understand the

hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• A steam cleaner is not to be used.

• Accessible parts may become hot during use. Young children should be kept well away when in use.

• DO NOT use abrasive products to clean the ceramic surface to avoid scratching it. Otherwise, severe failure might happen to the appliance.

• OPERATIONAL SAFETY

• DO NOT allow paper or cloth to come in contact with any heating element.

• It is specically designed for use when heating or cooking food. The use of corrosive chemicals in heating or cleaning will damage the appliance

and could result in injury.

• If food being prepared should ignite, switch off the hob and disconnect from supply power.

• Only use utensils that are suitable for use with ceramic hobs.

• WARNING! DANGER OF EXPLOSION! Liquids and other foods must not be heated in sealed containers since they are liable to explode.

• DO NOT allow any accessories or electric cables to contact the hot parts of the appliance.

• HOT SURFACES! RISK OF BURNS! During use the appliance becomes hot.

• WARNING! Accessible parts may become hot during use. Young children should be kept away.

• Never move racks or pans when they are hot. Wait until they cool.

Warning:

Can cause

Fire

Indoor use

Only

Warning:

Electricity

1800/2100W

1200W

1500W

1800/2100W 1800/2100W

2800W ZONE

g.1

• IMPORTANT! Always switch off the electricity supply at the mains during installation and maintenance.

• DO NOT use the ceramic hob until you have read this instruction manual.

• The ceramic hob is intended for household use only.

• Ensure that small items of household equipment, including connection leads, do not touch the hob as the insulation material of this equipment is

usually not resistant to high temperatures.

• DO NOT leave the ceramic hob unattended when frying. Oils and fats may catch re due to overheating or boiling over.

• DO NOT switch on the hob until a pan has been placed on it.

• DO NOT put pans weighing over 25kg on the hob.

• DO NOT use the ceramic hob in the event of a technical fault. Any faults must be xed by an appropriately qualied and authorized person.

• In the event of any incident caused by a technical fault, disconnect the power and report the fault to the service centre to be repaired.

• GENERAL INFORMATION

• This appliance is designed for domestic household use and must be built into a standard kitchen cabinet or housing unit.

• The appliance surfaces will become hot during use and retain heat after operation.

• Please dispose of the packaging material carefully. Packaging material can be dangerous to children.

• DO NOT allow cable to come into contact with the heating areas of appliance.

• DO NOT install the appliance next to curtains or soft furnishings.

• The appliance must be placed in such a way that the power supply is accessible at all times.

• Before connecting the appliance to the power supply, check that the power supply voltage and current rating corresponds with the power supply

details shown on the appliance rating label.

• Never use a damaged appliance! Disconnect the appliance from the power source and contact your supplier if it is damaged.

• Danger of electric shock! Do not attempt to repair the appliance yourself. In case of malfunction, repairs are to be conducted by suitably qualied

personnel only.

• To avoid damaging the cord, do not squeeze, bend or chafe it on sharp edges. Keep it away from hot surfaces and open ames as well.

• Lay out the cord in such a way that no unintentional pulling or tripping over it is possible.

• DO NOT open the appliance casing under any circumstances. Do not insert any foreign objects into the inside of the casing.

• Always operate the appliance on a level, stable, clean and dry surface. Protect the appliance against heat, dust, direct sunlight, moisture, dripping

and splashing water.

• CLEANING

• Always disconnect the power supply prior to cleaning the appliance. If the switched fused connection unit is difcult to reach, shut off the power

supply by using the corresponding circuit breaker at the distribution board.

• Clean the appliance thoroughly before rst use. The hob should be cleaned regularly and any food deposits removed.

• Never clean the hob surfaces by steam cleaning.

• The ceramic surface should only be cleaned with warm soapy water, using either a sponge or soft cloth. No abrasive cleaners should be used.

• Any stains that may appear on the ceramic surface will have originated from food splashes or spilt food, these splashes occur during the cooking

process. These could possibly be a result of the food being cooked at an excessively high temperature or being placed in cookware that is too

small.

• INSTALLATION

• ELECTRICAL CONNECTION

• Review and understand Safety Section 1 before installing this unit.

• Dellonda strongly recommend this work to be conducted by suitably qualied personnel only.

• Before connecting the appliance, make sure that the supply voltage marked on the Rating Plate corresponds with your mains supply voltage.

• WARNING: THIS APPLIANCE MUST BE EARTHED.

• IMPORTANT: The appliance must NOT be connected to the mains supply by means of a 13A plug and socket.

• This appliance must be wired into a 30A double pole switched fused spur outlet, having 3 mm contact separation and placed in an easily

accessible position adjacent to the appliance. It should not be located above the appliance and no more than 1.25m away from it. See Fig.1.

• The “blue” neutral wire must be connected to the terminal marked with letter (N) - the live wire ( L1) must be connected to the terminal marked

with letter (L1) (220-240V 1N~). see Fig.1.

• The mains cable must not touch any hot metal.

• Care must be taken to ensure that the temperature of the mains supply cable does not exceed 50°C.

• If the mains supply cable is damaged, then it must be replaced by an appropriate replacement.

• INSTALLING THE HOB INTO THE KITCHEN WORK SURFACE

• The kitchen area should be dry and aired and equipped with efcient ventilation. When installing the hob, easy access to all control elements

should be ensured.

• POSITIONING THE APPLIANCE SEE FIG.2 & FIG.3

• The kitchen units that are in direct contact with the

appliances must be heat-proof (min. 95°C).

• The appliance can be installed on a work surface

with a distance of between 30 and 40 mm and near

to walls which are higher than the work surface,

maintaining a minimum distance of 100 mm (see

g.3).

• Carry out all cutting of the unit and work surface

then carefully remove shavings or sawdust before

inserting the appliances.

• To ensure a correct ventilation of the hob please

comply with the dimensions shown in g.3.

• Minimum ventilation clearance requirements are

70cm above the hob, 5cm below the underside and

2cm from the rear (g.3).

• Make sure the surface is level and square and that

no part interferes with the space required for installation.

• Prepare the cut as indicated (see installation dimensions g.2, g.3).

• Hob requires a rectangular hole of 560mm wide by 490 mm deep.

• Refer to g.2 and g.3 for location .

• Apply the seal strip (supplied) to the underside edge of the hob, and leave approx. 3mm from the edge of the glass. DO NOT use silicone.

• Cut any excess and bring the two ends of the seal together so they match.

Fig.2

590 520

560

490

Seal

g.2

• Fix the brackets (4 pcs) on the front side and rear side by screw. Put the hob in the

cut-out cabinet, and center it. Ensure that the front edge of the hob is parallel to the

side edge of the work surface.

• IMPORTANT: You must observe the ventilation requirements shown in g.3.

• IMPORTANT: There are ventilation spaces around the outside of the hob. YOU

MUST ensure that these spaces are not blocked by the work top, when you put the

hob into position (see g.3).

• IMPORTANT: Do not use a silicon sealant to seal the appliance against the

aperture. This will make it difcult to remove the hob from the aperture in future,

particularly if it needs to be serviced.

• OPERATION

• CHOOSING THE CORRECT COOKWARE

• Only use cookware with a base suitable for induction cooking. Look for the induction

symbol on the packaging or on the bottom of the pan.

• You can check whether your cookware is suitable by carrying out a magnet test.

Move a magnet towards the base of the pan. If it is attracted, the pan is suitable for

induction.

• If you do not have a magnet:

• 1. Put some water in the pan you want to check.

• 2. Follow the steps under ‘to start cooking’.

• 3. If the Incorrect Pot icon does not ash in the display and the water is heating, the

pan is suitable.

• Cookware made by the following materials is not suitable: pure stainless steel,

aluminium or copper without a magnetic base, glass, wood, porcelain, ceramic, and

earthenware.

• DO NOT use cookware with jagged edges or a curved base.

• Make sure that the base of your pan is smooth, sits at against the glass, and is the same

size as the cooking zone. Always centre your pan on the cooking zone.

• OPERATION

• WARNING! IF A HEATING ZONE IS HOT, IT IS LABELLED . DO NOT TOUCH THE

SURFACE.

• HEATING

• To turn the unit on, touch the On/Off button. The unit will 'beep', all indicators will light up for

one second, go out and the unit will be in standby mode.

• Place a suitable pan on the cooking zone that you wish to use. Make sure the bottom of the

pan and the surface of the cooking zone are clean and dry.

• Select the heating zone to be used and select a heat setting by using the Increase /

Decrease button.

• The bridge zone function is activated by holding down the front and rear left hand zone

indicators at the same time.

• To cancel bridge zone mode, touch the front or rear left hand zone indicator. Each zone can

be run in boost mode, which can be selected by touching the power boost button.

• The hob has a power management system which is activated if too many hob elements are

running on high settings. Elements may reduce their set value or shut off automatically.

• NOTE: If no heat setting is selected, the hob will turn off within one minute. The heat setting

can be modied at any time during cooking.

• When you have nished cooking, select the zone and using the Decrease button return the

setting to '0'.

• TIMING

• The timer can be used to simply measure time elapsed or to turn off a zone once the set

time is reached. The timer can be set between 1 and 99 minutes.

• To measure time elapsed make sure the hob is turned on and no zone selection key is

activated (zone indication ‘-‘ is not blinking).

• NOTE: you can set minute minder before or after cooking zone power setting nished.

• Touch Timer key, “00” will show in the timer display and the right hand “0” will blink.

• Set the time by touching the “+” “-” control of the timer. To set beyond 9 minutes, press the

Timer key again and the left hand "0" will blink. Use the Increase / Decrease buttons to set

your required time.

• When the time is set, it will begin to count down immediately. The display will show the

remaining time.

• The buzzer will sound for 30 seconds and the timer indicator will show “- -” when the set

time has elapsed.

• To switch off one or more cooking zones rstly touch the heating zone selection control

that you want to set the timer for.

• Set the time required as above i.e. "+" or "-" and count down will begin.

• NOTE: A red dot will appear against the relevant Zone Indicator to indicate which zone or

zones are being timed.

• To cancel a Timer, touch the Zone control, touch the decrease control to set the timer to "0".

• CLEANING

• Always disconnect the power supply prior to cleaning the appliance. If the switched fused connection unit is difcult to reach, shut off the power

supply by using the corresponding circuit breaker at the distribution board.

• Clean the appliance thoroughly before rst use. The hob should be cleaned regularly and any food deposits removed.

• Never clean the hob surfaces by steam cleaning.

• The hob ceramic should only be cleaned with warm soapy water, using either a sponge or soft cloth. No abrasive cleaners should be used.

• Any stains that may appear on the hob will have originated from food splashes or spilt food, these splashes occur during the cooking process.

g.3

ICON PURPOSE

ON / OFF

INCREASE SETTING

CHILD LOCK

TIMER SELECTION

DECREASE SETTING

ZONE INDICATOR

INCORRECT POT

BRIDGE SELECTION

These could possibly be a result of the food being cooked at an excessively high temperature or being placed in cookware that is too small.

• You should select a cooking temperature and function that is appropriate for the food that you are cooking. You should also ensure that the food

is placed in an adequately sized dish and that you use the drip tray where appropriate.

PROBLEM SOLUTION NOTE

Everyday soiling on glass:

ngerprints, marks, stains left by

food or non-sugary spills on the

glass.

1. Switch the power to the hob off.

2. Apply a hob cleaner while the

glass is still warm (but not hot!).

3. Rinse and wipe dry with a clean

cloth or paper towel.

4. Switch the power to the hob back

on.

• When the power to the hob is switched off, there will be no ‘hot

surface’ indication but the cooking zone may still be hot! Take

extreme care.

• Heavy-duty scourers, some nylon scourers and harsh/abrasive

cleaning agents may scratch the glass. Always read the label to

check if your cleaner or scourer is suitable.

• Never leave cleaning residue on the hob: the glass may

become stained.

Boilovers, melts, and hot sugary

spills on the glass.

Remove these immediately with a

sh slice, palette knife or razor blade

scraper suitable for ceramic glass

hobs, but beware of hot cooking

zone surfaces:

1. Switch the power to the hob off at

the wall.

2. Hold the blade or utensil at a 30°

angle and scrape the soiling or spill

to a cool area of the hob.

3. Clean the soiling or spill up with a

dish cloth or paper towel.

4. Follow steps above for everyday

soiling on glass.

• Remove stains left by melts and sugary food or spillovers

as soon as possible. If left to cool on the glass, they may be

difcult to remove or even permanently damage the glass

surface.

• Cut hazard: when the safety cover is retracted, the blade in a

scraper is razor-sharp. Use with extreme care and always store

safely and out of reach of children.

Spills on the touch panel. 1. Switch the power to the hob off.

2. Soak up the spill.

3. Wipe the touch control area with a

clean damp sponge or cloth.

4. Wipe the area completely dry with

a paper towel.

5. Switch the power to the hob back

on.

The hob may beep and turn itself off, and the touch controls

may not function while there is liquid on them. Make sure you

wipe the touch control area dry before turning the hob back on.

PROBLEM POSSIBLE CAUSE SOLUTION

The hob cannot be

turned on.

No power. Make sure the hob is connected to the power supply and that it is

switched on.

Check whether there is a power outage in your home or area.

If you’ve checked everything and the problem persists, call a

qualied technician.

The touch controls are

unresponsive.

The controls are locked. Unlock the controls. See Operation section for child lock

instructions.

The touch controls are difcult

to operate.

There may be a slight lm of

Water over the controls or you

May be using the tip of your

Finger when touching the

Controls.

Make sure the touch control area is dry and use the ball of your

nger when touching the controls.

• TROUBLESHOOTING

The glass is being scratched. Rough-edged cookware.

Unsuitable, abrasive scourer or

cleaning products being used.

Use cookware with at and smooth bases. See ‘Choosing the right

cookware’.

See ‘Care and cleaning’.

Some pans make crackling or

clicking noises.

This may be caused by the

Construction of your cookware

(layers of different metals

Vibrating differently).

This is normal for cookware and does not indicate a fault.

The induction hob makes a low

humming noise when used on a

high heat setting.

This is caused by the technology of

induction cooking.

This is normal, but the noise should quieten down or disappear

completely when you decrease the heat setting.

Fan noise coming from the

induction hob.

Acooling fan built into your

Induction hob has come on to

Prevent the electronics from

Overheating. It may continue to run

even after you’ve turned the induction

hob off.

This is normal and needs no action. Do not switch the power to the

induction hob off at the wall while the fan is running.

Pans do not become hot and

appears in the display.

The induction hob cannot

Detect the pan because it is not

suitable for induction cooking.

The induction hob cannot detect the

pan because it is too small for the

cooking zone or not properly centred

on it.

Use cookware suitable for induction cooking. See section

‘Choosing the right cookware’.

Centre the pan and make sure that its base matches the size of

the cooking zone.

The induction hob or a cooking

zone has turned itself off

unexpectedly, a tone sounds

and an error code is displayed

(typically alternating with one or

two digits in the cooking timer

display).

Technical fault. Please note down the error letters and numbers, switch the

power to the induction hob off at the wall, and contact a qualied

technician.

• ERROR CODES

ERROR CODE TYPE OF FAULT SOLUTION

E4/E5 Temperature sensor failure Please contact the supplier

E7/E8 Temperature sensor of the IGBT failure.

E2/E3 Abnormal supply voltage Please inspect whether power supply is normal. Power on after the

power supply is normal.

E6/E9 Bad induction hob heat radiation Please restart after the induction hob cools down.

Dellonda Limited

Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

01284 757575 [email protected] www.dellonda.co.uk

Environment Protection and Waste Protection and Electrical Equipment Regulations (WEEE)

Recycle unwanted packaging materials. When this product is no longer required, or has reached the end of it’s useful life, please dispose of it in

an environmentally friendly way. Drain any fluids (if applicable) into approved containers, in accordance with local waste regulations. Under the

Waste Batteries and Accumulators Regulations 2009, Dellonda would like to inform the user that this product contains one or more batteries. It

is our policy to continually improve products and we reserve the right to alter data, specifications and parts without prior notice. No liability is

accepted for incorrect use of this product. Guarantee is 12 months from purchase date, proof of which is required for any claim.

Information for domestic electric hobs

Model identiﬁcation

Type of hob

Number of cooking zones and/or

areas

Symbol Value Unit

4 zones

1 area

Heating technology (induction cooking zones

and cooking areas, radiant cooking zones,

solid plates)

For circular cooking zones or area: diameter

of useful surface area per electric heated

cooking zone, rounded to the nearest 5 mm

For non-circular cooking zones or areas:

length and width of useful surface area per

electric heated cooking zone or area,

rounded to the nearest 5 mm

Energy consumption per cooking zone or

area calculated per kg

Energy consumption for the hob calculated

per kg

ECelectric cooking

electric hob

Wh/kg

Electric hobs

187.2

Right down:16.0

Right up:18.0

Left down:191.1

Left up:185.7

Left bridge area:178.7

Right down:190.7

Right up:185.7

Induction

cooking

Left down:18.0

Left up:18.0

Left bridge area:18.0*38.0

DH178

Tabla de contenidos

Otros manuales de Quemador de dellonda

dellonda

dellonda DH131 Manual de usuario

Manuales populares de Quemador de otras marcas

Siemens

Siemens EX875KYV1E Hoja de especificaciones

AEG

AEG CERAMIC HOB 6010 K Manual de usuario

VALERA

VALERA CT 70A Manual de usuario

Zanussi

Zanussi ZGF 6420 Manual de usuario

Gaggenau

Gaggenau CI 273 Manual de usuario

G3 Ferrari

G3 Ferrari Energy Manual de usuario

Pkm

Pkm IN4B Manual de usuario

Award

Award H903BG Manual de usuario

Zanussi

Zanussi VCH 5005 RZ Manual de usuario

Miele

Miele KM 523 Manual de usuario

Hotpoint

Hotpoint IS67V8CCXT/E Manual de usuario

AEG

AEG HK854870XB Manual de usuario

Cookology

Cookology SEP600BK Manual de usuario

Bauknecht

Bauknecht Hob Manual de usuario

Zanussi

Zanussi ZGM 782 Manual de usuario

dipo INDUCTION

dipo INDUCTION DIBK218S Manual de usuario

Miele

Miele KM 5987 Manual de usuario

Miele

Miele KM 360 G Manual de usuario

dellonda baridi DH178 Manual de usuario

Manuales populares de Quemador de otras marcas