Pay particular attention when handling wheel-mounted machines, which have to be moved by hand once they are on the ground.
To prevent any risk of crushing, only move the machine by pushing it, never by pulling it, so that nobody can ever come to be in the path of the
machine as it moves. Anyone handling the machine must be supervised by another person uninvolved in the procedure, who shall keep a
constant watch to ensure that no obstacles or persons get in the machine's way and no other hazardous situations occur. This supervisor must
promptly alert the person moving the machine of any hazards so that the machine can be stopped immediately.
!The surface on which the machine slides, like the surface on which it is used, must meet all the essential safety requirements: it must be perfectly
horizontal and smooth, with nothing to interfere with the machine's movements. Check in advance to ensure that the whole distance to cover with
the machine meets all the above-mentioned requirements. Make sure that the sliding and supporting surfaces have a load-bearing capacity
sufficient to withstand the weight of the machine both empty and in use. Any discontinuity in the floor, e.g. expansion joints, grids and manholes,
must meet the specified requirements.
!Never, for any reason whatsoever, lift the machine by any hoisting points other than those indicated.
!Before the machine is used, it must always be immobilized using the fixing devices provided.
!The machine must be placed in an area accessible only to the OPERATORS and TECHNICIANS; failing this, it must be protected by a barrier
situated at least 2 m away from its outer edge. OPERATORS and TECHNICIANS may access the area where the machine is used providing they
are adequately clothed and equipped with the personal protective equipment specified by law (safety shoes, gloves, helmet, etc.). The
INSTALLER's personnel, or any visitors, must always be accompanied by an OPERATOR. Unauthorized personnel must never be allowed to
remain alone in the vicinity of the machine. The place of installation must be made inaccessible to children.
!OPERATORS shall restrict themselves to taking action on the machine's controls, so they must not open any of the panels, except for the one for
accessing the controls (if any).
!The INSTALLER shall restrict himself to taking action on the connections between the plant and the machine, so he must not open any panels, or
operate any controls.
!In all handling, usage, servicing or repairs on the machine, it is compulsory to comply with all current safety standards in the country where the
machine is used. This applies both to the equipment and to the operating methods adopted.
!Always disconnect the electric power supply before taking any action to install, service, repair or move the machine. This is of fundamental
importance to prevent the risk of death, severe injury and extensive damage to the plant.
!In certain stages of normal use, some of the containers comprising the machine are under pressure (e.g. the filter vessel, plenum chamber,
erosion-type dosing units, etc.). Never open such containers or remove any components connected to them before you have completely vented
said pressure. Venting must be done through the valves provided on the machine specifically for this purpose.
!Never move the machine during normal working cycles.
!Before each new working cycle, make sure that any mobile electric connections (power cords, plugs, etc.) are sound and efficient. If they show
any signs of damage, repairs must be made only by a specialized TECHNICIAN.
!Never take any action not mentioned in this manual under your own initiative.
!Connect the machine to the mains electric power supply according to the recommendations of this manual.
!Before starting the machine, check the efficiency of the earthing for the electric circuitry and machine frame or structure.
!Never use power cords of inadequate cross-section or provisional connections, not even briefly, and certainly not in the event of an emergency.
!Start the machine only after you have made sure of its perfectly safe connection to the systems providing the energy and anything else it needs to
function properly (mains electricity and water, compressed gas supply, water drainage network, etc.).
!Keep a safe distance from any mechanical parts in motion.
!Immediately report any alarms or the tripping of any automatic machine safety devices to the TECHNICIAN.
!Never manually reset the machine after an alarm or an automatic safety device has been tripped without first identifying and dealing with the
problem that caused them.
!Never remove the guards over moving parts while the machine is in operation.
!Before starting the machine, make sure all guards are correctly installed.
!Routinely perform all the scheduled servicing operations.
!Dispose of the packaging material for the machine at a suitable landfill, taking particular care over any film and plastic bags, which can expose
children to the risk of suffocation.
!Never release the processing waste deriving from the working process directly into the environment.
REGULATIONS FOR USING THE MACHINE IN THE FOODSTUFFS
SECTOR
The following considerations apply only to machines used with foodstuffs, i.e. destined to come into contact with products for human consumption:
!The machine in your possession has been designed and built to make it suitable for contact with foodstuffs, and fluids in particular. If in doubt
about the intended uses of your machine, refer to the relevant chapter in this manual.
!For logistic reasons related to the phases prior to its use (e.g. transport to the user's premises, storage in warehouses, etc.), it is impossible to
guarantee the delivery of the machine in conditions suitable to enable its immediate use without an accurate, preliminary sanitization. This is the
responsibility of the end user, who may have to comply with any established protocols, e.g. HACCP.
DEMOLITION AND DISPOSAL OF THE MACHINE
!At the end of its working life, the machine must be demolished and disposed of.
