Dell PowerEdge systems 6300 Manual de usuario

www.dell.com

™

Dell™ PowerEdge™ 63xx Systems

INSTALLING A MICROPROCESSOR

OR TERMINATOR CARD

Notes, Notices, Cautions, and Warnings

Throughout this guide, blocks of text may be accompanied by an icon and printed in

bold type or in italic type. These blocks are notes, notices, cautions, and warnings,

and they are used as follows:

NOTE: A NOTE indicates important information that helps you make better use of your

computer system.

NOTICE: A NOTICE indicates either potential damage to hardware or loss

of data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potentially hazardous situation which, if

not avoided, may result in minor or moderate injury.

WARNING: A WARNING indicates a potentially hazardous situation which,

if not avoided, could result in death or serious bodily injury.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Computer Corpo-

ration is strictly forbidden.

Trademarksusedinthistext:Dell,theDELLlogo,andPowerEdgearetrademarksofDellComputer

Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities

claiming the marks and names or their products. Dell Computer Corporation disclaims any propri-

etary interest in trademarks and trade names other than its own.

February 2000 P/N 78VER Rev. A00

support.dell.com Dell PowerEdge 63xx Systems—Installing a Microprocessor or Terminator Card 1

Dell™ PowerEdge™ 63xx Systems

Installing a Microprocessor or

Terminator Card

WARNING: The power supplies in your PowerEdge system may produce

high voltages and energy hazards, which can cause bodily harm. Only

trained service technicians are authorized to remove the computer cover

and access any of the components inside the computer. For more informa-

tion, see “Safety Instructions” in your system’s Installation and

Troubleshooting Guide.

This document updates information contained in your Dell PowerEdge system docu-

mentation. The guide-bracket assemblies, which hold the microprocessors or

terminator cards, have been redesigned. The following sections describe how to

remove or install a microprocessor or terminator card in a guide bracket assembly.

Removing a Microprocessor or Terminator

Card

Each microprocessor is contained within a single-edge contact (SEC) cartridge and

heat sink assembly. If your system has only one microprocessor, the remaining guide-

bracket assembly connectors must contain terminator cards.

To remove a microprocessor or a terminator card, perform the following steps.

CAUTION: The SEC cartridge and heat sink assembly can get extremely hot

during system operation. Be sure that the assembly has had sufficient time

to cool before you touch it.

CAUTION: When handling the SEC cartridge and heat sink assembly, take

care to avoid sharp edges on the heat sink.

WARNING: Before you perform this procedure, you must turn off the com-

puter and disconnect it from its AC power source. For more information, see

"Safety First—For You and Your Computer" in Chapter 7 in your system

Installation and Troubleshooting Guide.

2Dell PowerEdge 63xx Systems—Installing a Microprocessor or Terminator Card

1.Turn off the system, including any attached peripherals, and disconnect the AC

power cable from its power source.

NOTICE: See "Protecting Against Electrostatic Discharge" in the safety

instructions at the front of your computer’s Installation and Trouble-

shooting Guide.

2. Remove the computer cover.

See “Checking Inside the Computer” in your system’s Installation and Trouble-

shooting Guide for more information.

3. Remove the cooling shroud.

See “Checking Inside the Computer” in your system’s Installation and Trouble-

shooting Guide for more information.

4. Lift the latches on each end of the guide bracket assembly (see Figure 1). Pivot

the retention clips away from the guide bracket assembly, then slide the SEC car-

tridge or terminator card out of the guide bracket assembly.

Figure 1. Removing a Microprocessor or Terminator Card

latches (2)

guide-bracket assembly

retention clips (2)

heat sink

SEC cartridge

support.dell.com Dell PowerEdge 63xx Systems—Installing a Microprocessor or Terminator Card 3

Installing a Microprocessor or Terminator

Card

To install a microprocessor or terminator card, perform the following steps:

1.Slide the microprocessor or terminator card into the guide-bracket assembly until

the edge connector on the SEC cartridge or terminator card is firmly seated in the

connector on the system board.

Figure 2. Installing a Microprocessor or Terminator Card

2. Place the retention clips on each end of the guide bracket in the notches on the

ends of the guide bracket (see Figure 2), then close the two latches to secure the

microprocessor or terminator card in the bracket.

3. Replace the cooling shroud and computer cover.

See “Checking Inside the Computer” in your system’s Installation and Trouble-

shooting Guide for more information.

This completes the installation of your microprocessor or terminator card.

latches (2)

guide-bracket

assembly

retention clips (2)

notches (2)

heat sink SEC cartridge

4Dell PowerEdge 63xx Systems—Installing a Microprocessor or Terminator Card

www.dell.com

™

Printed in the U.S.A.

P/N 78VERRev. A00

*78VER*

Otros manuales para PowerEdge systems 6300

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Servidor de Dell

Dell

Dell PowerEdge R220 Manual de usuario

Dell

Dell DX6000G Manual de usuario

Dell

Dell Poweredge el Manual de usuario

Dell

Dell PowerEdge T20 Manual de usuario

Dell

Dell EMC VxFlex Ready Node Guía del usuario

Dell

Dell Force10 C150 Manual de usuario

Dell

Dell PowerEdge C8000XD Manual de usuario

Dell

Dell Olympus O-T400 Manual

Dell

Dell PowerEdge SC1435 Manual técnico

Dell

Dell Force10 S2410-01-10GE-24P Instrucciones de instalación y funcionamiento

Dell

Dell PowerEdge 1650 Manual técnico

Dell

Dell PowerEdge XE8640 Manual

Dell

Dell PowerEdge R610 Manual de usuario

Dell

Dell POWEREDGE 4300 Manual de usuario

Dell

Dell PowerEdge 2650 Instrucciones de funcionamiento y seguridad

Dell

Dell PowerEdge R510 Manual de usuario

Dell

Dell VEP4600 Manual de usuario

Dell

Dell 100 Series Manual

Dell

Dell PowerEdge 6950 Manual de usuario

Dell

Dell PowerEdge R320 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

Dell

Dell PowerEdge 4600 Manual de usuario

Dell

Dell PowerEdge 1655MC Manual de usuario

Dell

Dell POWEREDGE 1900 Manual de usuario

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario

Planet

Planet NAS-7410 Manual de usuario

Lenovo

Lenovo ThinkSystem SR635 V3 Manual de usuario

Fujitsu

Fujitsu PRIMERGY BX900 Manual de usuario

Asus

Asus RS700DA-E6 PS4 Manual de usuario