Dell D90D7 Manual de usuario
Installation Guide
Dell®Wyse D Class, Wyse X Class, and Wyse Z Class
Flash Upgrade Option Kit
Products: D90D7, D90DW, X90m7, X90mw, Z90D7, Z90S7, Z90DE7, Z90DW,
Z90SW
Issue: 031214
PN: 883884-31L Rev. C
Copyright Notices
© 2014, Dell Inc. All Rights Reserved.
This manual and the software and firmware described in it are copyrighted. You may not reproduce, transmit,
transcribe, store in a retrieval system, or translate into any language or computer language, in any form or by
any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, any part of this
publication without express written permission.
End User License Agreement (“License”)
A copy of the End User License Agreement is included in the software and provided for your reference only.
The License at http://www.wyse.com/license as of the purchase date is the controlling licensing agreement. By
copying, using, or installing the software or the product, you agree to be bound by those terms.
Trademarks
The Dell and Wyse logos and Wyse are trademarks of Dell Inc. Other product names mentioned herein are for
identification purposes only and may be trademarks and/or registered trademarks of their respective
companies. Specifications subject to change without notice.
You acknowledge that the Software is of U.S. origin. You agree to comply with all applicable international and
national laws that apply to the Software, including the U.S. Export Administration Regulations, as well as
end-user, end-use and country destination restrictions issued by U.S. and other governments. For additional
information on exporting the Software, see http://www.microsoft.com/exporting.
Ordering Information
For availability, pricing, and ordering information in the United States and Canada, call 1-800-438-9973 or visit
us at Dell.com. In all other countries, contact your sales representative.
Contents
1 Introduction 1
Kit Contents 1
Kit Warranty 1
Overview 1
Dell Technical Support 2
Related Documentation and Services 2
Dell Online Community 2
2 Installing D Class Flash 3
Requirements 3
Procedures 3
3 Installing X Class Flash 7
Requirements 7
Procedures 7
4 Installing Z Class Flash 9
Requirements 9
Procedures 9
5 Installing Firmware 13
Requirements 13
Procedures 14
Troubleshooting 19
USB Keys - Troubleshooting Boot Issues 19
SanDisk Cruiser Flash Drives - Troubleshooting Partition Issues 19
iv Contents
This page intentionally blank.
1Introduction
This guide provides step-by-step instructions to upgrade flash in the following
products:
•D Class:
·D90D7
·D90DW
•X Class:
·X90m7
·X90mw
•Z Class:
·Z90D7
·Z90S7
·Z90DE7,
·Z90DW
·Z90SW
Kit Contents
The kit includes a Flash module.
Kit Warranty
The warranty on this kit assumes the remaining months of warranty of the thin client in
which it is installed, or for 90 days, whichever is greater. Installation of this kit will not
void the factory warranty, however the user will be responsible for damage due to
improper installation.
Overview
To upgrade flash:
1. Perform a hardware installation (install new flash) by completing one of the
following (depending on your thin client class):
•"Installing D Class Flash"
•"Installing X Class Flash"
•"Installing Z Class Flash"
2. Complete "Installing Firmware."
2Chapter 1
Dell Technical Support
To access Dell technical resources, visit http://www.wyse.com/support. If you still have
questions, you can submit your questions using the Self-Service Center at
http://support.wyse.com/selfservice.html or call Customer Support at 1-800-800-9973
(toll free in U.S. and Canada). Hours of operation are from 6:00 A.M. to 5:00 P.M. Pacific
Time, Monday through Friday.
To access international support, visit http://www.wyse.com/global.
Related Documentation and Services
Fact Sheets containing the features of hardware products are available on the Dell Web
site. Go to http://www.wyse.com/products and use the Cloud clients tab to locate and
download the Fact Sheet for your hardware product.
Administrator and other documentation for your cloud client model are available at:
http://www.wyse.com/manuals.
Dell Online Community
Dell maintains an online community where users of our products can seek and
exchange information on user forums. Visit the Online Community forums at:
http://community.wyse.com/forum.
2Installing D Class Flash
This chapter contains information for users of Wyse D class thin clients who must
install new flash.
Requirements
•Small Phillips screwdriver
WARNING: Flash modules may be susceptible to damage by Electro-Static Discharge
(ESD). All industry-standard cautions should be followed to avoid ESD. Before you
remove or install a module, touch any metal part of the chassis and keep that contact
with the chassis during the installation process.
Procedures
CAUTION: Follow all precautions listed in the Quick-Start Guide that came with your
thin client for disconnecting and reconnecting the thin client.
1. Perform a proper shutdown of the thin client by closing all files and ending your
session, and then pressing the power button to turn off the thin client.
2. Unplug the power cord and power adapter, and remove any other cables from the
thin client, and detach the vertical foot.
3. Position the thin client horizontally, where the Wyse logo-side with four flat screws
is facing downward. Using the Phillips Screwdriver, remove the three screws from
the cover along the back panel edge as shown in Figure 1.
Figure 1 Removing the cover screws
4Chapter 2
4. Place your thumbs on the top surface of the opposite end where the three screws
were removed. With a continuous motion, push firmly downward and towards the
back panel (pushing down unlatches the hooks under the cover). The cover will
shift approximate 1/4 inch to hang over the back panel. (a) Grasp the overhanging
cover edge and raise the edge about 1-1/2 inches, and then (b) pull the cover out
towards the back panel at the same angle to free the opposite end of the cover from
the remaining hooks, as shown in Figure 2.
Figure 2 Removing the cover
5. Remove the cover to expose the main-board shield.
Figure 3 Main-board shield
6. Using the Phillips Screwdriver, remove the five screws from the main-board shield
(four corner screws and one screw mid-way along the front edge). Remove the
main-board shield and unplug the speaker wire (red wire) to expose the main board
and Flash module as shown in Figure 4.
WARNING: Flash modules may be susceptible to damage by Electro-Static
Discharge (ESD). All industry-standard cautions should be followed to avoid ESD.
Before you remove or install a module, touch any metal part of the chassis and keep
that contact with the chassis during the installation process.
Installing D Class Flash 5
Figure 4 Main board and Flash module
7. Remove the existing flash module. Locate the flash module and use the Phillips
Screwdriver to remove its retaining screw as shown in Figure 5. Lift the flash module
out of the socket.
Figure 5 Removing the existing flash module
8. Install the new flash module in the reverse order of removing the original flash
module. Carefully screw down its retaining screw until it is secure.
9. Replace the speaker wire (plug in red wire) and the main-board shield (five screws).
10.Replace the cover in the reverse order as described in step 4 (align the cover screw
tabs with the screw holes and slide the cover toward the front of the thin client).
11., Attach the cover screws in the reverse order as described in step 3.
12.Connect the power cord and power adapter, attach any other cables to the thin
client, and then attach the vertical foot.
CAUTION: Do not turn on the thin client. The thin client is ready to re-image,
however the flash module does not contain an operating system. Turning on power
to your thin client without firmware will display the error message “NO OPERATING
SYSTEM FOUND.”
13.Continue with "Installing Firmware."
6Chapter 2
This page intentionally blank.
Este manual sirve para los siguientes modelos
8
Tabla de contenidos
Otros manuales de Servidor de Dell
Dell
Dell PowerEdge 2800 Manual
Dell
Dell PowerEdge R410 Manual de usuario
Dell
Dell PowerEdge C6320 Manual de usuario
Dell
Dell PowerEdge Cluster SE500W Guía
Dell
Dell EMC PowerEdge XR11 Manual
Dell
Dell PowerEdge FD332 Manual de usuario
Dell
Dell POWEREDGE SC440 Manual de usuario
Dell
Dell PowerEdge 850 Guía
Dell
Dell PowerEdge UPS 500T Manual de usuario
Dell
Dell PowerEdge R210 II Guía de inicio rápido
Dell
Dell PowerEdge 2650 Instrucciones de funcionamiento y seguridad
Dell
Dell PowerEdge 2550 Manual de usuario
Dell
Dell EMC PowerEdge C6525 Manual
Dell
Dell PowerEdge R730 Guía de inicio rápido
Dell
Dell PowerEdge SP 575-2 Guía
Dell
Dell PowerEdge R805 System Manual de usuario
Dell
Dell DX6000G Manual de usuario
Dell
Dell PowerEdge C6220 Manual de usuario
Dell
Dell PS-M4110 Manual de usuario
Dell
Dell PowerEdge R920 Guía de inicio rápido
