Dell 6100 Instrucciones de instalación

'HOO



3RZHU(GJH



6\VWHP

0,&52352&(66255(3/$&(0(17

arnings, Cautions, and Notes

Throughout this manual, there may be blocks of text printed in bold type or in

italic type. These blocks are warnings, cautions, and notes, and they are used as

follows:

NOTE: A NOTE provides helpful information about using the computer system.

WARNING: A WARNING indicates the potential for bodily harm and

provides instructions for how to avoid the problem.

CAUTION: A CAUTION indicates either potential damage to hardware

or loss of data and provides instructions for how to avoid the problem.

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden.

Trademarksusedinthistext:Dell,theDELLlogo,andPowerEdgeareregisteredtrademarksofDellComputerCorporation;IntelandPentiumare registeredtrademarks

of Intel Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer

Corporation disclaims any proprietary interest in trademarks and trade names other than its own.

August 1997 P/N 81655

Dell PowerEdge 6100/200 System Microprocessor Replacement 1

Dell

PowerEdge

6100/200 System

Microprocessor Replacement

his document provides the procedures for replacing the Intel®Pentium®Pro

microprocessor(s) in a Dell PowerEdge 6100/200 system. Unless otherwise

noted, each procedure assumes the following:

•You have performed the steps in “Precautionary Measures” that follows.

•You can replace or reinstall a part by performing the removal procedure in

reverse order unless additional information is provided.

•The system has BIOS Revision A05 or greater.

If the system has a different BIOS, follow the procedures in “BIOS

Upgrade” later in this document.

recautionary Measures

Before you perform any of the procedures in this chapter, take a few moments

to read the following warning for your personal safety and to prevent damage to

the computer system from ESD.

WARNING FOR YOUR PERSONAL SAFETY AND PROTECTION

OF THE EQUIPMENT: Only trained service technicians should per-

form the following procedures. Before you start to work on the

computer, perform the following steps in the sequence listed.

1. Turn off the computer and any attached peripherals.

2. Disconnect the computer and any attached peripherals from their

power sources to reduce the potential for personal injury.

3. Disconnect any communications cables.

4. Wear a wrist grounding strap, and clip it to any unpainted metal sur-

face on the computer chassis.

If a wrist grounding strap is not available, touch any unpainted

metal surface on the back of the computer chassis to discharge any

static charge from your body.

WARNING: The power supplies in this computer system produce high

voltages and energy hazards, which can cause bodily harm. Only trained

service technicians are authorized to remove the computer covers and

access any of the components inside the computer.

2 Dell PowerEdge 6100/200 System Microprocessor Replacement

IOS Upgrade

1. Insert the BIOS diskette that came in the replacement kit into drive A.

2. Turn on the system.

3. After the system completes the boot routine, follow the instructions on

the monitor.

4. After the message BIOS has been successfully installed

appears on the monitor, remove the diskette from drive A and follow

the instructions on the monitor to reboot the system.

WARNING: The system may have more than one power supply cable.

To reduce the risk of electrical shock, a trained service technician must

disconnect all power supply cables before servicing the system.

Dell PowerEdge 6100/200 System Microprocessor Replacement 3

omputer Cover

Figure 1. Keylocks on Computer’s Back Panel

1. Turn the left cover’s keylock on the back panel of the computer to the

unlocked position.

2. Loosen the three screws along the back edge of the left cover.

Figure 2. Computer Cover Removal

3. Slide the cover toward the back of the computer an inch or so. Then

grasp the top of the cover at both ends, and lift it straight away from the

chassis.

keylock

(unlocked

position) keylock

(locked

position)

screw (6)

4 Dell PowerEdge 6100/200 System Microprocessor Replacement

upport Panel

Figure 3. Support Panel Removal

1. Remove the left computer cover.

2. Remove the support panel.

Remove the two screws from the support panel and pull the back edge tabs

on the panel out of the slots in the chassis.

support panel

slot (2)

tab (2)

screw (2)

Dell PowerEdge 6100/200 System Microprocessor Replacement 5

icroprocessor and Terminator Module

Figure 4. Microprocessor and Terminator Module Removal

1. Remove the left computer cover.

2. Remove the support panel.

3. Remove the microprocessor or terminator module.

Grasp the module by the corners and carefully pull the module out until the

edge connectors are free from the system board connectors.

NOTES: Both microprocessor module connectors must be populated. The

secondary connector must have either another microprocessor module or a

terminator module.

Be careful not to touch components or the gold edge connectors on the

module.

memory module

secondary

microprocessor or

terminator module

primary

microprocessor

module

6 Dell PowerEdge 6100/200 System Microprocessor Replacement

4. On the new microprocessor module, check or set the jumper settings

according to those shown in Figure 5 and Table 1.

Figure 5. 200 MHz/1MB Microprocessor Module

CAUTIONS: All microprocessors must have the same processor

speed or the jumpers on all the microprocessor modules must be

jumpered to the speed of the lowest-speed microprocessor.

All microprocessors must have the same cache size.

All 200 MHz/1 MB microprocessors must be used on a microprocessor

module with Dell part number 95545.

All 200 MHz/1 MB microprocessors must be used in conjunction

with Dell BIOS Revision A05 or greater and Dell customer diagnos-

tics software 3.79D00 or greater. The BIOS and diagnostics software

are available through the Dell bulletin board service (BBS) and the

Dell Web site at www.dell.com.

If a Dell customer diagnostics diskette is included with your system,

use the diskette instead of the Dell Server Assistant CD.

For microprocessor modules with one microprocessor, populate the

PROCESSOR 1 socket first.

Dell PowerEdge 6100/200 System Microprocessor Replacement 7

Table 1. Microprocessor Module Jumper Settings

Jumper Setting Description

J6B1 (default) A processor is not installed in the

adjacent slot, the SKIP setting. This

jumper is useful only when you are

using in-target probe (ITP).

A processor is installed in the adja-

cent slot, the INCLUDE setting.

J6D1 (default) A processor is not installed in the

adjacent slot, the SKIP setting. This

jumper is useful only when you are

using ITP.

A processor is installed in the adja-

cent slot, the INCLUDE setting.

J4D1 (default) A 200/66 MHz microprocessor is

installed. See Table 2 for jumper set-

tings by microprocessor speed.

J4B1 (default) The fan heat sink jumper. Always set

to the default (passive).

J1C1 The processor(s) cache is 1 MB.

The processor(s) cache is 512 KB.

Table 2. Processor Frequency Select

Frequency SEL0 (Pins 1-2) SEL1 (Pins 3-4) SEL2 (Pins 5-6)

150/60 MHz No jumper No jumper No jumper

180/60 MHz Jumper No jumper No jumper

166/60 MHz No jumper No jumper Jumper

200/66 MHz Jumper No jumper Jumper

NOTE: A jumper is set on any of the three PARK settings (Pins 7-8, 9-10, or 11-12) for any

frequency selected.

jumpered unjumpered

8 Dell PowerEdge 6100/200 System Microprocessor Replacement

icroprocessor and Heat Sink

The computer can have up to four microprocessors installed.

Figure 6. Microprocessor Configuration

To remove the microprocessor/heat sink assembly, follow these steps:

1. Remove the left computer cover.

2. Remove the support panel and the appropriate microprocessor module.

3. Remove the microprocessor securing clip from the microprocessor/heat

sink assembly (see Figure 7).

WARNING: The microprocessor chip can get extremely hot during

system operations. Be sure the chip has had sufficient time to cool

before touching it.

microprocessor

securing clip

thermal interface pad

(attached to the heat sink)

microprocessor

pin-1 corner of

socket

microprocessor

socket

front tab

heat sink

Otros manuales para 6100

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Servidor de Dell

Dell

Dell PowerEdge T430 Manual de usuario

Dell

Dell P570 Manual de usuario

Dell

Dell PowerEdge UPS 500T Manual de usuario

Dell

Dell EMC PowerEdge XE8545 Manual

Dell

Dell EMC VxFlex Ready Node 13G Manual de usuario

Dell

Dell EMC PowerEdge R540 Manual

Dell

Dell PowerEdge R610 Instrucciones de montaje

Dell

Dell poweredge VRTX Manual de usuario

Dell

Dell PowerEdge 300 Guía de referencia

Dell

Dell PowerEdge C6145 Manual de usuario

Dell

Dell PowerEdge T30 Manual de usuario

Dell

Dell DX6000G Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

Dell

Dell PowerEdge 1550 Manual de usuario

Dell

Dell External R720 T Guía de inicio rápido

Dell

Dell PowerEdge 1400SC Manual del propietario

Dell

Dell PowerEdge C6100 Manual de usuario

Dell

Dell PowerEdge R910 Manual de usuario

Dell

Dell PowerEdge 2950 Manual técnico

Dell

Dell PowerEdge R300 Manual de usuario

Dell

Dell PowerEdge PDU Managed LED Manual técnico

Dell

Dell PowerEdge R610 Manual de usuario

Dell

Dell ExaScale E600i Manual de usuario

Dell

Dell External OEMR R310 Guía de inicio rápido

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario

Planet

Planet NAS-7410 Manual de usuario

Lenovo

Lenovo ThinkSystem SR635 V3 Manual de usuario

Fujitsu

Fujitsu PRIMERGY BX900 Manual de usuario

Asus

Asus RS700DA-E6 PS4 Manual de usuario