Deliberant DLB2300 Manual de usuario

Wireless LAN Device Series

WLAN Outdoor Bridge

DLB2300/DLB2310/DLB2319

User Manual

Version. 1.0.0 (06.01.2006)

TABLE OF CONTENTS

PREFACE.........................................................................................................................................3

FCC Information.......................................................................................................................3

Installation Requirements..........................................................................................................4

CH 1. DEVICE INSTALLATION....................................................................................................5

PACKING LIST.................................................................................................................................5

CH 2. FIRST TIME CONFIGURATION........................................................................................5

BEFORE START TO CONFIGURE ........................................................................................................5

KNOWING THE NETWORK APPLICATION...........................................................................................6

ADVANCED SETTINGS ...................................................................................................................29

CONFIGURING WIRELESS SECURITY ..............................................................................................32

CONFIGURING AS WLANCLIENT ADAPTER...................................................................................35

QUICK START TO CONFIGURE .........................................................................................................35

CONFIGURING UNIVERSAL REPEATER............................................................................................38

CH 3. CONFIGURINGWDS.........................................................................................................40

WDS NETWORK TOPOLOGY...........................................................................................................40

WDSAPPLICATION.......................................................................................................................42

CH 4. ADVANCED CONFIGURATIONS .....................................................................................44

CONFIGURING LAN TO WAN FIREWALL........................................................................................44

PORT FILTERING ...........................................................................................................................44

IPFILTERING ................................................................................................................................44

MAC FILTERING...........................................................................................................................45

CONFIGURING PORT FORWARDING (VIRTUAL SERVER) ...................................................................45

MULTIPLE SERVERS BEHIND NATEXAMPLE: ..............................ERROR!BOOKMARK NOT DEFINED.

CONFIGURING DMZ .....................................................................................................................46

CONFIGURING WAN INTERFACE....................................................................................................46

STATIC IP .....................................................................................................................................48

DHCPCLIENT (DYNAMIC IP)........................................................................................................49

PPPOE.........................................................................................................................................49

PPTP ...........................................................................................................................................50

CONFIGURING CLONE MACADDRESS...........................................................................................51

CONFIGURING DHCPSERVER .......................................................................................................53

BANDWIDTH CONTROL .................................................................................................................54

QOS(QUALITY OF SERVICE)..........................................................................................................56

STATIC ROUTE SETUP....................................................................................................................60

DYNAMIC ROUTE SETUP ...............................................................................................................61

VPN PASS-THROUGH ....................................................................................................................62

USING CLI MENU.........................................................................................................................62

THE SYSTEM MANAGEMENT .........................................................................................................64

SNMPAGENT ..............................................................................................................................65

FIRMWARE UPGRADE....................................................................................................................67

CONFIGURATION DATA BACKUP &RESTORE ..................................................................................68

AUTO DISCOVERY TOOL ...............................................................................................................69

Preface

FCC Information

Electronic Emission Notices

This device complies with CFR 47 Part 15 of the FCC rules.

Operation is subject to the following two conditions:

•This device may not cause harmful interference.

•This device must accept any interference received, including interference that may cause

undesired operation.

FCC Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to CFR47 Part 15. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a residential environment, not

withstanding use in commercial, business and industrial environment,. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

•Reorient or relocated the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different that to which the receiver is

connected.

•Consult the dealer or an experienced radio/TV technical for help.

Changes or modifications to this equipment not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

FCC Radiation Exposure Statement

To comply with FCC RF exposure requirements in section 1.1307, a minimum separation

distance of 0.4-meters (15.75-inches) is required between the antenna and all persons.

Antenna Installation

WARNING: It is installer’s responsibility to ensure that when using the outdoor antenna in the United

States (or where FCC apply), only those antennas certified with the product are used. The use of any

antenna other than those certified with the product is expressly forbidden in accordance to FCC

rules CFR47 part 15.204.

The installer should configure the output power level of antennas, according to country regulations and

per antenna type. Professional installation is required of equipment with connectors to ensure

compliance with health and safety issues.

Installation Requirements

This guide is for the networking professional who installs and manages the Deliberant

DLB-2300/DLB2310/DLB2319 outdoor product hereafter referred to as the “device”.

To use this guide, you should have experience working with the TCP/IP configuration

and be familiar with the concepts and terminology of wireless local area networks.

Note: Only those antennas that are of the same type with lesser gain than those

that are certified with these devices may be used legally by the installer!

The following antennas have been tested with the DLB23xx:

Microcom Technologies 19dbi Panel Antenna (Model: 24EI19-SAF)

Superpass 14dbi Panel Antenna (Model: SPLG22)

Hyperlink Technology 12dbi Omni Antenna (Model: HG2412U)

Ch 1. Device Installation

Packing List

Before you start to install the ODU, make sure the package contains the

following items

●Wireless Outdoor Bridge unit * 1

●Mounting Kit * 1

●Power Over Ethernet Kit * 1

Ch 2. First Time Configuration

Before Start to Configure

There are two ways to configure the device, one is through web-browser, and

the other is through Secure Shell CLI interface. To access the configuration

interfaces, make sure you are using a computer connected to the same

network as the device. The default IP address of the device is 192.168.2.254,

and the subnet-mask is 255.255.255.0.

The device has three operation modes (Router/Bridge/WISP). In bridge mode,

also known as AP Client, you can access the device by both WLAN (Wireless

Local Area Network) and wired LAN. And in router/WISP modes, the device

can be accessed by both WLAN and WAN. The default IP addresses for the

device are 192.168.2.254(for LAN), 172.1.1.1(for WAN), so you need to make

sure the IP address of your PC is in the same subnet as the device, such as

192.168.2.X (for LAN), 172.1.1.X (for WAN).

Please note that the DHCP server inside the device is default to up and

running. Do not have multiple DHCP servers in your network environment,

otherwise it will cause abnormal situation.

We also provide an auto-discovery tool which is for finding out the IP of the

device. In case, you’ve forgot the IP of the device or the IP of the device has

been changed, you can use the tool to find out the IP of the device even your

PC is not in the same subnet as the device is.

Knowing the Network Application

DLB2300/DLB2310/DLB2319 can act as the following roles, and it supports

WDS (Wireless Distribution System) function.

zAccess Point

zWDS (Wireless Repeater)

zBridge/Router

zWISP

zAP Client

The device provides 3 different operation modes and the wireless radio of device can

act as AP/Client/WDS. The operation mode is about the communication mechanism

between the wired Ethernet NIC and wireless NIC, the following is the types of

operation mode.

Router

The wired Ethernet (WAN) port is used to connect with ADSL/Cable modem and the

wireless NIC is used for your private WLAN. The NAT is existed between the 2 NIC

and all the wireless clients share the same public IP address through the WAN port to

ISP. The default IP configuration for WAN port is static IP. You can access the web

server of device through the default WAN IP address 172.1.1.1 and modify the

setting base on your ISP requirement.

Bridge

The wired Ethernet and wireless NIC are bridged together. Once the mode is selected,

all the WAN related functions will be disabled.

WISP (Wireless ISP)

This mode can let you access the AP of your wireless ISP and share the same public

IP address form your ISP to the PCs connecting with the wired Ethernet port of the

device. To use this mode, first you must set the wireless radio to be client mode and

connect to theAP of your ISP then you can configure the WAN IP configuration to

meet your ISP requirement.

The wireless radio of the device acts as the following roles.

AP (Access Point)

The wireless radio of device serves as communications “hub” for wireless clients and

provides a connection to a wired LAN.

APClient

This mode provides the capability to connect with the other AP using

infrastructure/Ad-hoc networking types. With bridge operation mode, you can

directly connect the wired Ethernet port to your PC and the device becomes a

wireless adapter. And with WISP operation mode, you can connect the wired

Ethernet port to a hub/switch and all the PCs connecting with hub/switch can share

the same public IP address from your ISP.

WDS (Wireless Distribution System)

This mode serves as a wireless repeater; the device forwards the packets to another

AP with WDS function. When this mode is selected, all the wireless clients can’t

survey and connect to the device. The device only allows the WDS connection.

WDS+AP

This mode combines WDS plus AP modes, it not only allows WDS connections but

also the wireless clients can survey and connect to the device.

The following table shows the supporting combination of operation and wireless

radio modes.

Bridge Router WISP

AP V V X

WDS V V X

Client V X V

AP+WDS V V X

Hereafter are some topologies of network application for your reference.

Bridge Mode

With

Bridge Mode

With

WDS + AP

Bridge Mode

Router Mode

With

WDS + AP

WISP Mode

Internet

Broadband

Modem

Examples of Configuration

This example demonstrates how to set up a network with different device

configurations. There are 2 DHCP servers (DEV1/DEV4) in the network to control

the IP configuration of 2 domains (192.168.2.x/192.168.3.x). Once the setting is

done, all the PCs can visit Internet through DEV1.

We assume all the devices keep the factory default setting. To make sure that user can

continuing press the rest button for more than 5 seconds to restore the factory default

setting.

The following descriptions show the steps to configure DEV1 to DEV5.

Configure DEV1:

1. Connect the ADSL modem to Ethernet port of device using Ethernet cable.

2. Access the web server (http://192.168.2.254) of device from the wireless

station.

3. Use Wizard page to setup device.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario