Deco Chef DGPST01BLK Manual de usuario
TABLE OF
CONTENTS
Contents Page
Parts Introduction 2
Pasta Molds 3
Technical Specifications 3
Before Usage 4
How to Use 5
Assembling the Pasta Maker 5
Disassembling the Pasta Maker 7
The Control Panel and Programs 9
Flour to Water Ratio Tables 11
Pasta Making Steps 12
Cleaning the Pasta Maker 14
Frequently Asked Questions 15
Tips on Making Better Pasta 17
Maintenance and Cleaning 18
Deco Chef Warranty 22
Thank you for choosing Deco Chef products.
We hope you enjoy the delicious recipes you
make with our Pasta Maker.
Parts Introduction
1. Mixing chamber cover
2. Mixing paddle
3. Mixing chamber
4. Extrusion pipe
5. Spiral rod
6. Mold
7. Mold head
8. Mold knob
9. Base
10. Mold storage compartment
11. Cutting, cleaning, and leveling tool
12. Water measuring cup
13. Flour measuring cup
Note: The extrusion pipe (4) holds a removable white, plastic
circular washer which is indicated in the above picture by the
red arrow. This washer may be detached for cleaning. After
washing, be sure to put plastic washer in place on the extru-
sion pipe (4). The Pasta Maker cannot operate properly with-
out this piece. 2
Pasta
Molds
3
Below are the interchangeable pasta molds for
your pasta making machine
1. Large fettuccine 2. Medium fettuccine
3.Small fettuccine 4. Thick spaghetti
5. Thin spaghetti 6. Ultra-thin spaghetti
7. Udon 8. Macaroni
9. Triangular 10. Open macaroni
11. Sliced noodle 12. Ultra-thick spaghetti
13. Dumpling wrapper
Technical Specifications
Model DGPST01BLK
Rating Voltage 120V/60Hz
Rating Power 260W
Capacity 1.1lbs
Weight 9.9lbs
Before
Use
• Before the first use of this Pasta Maker be sure to read all the
instructions carefully and keep them for future reference.
• Unpack the all supplied parts to make sure your Pasta Maker
is complete with all items listed above in the Parts Introduction
and Pasta Molds. If you find damage to the components, do not
use them. Contact Customer Service Department.
• There may still be some production residue on the product,
so be sure to thoroughly clean all parts and accessories to your
Pasta Maker before its first use.
• We recommend that you keep the product packaging for at
least 30 days in case the product needs to be put back into the
box and shipped.
• Always assemble the product properly before connecting it to
the power supply to prevent damage to the product.
• Switch off the power supply before assembling and disassem-
bling.
• Ensure the Pasta Maker’s voltage rate (120V/60Hz) matches the
voltage stated on the rating label.
• Place the product on a flat, dry surface.
4
HOW TO
USE
5
ASSEMBLING THE PASTA MAKER
1. Ensure the Base (9) of the Pasta Maker is on a flat, dry surface, and not plugged
into your power supply. Find your Mixing Chamber (3) and fix it in position on the
top of your Base (9). Insert Mixing Paddle (2) onto the motor shaft, or the small
insert hole at the top of the Mixing Chamber (3). Once the Mixing Paddle (2) is
inserted into the Mixing Chamber (3), gently rotate the Mixing Paddle (2) to fix it
in place.
2. Insert the Extrusion Pipe (4) into the front opening of the Mixing Chamber (3).
3. Insert the Spiral Rod (5) into the front opening of the Extrusion Pipe (4). Fix
into place.
4. Insert your Mold (6) of choice (i.e. Udon, Spaghetti, etc.) into the Mold Head (7).
Ensure you are placing the extruding head, or Mold (6), facing downward so that
pasta drops smoothly (See instructional diagram below). Then, install the Mold
Head (7) into the Spiral Rod (5).
5. Place the Mold Knob (8) over the Mold Head (7). Tighten the Mold Knob (8) by
turning it clockwise.
6. Put the Mixing Chamber Cover (1) on the top of the Mixing Chamber (3) and
Mixing Paddle (2). Secure tightly.
Note: 7
• Make sure the Mold Knob (8) has been fixed properly and tightly.
• The dough’s extrusion time is related to the shape of the mold. The finer and
smaller the hole, the longer it takes for the noodles or pasta to be extruded. It
may take about 3 minutes for ultra-thin spaghetti to be extruded.
ATTENTION: The extrusion mold can only be changed after the Pasta Maker has
been switched off.
6
HOW TO
USE
7
DISASSEMBLING THE PASTA MAKER
Turn off Pasta Maker and disconnect from power supply before disassem-
bling.
1. Unscrew the Mold Knob (8) by turning it counterclockwise.
2. Remove the Spiral Rod (5) and Mold Head (7) by pulling them directly out of
the front opening of the Mixing Chamber (3).
3. Pull the hook connecting the Mixing Chamber Cover (1) to the Mixing Cham-
ber (3) and left the edge of the cover to remove.
4. Gently remove the Extrusion Pipe (4) by pulling it directly forward and out of
the front opening of the Mixing Chamber (3).
5. Remove the Mixing Paddle (2) by pulling it upward from the motor shaft locat-
ed at the top of the Mixing Chamber (3).
6. Remove the Mixing Chamber (3) by pulling it forward from the Base (9).
8
HOW TO
USE
9
THE CONTROL PANEL AND PROGRAMS
Confirm/Cancel
When connected to the power supply, the machine will beep and display “----“.
The Pasta Maker will enter standby mode in the following situations:
• If any function buttons are pressed, it will display “ON” and enter standby mode
if the Pasta Maker is not operated within 60 seconds.
• The Pasta Maker will stop working and go into standby mode if “Confirm/Can-
cel” is pressed during operation.
Chewy Pasta/Fast Pasta/Dumpling Wrapper
• Select the desired function. The display light will blink. The Pasta Maker is now
on standby mode.
• The Pasta Maker starts operating when “Confirm/Cancel” is pressed.
• After the extrusion process is completed, the Pasta Maker will stop automatical-
ly, and the control panel will display “OFF” and emit a beeping sound to signal
the completion of this process. The extrusion process takes about 15 minutes.
Tabla de contenidos
Manuales populares de Máquina para hacer pasta de otras marcas
Keating Of Chicago
Keating Of Chicago Custom Pasta Gas System 0107 Manual de usuario
Viante
Viante CUC-26PM Manual de usuario
Emeril Lagasse
Emeril Lagasse Pasta & Beyond PM-01 Manual de usuario
Omcan
Omcan PM-IT-0080 Manual de usuario
KitchenAid
KitchenAid KSMPEXTA Manual de usuario
Weston
Weston 01-0201 Manual de usuario
