DECK DOLLY JD 2320 Manual de usuario
1
ASSEMBLY INSTRUCTIONS
(To be used with the following models)
JD 2320, 2520, 2720, 2305 and others
2
IMPORTANT!!
After assembly, please be sure to operate the Deck Dolly on level,
hard surfaces only. Standing the Deck Dolly in the upright
position on soft or uneven surfaces may lead to injury and/or
damage.
Assembly Instructions
1) Open packaging and inspect to ensure contents are complete.
2) Contents (for either model) should be as pictured below:
2 - 7” Tires
Bottom Cross Support, Tube,
and 4 Brackets with hardware.
2 - Base Plates with hardware
Upper Deck Support,
2 Brackets, & Hardware
Bracket length is determined by
model of dolly.
3
2 Uprights with end plugs.
2- JD 2x20 Brackets
Installs with 4 - 5/16” x 1 ¼” bolts
4
Preassemble the bottom cross support tube and brackets as shown with ¼ “x 2 ¼”
bolts while leaving the nuts loose.
3) Preassemble the Upper Deck Support as shown below with 4 1/2” nuts.
4) Preassemble the Base Plates and Tires as shown below. The regular nut should be on
the inside and the serrated nut should be to the outside of the base plate. Take care
to tighten the bolt and nuts to allow the tire to spin freely but not be loose on the
bolt. Use 2 ½” x 3 ¼” bolts with hex nut between tire and bracket and flange nut on
outside of plate.
5
5) Tap ends caps into Uprights as shown below.
6) Assemble the pieces as shown below hand tight with ¼”x2 ¼” bolts.
7) The Base Plate may be tightened when assembled as shown below with 5/16” x 1 ¼”
bolts.
6
8) Install the brackets as shown below. Depending on how your deck is set up, you
may have to install the brackets on the inside of the uprights or with the bottom
down.
9) With the Deck Dolly preassembled, lay the unit over the deck and align and insert the
J-hooks into the large holes. You may now tighten those bolts.
7
10) Align the Upper Deck Support into the front deck mount leaving about an 1/8” of
space between the tube and the top of the deck mount. This is to insure that when in
the upright position the weight of the deck is on the lower mounts. There are
multiple holes so insure that the bottom bracket is seated in the deck mount and
situate the top bracket at the proper holes. Tighten these bolts.
11) You should now align and tighten the lower cross support tube when the brackets
are centered in the lower deck mount.
12) Check all bolts for tightness before operating the Deck Dolly.
13) Please take care to watch the lower deck wheels when operating the Dolly for
the first time. You may have to raise and turn the wheels so they do not catch on
the ground and pull the deck off of the Dolly.
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Carrito para exteriores de DECK DOLLY
DECK DOLLY
DECK DOLLY JD300 Series Manual de usuario
DECK DOLLY
DECK DOLLY JD 3 Series Manual de usuario
DECK DOLLY
DECK DOLLY JD 1023E Manual de usuario
DECK DOLLY
DECK DOLLY AutoConnect JD 7 Series Manual de usuario
DECK DOLLY
DECK DOLLY JD4 5 Series Manual de usuario
DECK DOLLY
DECK DOLLY JD 7 Series Manual de usuario
DECK DOLLY
DECK DOLLY AutoConnect JD 1023E Manual de usuario
DECK DOLLY
DECK DOLLY Universal DeckDolly Manual de usuario
