Daza Pager 2 Manual de usuario

PAGER2 MANUAL 2016 0 905

CONTENTS

1. WHAT'S IN THE BOX ....................................................................................................................1

1) The pager ................................................................................................................................1

2) Cradle .....................................................................................................................................1

3) USB Cable................................................................................................................................1

2. BEFORE YOU BEGIN.....................................................................................................................2

2.1 DazaTools software for the Pager ....................................................................................2

3. INSTALL THE SOFTWARE IN 3 EASY STEPS....................................................................................3

Step 1: Download the software ...................................................................................................3

Step 2: Start the installation proces.............................................................................................3

Step 3: complete the installation process ....................................................................................4

4. CONNECTING THE PAGER TO DAZATOOLS ...................................................................................5

4.1 Step1: Connect the pager to the computer ......................................................................5

4.2 Step2: Connect the pager to DazaTools............................................................................5

4.3 DazaTools: Change back-up location ................................................................................6

4.4 DazaTools: Select LAnguage.............................................................................................6

5. ADDING AND REMOVING TRANSMITTERS (DazaTools) ................................................................7

5.1 Step1: Assign the transmitter with a recognisable name ..................................................7

5.2 Step 2: Select the type of alarm transmitter.....................................................................7

5.3 Step 3: Add the transmitter .............................................................................................7

5.4 To remove a transmitter ..................................................................................................8

6. SETTINGS ....................................................................................................................................9

6.1 The name of the pager.....................................................................................................9

6.2 Buzzer volume / Vibration mode......................................................................................9

6.3 Man down delay ............................................................................................................10

6.4 Security / PIN code ........................................................................................................10

6.5 Save a backup of the current configuration on the computer.........................................11

6.6 Install a backup configuration on a pager via the computer ...........................................11

7. LOG...........................................................................................................................................11

8. UPDATES...................................................................................................................................12

8.1 Check the version of the software on the pager .............................................................12

8.2 Install a software update on the pager...........................................................................12

9. CONFIGURE SETTINGS VIA THE PAGER ......................................................................................13

9.1 Switching the pager on ..................................................................................................13

9.2 Open the pager menu....................................................................................................13

9.3 Navigating through the menu and selecting options in the menu...................................13

9.4 Exiting the menu............................................................................................................14

9.5 Adjust the volume of the pager......................................................................................14

9.6 Switch vibration mode on or off.....................................................................................14

9.7 Add new transmitters via the pager ...............................................................................15

9.8 Remove Transmitters via the pager................................................................................16

9.9 Switch the pager On / OFF .............................................................................................16

9.10 Change the PIN code......................................................................................................17

10. USING THE PAGER .................................................................................................................18

10.1 Confirm receipt of the alarm signal................................................................................18

10.2 View the log in the pager ...............................................................................................18

10.3 ‘Empty battery’ alarm ....................................................................................................19

10.4 Transmitting with the Pager / Assistance .......................................................................19

11. SPECIAL SETTINGS .................................................................................................................20

11.1 Adjust screen resolution for DazaTools ..........................................................................20

1. WHAT'S IN THE BOX

1) THE PAGER

2) CRADLE 3) USB Cable

2. BEFORE YOU BEGIN...

We recommend that you charge the pager fully before

using it for the first time. This can be done with the

cradle that comes with the pager.

Place the bottom end of the pager in the cradle and

make sure that the contact points (F) are properly

connected to the cradle.

Then plug the adapter into the wall socket. The

‘Charging’ pictogram will appear on the display. Once

the pager is fully charged, the ‘FULL’ pictogram will

appear on the display.

Charging

Battery fully charged

2.1 DAZATOOLS SOFTWARE FOR THE PAGER

DazaTools is a program that has been developed to enable optimal use of the pager. This software

makes it easy to operate and manage the pager. So we recommend that you use the functionality

provided by the software as much as possible. This is also necessary so that further updates for the

pager can be installed. The software can be installed in three easy steps. You will need an internet

connection to download the software. For more information about the installation of DazaTools we

advise you to go to chapter 3: INSTALL THE SOFTWARE IN 3 EASY STEPS

3. INSTALL THE SOFTWARE IN 3 EASY STEPS

Attention!

•Please remove all previous versions of PagerTools before installing the latest version.

•Do not connect the Pager to the pc before finishing the DazaTools installation.

You can install the software in 3 simple steps. An internet connection is required to download the

software.

Minimum system requirements:

* Windows XP SP3 or higher

* XGA-monitor (Minimum Resolution 1024x768)

STEP 1: Download the software

You can download the software for the pager free

of charge from our website: http://www.daza.nl

The DazaTools software can be found in the Pagers

section of the Downloads page.

-Download the software onto your computer.

-Extract the files to a folder of your choice

on your computer.

-Make sure the Pager is NOT connected

while you are installing the software.

-Double click on the file Setup.exe.

Note.

You might want to ask your IT Department

to ensure that the software is correctly installed.

STEP 2: Start the installation proces

The software is now ready to be installed.

Click on ‘Next’.

STEP 3: complete the installation process

Follow all of the instructions on the screen and

complete the installation process.

During the installation all necessary drivers are

automatically installed.

The DazaTools pictogram will automatically appear

on your desktop once the installation process is

completed.

With some PC’s you will get an install screen for the

PL2303 USB driver. Here you can choose the option

REPAIR. Do not restart the pc when asked. Please

press NO and finish the Dazatools installation first.

Restart your pc after finishing the installation.

4. CONNECTING THE PAGER TO DAZATOOLS

Information about how to download and install the software can be found in chapter 3: INSTALL THE

SOFTWARE IN 3 EASY STEPS.

4.1 STEP1: CONNECT THE PAGER TO THE COMPUTER

The USB port can be found at the bottom of the pager

behind the USB port slide (H). To access the port you

need to push the port slide down.

The original USB cable supplied with the pager is the

only cable that should be connected to the USB port

(G) on the pager. Connect the other end of the USB

cable to the computer or laptop on which the

DazaTools software is installed.

4.2 STEP2: CONNECT THE PAGER TO DAZATOOLS

Make sure the Pager is turned on before starting the

DazaTools Program.

- To start the Pager, press the OK button for 5 seconds

until you hear a victory tune.

When the pager is connected to the

computer it will emit a beep and the

‘Connection’ icon will appear on the

pager display. All of the data on the

pager will now be synchronized with the computer.

Note!Do NOT disconnect the pager while the

synchronization process is in progress.

Unable to establish a connection?Check if the USB

cable is properly connected to the pager and the

computer or laptop. Then click ‘Connect’ in the Quick

Access Toolbar.

Once the synchronization process has successfully

completed the Home tab will appear on the screen

and you will see the serial number and name you have

assigned to the pager in the bottom right-hand corner.

4.3 DAZATOOLS: CHANGE BACK-UP LOCATION

After a successful installation and connection with the pager a folder will be created on your pc

located in "Your Documents" with a subfolder named Daza. This folder is used to store all settings

off your pager.

Change location

-Open DazaTools

-Click on "Settings"

-Click on the "Browse" button behind the Data

storage option

-Select your new location

4.4 DAZATOOLS: SELECT LANGUAGE

Select language

-Open DazaTools

-Make sure the Pager is connected

-Click on "Settings"

-Choose the language you want

-! please note: de language settings are not

yet saved into the pager and DazaTools,

please click on the save button in the tab

settings

-Both DazaTools and the Pager itself will be

shown in your selected language

5. ADDING AND REMOVING TRANSMITTERS (DAZATOOLS)

Once you have connected the pager to the

DazaTools software you can add and remove

Daza alarm transmitters. You can add a

transmitter in 3 easy steps. On the ‘Transmitters’

tab you will see a list of all of the transmitters

that have been added to the pager.

5.1 STEP1: ASSIGN THE TRANSMITTER WITH A RECOGNISABLE NAME

Click on a available row in the column headed

‘Name:’, were no transmitter is currently stored

and type in a recognizable name (up to 16

characters).

Note.

When the alarm transmitter transmits an

alarm the name you assigned to the transmitter

will appear on the pager display. So it is important

that you give the transmitter a recognizable name.

5.2 STEP 2: SELECT THE TYPE OF ALARM TRANSMITTER

In the second column headed ‘Type:’ select the

type of transmitter you want to add by clicking on

the type of transmitter in the drop-down menu.

5.3 STEP 3: ADD THE TRANSMITTER

Then click on the ‘Learn’button. The status of

the button will now change to ‘Wait?’.

Now transmit an alarm with the transmitter you

want to add. Once the transmitter has been

successfully added the pager will emit a ‘victory’

tone. The corresponding ID code and signal

strength will automatically be displayed.

The status of the ‘Wait...’ button will change to

‘Erase’. To

add several transmitters simply

repeat this procedure.

You will save the

transmitters into the pager by clicking on the

'Save'button. A progress bar will show that all

the transmitters are being stored in the pager

Tabla de contenidos

Manuales populares de Buscapersonas de otras marcas

Alpha

Alpha Elite Manual de usuario

LRS

LRS RX-E467 Manual de usuario

Bellman & Symfon

Bellman & Symfon Visit BE1470 Manual de usuario

unication

unication E3 Manual de usuario

Infostream

Infostream X5 Instrucciones de montaje

Motorola

Motorola BR850 Manual de usuario

ACE TELECOM

ACE TELECOM ACE-2040 Manual de usuario

Intek

Intek Allure Manual de usuario

Pocsag

Pocsag PG-2092P Manual de usuario

Motorola

Motorola Bravo classic Manual de usuario

Motorola

Motorola LS750 Manual de usuario

Alert Systems

Alert Systems HyperGuard MP10D Manual de usuario

Motorola

Motorola Talkabout T900 Manual de usuario

Motorola

Motorola Advisor Graphix CP1250 Manual de usuario

Radio Shack

Radio Shack 17-7040 Manual de usuario

PageOne

PageOne Advisor Graphix Manual de usuario

Syscall

Syscall Nttworks GP-210RT Manual de usuario

unication

unication G4 Manual de usuario