Davey AS Series Manual de usuario
Installation and
Operating Instructions
WARNING: Failure to follow these instructions and comply with all applicable
codes may cause serious bodily injury and/or property damage.
The installation of this product should be carried out by a person knowledgable
in swimming pool plumbing requirements following the installation instructions
provided in this manual.
Please pass these instructions on to the operator of this equipment.
Davey Peristaltic Pump
AS Series
2
Contents
1. Warnings and Tips..............................................................................................3
1.1 Proper use of the Pump ................................................................................3
1.2 Risks..............................................................................................................3
1.3 Toxic and/or Dangerous Liquid Dosage ........................................................4
2. Pump Description................................................................................................5
2.1 Parts Description...........................................................................................5
2.2 Buttons Description .......................................................................................6
3. Installation and Recommendation.....................................................................7
3.1 Recommendations ........................................................................................7
3.2 Accessories Mounting ...................................................................................8
3.2.1 Bracket ........................................................................................................8
3.2.2 Mounting of the Clamp ................................................................................9
3.2.3 Mounting of Injection Valve .........................................................................9
3.2.4 Mounting of the Probe on the Probe Holder..............................................10
3.2.5 Mounting description of Tube on the Injection Valve.................................10
4. Commissioning and Operation ........................................................................ 11
4.1 Calibration Procedure.................................................................................. 11
4.2 Settings .......................................................................................................12
4.2.1 Adjustment of the Set point .......................................................................12
4.3 Operating Principle......................................................................................13
5. Maintenance.......................................................................................................13
5.1 Replacement of the Peristaltic Tube............................................................13
5.2 Maintenance of the Electrode......................................................................14
5.3 Controller Winterising..................................................................................14
5.4 Probe Winterising........................................................................................14
6. Trouble Shooting...............................................................................................15
7. Davey Repair or Replacement Guarantee ......................................................16
3
1.Warnings and Tips
Please read the warning notices very carefully because they provide
important information regarding safety in installation, maintenance and use
of the pH pump.
• Keep this manual in a safe place, so that it will always be available for
further consultation
• The device complies with N° 89/336/CEE “electromagnetic
compatibility” and N°73/23/CEE “ low voltage ” and also the
subsequent modication N° 93/68/CEE
N.B.: This pump has been constructed in accordance with best practice.
Product life, electrical and mechanical reliability will be enhanced if it is
correctly used and regularly maintained.
WARNING Any intervention or repair to the internal parts of the pump must
be carried out by qualied and authorised personnel. The manufacturers
decline all responsibility for the consequences of failure to respect this rule.
1.1 Proper use of the Pump
The pump should be used only for the purpose for which it has been
expressly designed namely the dosing of liquids. Any different use is to
be considered dangerous. The pump should not therefore be used for
applications that were not allowed for in its design. In case of doubt, please
refer to the details listed within this document, or contact your point of
purchase or Davey Water Products for further information. The manufacturer
of this product will not be liable for damage deriving from improper,
erroneous or unreasonable use of the pump.
1.2 Risks
• After unpacking the pump, make sure that it is completely sound. In
case of doubt, do not use the pump and contact Davey
•The packing materials (plastic bags, polystyrene, etc.) should be kept
out of the reach of children: As they may constitute a potential source of
danger
• Before you connect the pump make sure that the voltage ratings
correspond to your particular voltage supply. You will nd this value on
the rating plates attached to the pump
• The electrical installation to which the pump is connected must
comply with the local standards enforced in the state or country under
consideration
4
Use of electrical equipment always implies observance of some basic
rules. In particular:
- Do not touch with wet or damp hands or feet.
- Do not operate the pump with bare feet (example: swimming pool
equipment)
- Do not leave the equipment exposed to atmospheric agents
- Do not allow the pump to be used by children or unskilled individuals
without supervision
• In case of breakdown or improper functioning of the pump, switch it
off, but do not touch. Contact Davey for technical assistance for any
necessary repairs and insist on the use of original spares. Failure to
respect this condition could render the pump unsafe to use
• When the Davey AS Series pump is not in use for a substantial period
of time, or use is to be discontinued, disconnect the unit from any power
supply
Before carrying out any service on the pump:
1) Disconnect the mains power from the unit and
2) Relieve all the pressure from the pump head or the injection tube
In the event of possible losses on the hydraulic system of the pump
(breakage of the O-ring, the valves or the hoses), stop the pump
immediately and contact Davey.
1.3 Toxic and/or Dangerous Liquid Dosage
To avoid risk from contact with hazardous liquids or toxic fumes, always
adhere to the notes in this instruction manual and wear protective
clothing (gloves, goggles & overalls).
• Follow the instructions of the dosing liquid manufacturer
• Check the hydraulic part of the pump and use it only if it is in perfect
condition
• Use only the correct materials for the tubing, valves and seals to suit
the liquid to be dosed: where possible shield the tubing with PVC
conduit
• Before disconnecting the metering pump, make sure to ush out and
neutralise the pump head with the proper reagent liquid
5
2.Pump Description
The Davey Peristaltic pump is characterised by its ability to measure pH
value (between 0 and 14) with its probe placed on the ltration system
that analyses the pool water.
Depending of the measured value, the pump will inject the required
amount of product needed to maintain the balance of the pool water.
2.1 Parts description
Here are the complete contents of the package you received. All parts
will be necessary for the proper operation of your device.
A. Peristaltic pump
B. 4 meters of PVC Cristal tube
C. Electrode/pH Probe & Protective Cap
D. Foot lter
E. Injection valve
F. Clamp DN50 x 2
G. Buffer solution pH7
H. Screws & Masonry plugs for wall mounting
I. Inline electrode holder
J. Shutter washer
A
Fig. 1
B
C D
E
F
F
H
G
I
J
6
2.2 Buttons Description
CAL
SET
pH -
1. Press SET to see and adjust the set point.
2. Press CAL allows calibration of the pH level associated to the SET
button to change the value of the set point
3. Value/level of pH in water
4. pH - unit of measure to determine pool water chemical level. pH level
should remain between 7.2 and 7.6
Fig. 2
1 2
3
4
7
3.Installation Recommendations
3.1 Recommendations
• Install the pump in a dry place and well away from sources of heat
and in environments not exceeding 45°C. The operating minimum
temperature depends on the liquid to be pumped, bearing in mind that it
must always remain in a liquid state
• Carefully observe any standards in force in your state, territory or
country, as to electrical installation regulations and requirements
• The Davey AS Series pump will be in operation only when your ltration
pump is running
WARNING
• It is important to keep a minimum distance of 200mm
between the probe “C“ and the injection valve “E”
• The injection valve “E” must be placed last in the pipework
hydraulic installation
• In the case of an installation with redox and pH regulation,
it is advised to put the two sensors side by side and the
pH injection before chlorine injection to minimise the risk of
scale deposition on the chlorine injection
• For optimal service life of your peristaltic pump tube, it is
advised not to exceed a pressure of 1 bar and under no
circumstances exceed a pressure of 1.5 bar
• The pH probe must be located before any other device
such as a heater or an electrolyser
Please refer to the enclosed Davey ChloroMatic or Sanitiser
Installation & Operating Instructions for the “Injection Valve”
and “pH probe” location and positioning.
8
3.2 Mounting the Pump
3.2.1 Bracket
• Use mounting accessories « H » to x the bracket of the pump
• Remove the bracket on the pump by sliding it down
• Locate the bracket in the space chosen and mark the holes
• Drill the holes as required
(3mm for timber walls & 6mm for masonry walls)
• Fix the bracket to the wall
• Slide and secure pump into the bracket
Fig. 4
pH Pump
Mounting
Bracket
9
3.2.2 Mounting of the Probe clamp
3.3.3 Mounting of Injection Valve
Fig. 5
Fig. 7
Fig. 6
Fig. 8
Oring
A nut
Put Teon tape
on threads
Next
Pierce the top wall of the pipe
work through the clamp:
- Ø 8mm for the injection valve
- Ø 14 mm for the electrode/pH
probe.
This assembly is xed on the pipe
work.
E
10
3.2.5 Mounting description of the Tube on the Injection Valve
Fig. 10
A nut
Disk brake
Washer seat
Oring
Bracket
A nut
The PVC tube
A nipple
3.2.4 Mounting of the pH Probe into the Probe Holder
After removing the protective cap from the probe, you need to insert all
the parts as shown in the Fig.9.
Once the probe has been constructed as indicated in Fig.9, tighten
the probe nut without crimping the probe body. Push the probe
approximately 20mm into the pipe work so that the probe tip is
approximately halfway into the pipe work. Connect the probe lead to
the BNC terminal on the pump. (Fig.10)
The hydraulic hose is placed in the same way on the foot lter and on
the pump.
1. Slide the tube through the nut
2. Put the tube at the bottom of the conical nipple
3. Screw the nut by hand onto the nipple
Fig. 9
Fig. 11
Tabla de contenidos
Otros manuales de Bomba de agua de Davey
Davey
Davey HS Series Guía del usuario
Davey
Davey HM Series Manual de usuario
Davey
Davey RainBank KRBCABS1/20 Manual de usuario
Davey
Davey Spa Power SP800 Manual de usuario
Davey
Davey SureFlo DSF750 Manual de usuario
Davey
Davey ProMaster VSD ECO Series Manual de usuario
Davey
Davey HS50-06 Manual de usuario
Davey
Davey Dynapond 7000 Manual de usuario
Davey
Davey microlene MCS Manual de usuario
Davey
Davey DynaDrive DD60-10 Manual de usuario
Davey
Davey HM Series Manual de usuario
Davey
Davey XP500H Manual de usuario
Davey
Davey PowerMaster Eco PMECO Manual de usuario
Davey
Davey QB Series Manual de usuario
Davey
Davey TotalFlo TF40J Manual de usuario
Davey
Davey CY/A Series Manual de usuario
Davey
Davey XF111SS Manual de usuario
Davey
Davey D10A Manual de usuario
Davey
Davey BT14-300 Manual de usuario
Davey
Davey Davey XP/T Manual de usuario
Manuales populares de Bomba de agua de otras marcas
Sykes AmeriPumps
Sykes AmeriPumps GP100M Guía de solución de problemas
DUROMAX
DUROMAX XP WX Series Manual de usuario
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Manual de usuario
Franklin Electric
Franklin Electric IPS Manual de usuario
Xylem
Xylem e-1532 Series Manual de usuario
Milton Roy
Milton Roy PRIMEROYAL Manual de usuario