Dauphin PHONE CUBE Manual de usuario

https://www.kctoolco.com/hazet-863p-1-4-reversible-ratchet/

REVERSIBLE RATCHET 1/4“ DRIVE FOR

CORNER SCREWS ON TOP TRAVERSE BEAMS

ALTERNATIVE : 5MM ALLEN KEY

TOOLS REQUIRED:

HARDWARE INCLUDED:

BOTTOM FEET FILLERS

SCREWS FOR DOOR

COVERS FOR DOOR FRAME HOLES

ROOF CLIPS TO SECURE CEILING

8MM HEX BOLT SCREWS TO SECURE

PANELS TO TOP TRAVERSE

DESK KIT THREADED INSERTS

AND LOCK NUTS

TO SECURE DESK TO PANEL

RUBBER MALLET FOR INSERTING PANELS

1/8 DRILL BIT FOR DOOR HOLES

CORNER SQUARE TO ALIGN FRAME

FLAT PALLET KNIFE TO FACILITATE PANEL INSTALL

SPIRIT/LASER LEVEL TO LEVEL THE UNIT

CLAMPS TO FACILITATE PANEL INSTALL

13MM FLAT WRENCH FOR LEVELING THE GLIDES OF STRUCTURE

8MM HEX BIT WITH EXTENSION FOR HEX BOLT SCREWS

6MM ALLEN KEY FOR ROOF CLIPS

PHILLIPS HEAD BIT FOR SCREWS FOR DOOR FRAME

TWO 9 FT. STEP LADDERS FOR INSTALLING ROOF & PANELSMOVING CART/DOLLY FOR TRANSPORTING PANELS,

ROOF, AND POSTS

TOP TRAVERSE BEAMS

VERTICAL POSTS

SQUARE FLOOR BASE

MAIN ELEMENTS OF SKELETON FRAME:

STANDARD PHONE CUBE PANELS:

TECH ACOUSTIC PANEL

(DESK|POWER) GLASS DOOR GLASS PANEL STANDARD

ACOUSTIC PANEL

Fabric faces are applied to both sides of each Acoustic Panel

Tech Panel includes a conduit for power wiring to go through and T-nuts for the Desk installation

The 1026 marked beams will be installed on

the door side (Front) and opposite rear side.

Desk and Power can be installed on the rear.

The 1028 marked beams will be installed on

the sides (left and right) of the Cube. If the desk

is to be installed on the left or right, the beam

with the cut out must be installed on the

desk + power side.

One of the top traverse beams in each size (1026 and 1028) will have a cutout for power wiring to go

through this beam and the Tech panel.

The Desk and Power Tech Panel is commonly installed on the side adjacent to the door hinges (left side),

but can also be installed on the rear or the right side.

LOCATION OF THE TECH PANEL FOR DESK AND POWER

POWER CUTOUT IN TOP TRAVERSE BEAM

1026mm

(NO CUTOUT)

(REAR WITH CUTOUT)

TRAVERSE BEAM POWER CUTOUTS

Assemble two parallel sides by securing vertical

posts A and Bwith a 1026mm top traverse beam as

shown above.

The TRAVERSE Beam for the DOOR PANEL must have

NO CUTOUT.

Connect the opposite goal posts using the 1028mm

beams.

ASSEMBLE THE SKELETON FRAME (DO NOT TIGHTEN SCREWS ALL THE WAY)

TOP TRAVERSE BEAMS TO VERTICAL

POSTS CONNECTION DETAIL

DO NOT TIGHTEN SCREWS!

Screws will be tightened firmly later

at step

TOP TRAVERSE BEAMS (TOP VIEW):

The screw

plates go IN the

vertical post.

A Ratchet with 5mm hex bit is

used to assemble the

TRAVERSE Beam.

TRAVERSE BEAM: WITH CUTOUT

TRAVERSE BEAM: NO CUTOUT

Lay down the square floor base in the exact desired location for the Telephone Cube. Ensure that the

door side is on the desired side and that the square base is placed face up, with countersink holes

facing up.

COUNTERSINK FACE UP

2LOCATE WHERE PHONE CUBE IS TO BE INSTALLED

The leveling glides of the Vertical

Posts go into the outer holes of the

skeleton base.

PLACE SKELETON ON FLOOR BASE & PREPARE UNIT FOR PANELS

INSTALL POWER SOURCE CABLE IN TECH PANEL IF POWER IS COMING FROM THE

FLOOR

Insert and feed the GST end of the cable up the conduit from the bottom of the panel.

DISREGARD THIS STEP IF THE POWER SOURCE IS LOCATED OUTSIDE THE CUBE

(CEILING, FLOOR OR WALL)

APPROX 33FT LONG

BOTTOM

TOP

GST

3 PIN GST

3 PIN

DISREGARD THIS STEP IF THE CONFIGURATION DOES NOT HAVE A TECH PANEL

INSTALL THE PANELS INTO SKELETON FRAME

Once panel is half way inside the frame,

use a clamp on the skeleton frame and the

panel frame to facilitate the process.

If the source of power is coming from

the floor, feed the GST cable through

the top traverse beam’s power cutout.

PER STEP

Insert the Tech Panel

from the bottom on an

angle, then fit the

sides and top into the

skeleton frame. Use a

flat pallet knife.

Install and tighten the screws to hold the

panel within the skeleton frame.

USE 8MM HEX BIT

WITH EXTENSION

Repeat these for all Panels.

INSTALL POWER SOURCE CABLE IN TECH PANEL IF POWER IS COMING FROM THE

FLOOR

Install the door handles onto the door. Ensure the handles are

positioned as pictured facing the front of the glass door.

Check that the door latch clicks when closing the door.

Install the door panel. Secure the door frame with two

hex bolt screws as previously done with the other panels.

PREPARE AND INSTALL THE DOOR

INSTALL THE PANELS INTO SKELETON FRAME 6

The door

handle

package will

be attached to

the glass door.

12Cut & take out the plastic strips

once the door frame is installed.

Black Plastic

Strips:

They keep the

door glass panel

in the door

frame during

assembly.

USE 8MM HEX BIT

WITH EXTENSION

1. Remove the

protective piece of

wood from the

bottom of the door

carefully by removing

both leveling glides.

2. Install the leveling

glides back onto the

door when finished.

Preparing the Door Panel

Installing the Door Panel

Adjust the Panel leveling glides and

Vertical Post leveling glides to ensure

that the whole structure is leveled in

all directions.

Close the door before leveling (until it

clicks).

Square all corners and firmly tighten all of the

corner screws and hex bolts located on top of

the panels and door. Check that diagonal

measurements from the inside are equal all

around.

8FINAL LEVELING OF STRUCTURE

ENSURE UNIT IS SQUARED/TIGHTEN

THE BOLTS

Make sure all glides are in

their respective holes before

leveling the structure.

IMPORTANT:

Leveling the unit from a flat stance

minimizes the amount of open space

between floor and posts/panels.

(IMPORTANT FOR ACOUSTICS).

Click

Use the 13mm Flat Wrench to

loosen/tighten the leveling glides

Adjusting Leveling Glides:

Loosening Leveling

Glide

Tightening Leveling

Glide

Loosening the

leveling glides will

RAISE the post.

Tightening the

leveling glides will

LOWER the post.

Otros manuales para PHONE CUBE

Tabla de contenidos

Otros manuales de Equipos de oficina de Dauphin

Dauphin

Dauphin Syncro-Automatic @Just magic2 Series Manual de usuario

Manuales populares de Equipos de oficina de otras marcas

silen

silen Space 2 Manual de usuario

Middle Atlantic Products

Middle Atlantic Products LD Series Manual de usuario

SHFL

SHFL DECK MATE BLACKJACK Manual de usuario

DROMEAS

DROMEAS LINE Manual de usuario

Siemens

Siemens HIPATH 2000 Manual de usuario

VITRA

VITRA Stefan Hürlemann Dancing Wall Manual de usuario

BISLEY

BISLEY Glide V2 Manual de usuario

fully

fully Haven Manual de usuario

Plus

Plus NF-20 Manual de usuario

OCEE DESIGN

OCEE DESIGN SASS-0100 Manual de usuario

NanaWall

NanaWall CSW75 Manual de usuario

Vivo

Vivo DESK V000C Manual de usuario

ABB

ABB 2TKA002145G1 Manual de usuario

PolyVision

PolyVision Flow Manual de usuario

MBM

MBM FC-10 Manual de usuario

Wiremold

Wiremold V2400 Series Manual de usuario

Vivo

Vivo PP-3-T072D Manual de usuario

BuzziSpace

BuzziSpace BuzziNest Booth Manual de usuario