Datalogic LYNX BT 432 Manual de servicio

Quick Reference Guide

www.scanning.datalogic.com

Lynx™ BT Readers

Datalogic Scanning, Inc.

959 Terry Street

Eugene, OR 97402

Telephone: (541) 683-5700

Fax: (541) 345-7140

Australia

Datalogic Scanning Pty Ltd

North Ryde, Australia

Telephone: [61] (2) 9870 3200

Fax: [61] (2) 9878 8688

France and Benelux

Datalogic Scanning Sarl

LES ULIS Cedex, France

Telephone: [33].01.64.86.71.00

Fax: [33].01.64 46.72.44

Germany

Datalogic Scanning GmbH

Darmstadt, Germany

Telephone: 49 (0) 61 51/93 58-0

Fax: 49 (0) 61 51/93 58 58

Italy

Datalogic Scanning SpA

Vimercate (MI), Italy

Telephone: [39] (0) 39/62903.1

Fax: [39] (0) 39/6859496

Japan

Datalogic Scanning KK

Shinagawa, Tokyo, Japan

Telephone: 81 (0)3 3491 6761

Fax: 81 (0)3 3491 6656

Latin America

Datalogic Scanning, Inc

Miami, Florida, USA

Telephone: (305) 591-3222

Fax: (305) 591-3007

Spain and Portugal

Datalogic Scanning Sarl

Sucursal en España

Madrid, Spain

Telephone: 34 91 746 28 60

Fax: 34 91 742 35 33

United Kingdom

Datalogic Scanning LTD

Watford, England

Telephone: 44 (0) 1923 809500

Fax: 44 (0) 1923 809 505

Datalogic Scanning, Inc.

959 Terry Street

Eugene, Oregon 97402

Telephone: (541) 683-5700

Fax: (541) 345-7140

documentation or the procedures described therein may be reproduced or

transmitted in any form or by any means without prior written permission of

Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic

Scanning”). Owners of Datalogic products are hereby granted a non-exclusive,

revocable license to reproduce and transmit this documentation for the

purchaser's own internal business purposes. Purchaser shall not remove or

alter any proprietary notices, including copyright notices, contained in this

documentation and shall ensure that all notices appear on any reproductions of

the documentation.

Should future revisions of this manual be published, you can acquire printed

versions by contacting your Datalogic representative. Electronic versions may

either be downloadable from the Datalogic website

(www.scanning.datalogic.com) or provided on appropriate media. If you visit our

website and would like to make comments or suggestions about this or other

Datalogic publications, please let us know via the "Contact Datalogic" page.

DISCLAIMER

Datalogic has taken reasonable measures to provide information in this manual

that is complete and accurate, however, Datalogic reserves the right to change

any specification at any time without prior notice. Datalogic is a registered

trademark of Datalogic S.p.A. in many countries and the Datalogic logo is a

trademark of Datalogic S.p.A. all licensed to Datalogic Scanning, Inc. All other

trademarks and trade names referred to herein are property of their respective

owners.

iii

CONTENTS

Updates and Language Availability.....................................................................iv

Using Lynx™ BT Series Readers........................................................................ 1

Charging the Batteries ........................................................................................ 2

Lynx™ BT Operation........................................................................................... 4

Lynx™ BT Configuration..................................................................................... 8

Operating Test .................................................................................................. 10

Lynx™ BT Default Configuration....................................................................... 11

Technical Features............................................................................................ 13

Troubleshooting ................................................................................................ 16

Patents.............................................................................................................. 17

Services and Support........................................................................................ 17

Warranty............................................................................................................ 17

Compliance....................................................................................................... 18

Hex Numeric Table ........................................................................................... 23

UPDATES AND LANGUAGE AVAILABILITY

UK/US

The latest drivers and documentation updates for this product are available on

Internet.

Log on to: www.scanning.datalogic.com

Su Internet sono disponibili le versioni aggiornate di driver e documentazione di

questo prodotto. Questo manuale è disponibile anche nella versione italiana.

Collegarsi a: www.scanning.datalogic.com

Les versions mises à jour de drivers et documentation de ce produit sont

disponibles sur Internet. Ce manuel est aussi disponible en version française.

Cliquez sur: www.scanning.datalogic.com

Im Internet finden Sie die aktuellsten Versionen der Treiber und Dokumentation

für dieses Produkt. Die deutschsprachige Version dieses Handbuches ist auch

verfügbar.

Adresse : www.scanning.datalogic.com

En Internet están disponibles las versiones actualizadas de los drivers y

documentación de este producto. También está disponible la versión en

español de este manual.

Dirección Internet: www.scanning.datalogic.com

LYNX™ BT

USING LYNX™ BT SERIES READERS

The Lynx™ BT (Lynx™ Bluetooth®) series reader is a wireless scanner

communicating in the 2.4 GHz ISM band and using the Serial Port Profile

(SPP).

The Lynx™ BT series reader, paired with an OM-1000 BT cradle, builds a

Cordless Reading System for the collection, decoding and transmission of

decoded data. OM-1000 BT can be connected to a Host PC through a USB,

RS232 or Wedge emulation cable. For details refer to the OM-1000 BT Quick

Reference Guide. OM-1000 BT also serves as a battery charger for Lynx™ BT.

Together with a Bluetooth®compatible remote device, Lynx™ BT also builds a

Cordless Reading System for the collection, decoding and transmission of

decoded data. The Bluetooth®compatible remote device can be a PC, PDA,

printer, etc with a built-in Bluetooth®device or with external Bluetooth®adapter

(i.e. a Bluetooth®dongle).

Using this Quick Reference Manual, you can initialize and start using your

Lynx™ BT reader with its default values for communicating with a

Bluetooth®device. To change the default values or for details about

general configuration commands, refer to the Lynx™ BT Reference

Manual on the configuration CD-ROM.

Thanks to its aiming system, Lynx™ BT visually indicates the reading area and

since Lynx™ BT is a powerful omni-directional reader, the orientation of the

symbol is not important.

AIMING SYSTEM

The Lynx™ BT reader uses an intelligent aiming system similar to those on

cameras. By partially pulling the trigger, the aiming system indicates a field of

view to be positioned over the code:

Aiming System

When you pull the trigger completely a red beam illuminates the code. If the

aiming system is centered and the entire code is within the aiming system, you

will get a good read. The field of view changes size as you move the reader

closer or farther away from the code.

DATALOGIC

Linear barcode 2D Matrix symbol

Relative Size and Location of Aiming System Pattern

The field of view indicated by the aiming system will be smaller when the

Lynx™ BT is closer to the code and larger when it is farther from the code.

Symbologies with smaller bars or elements (mil size) should be read closer to

the unit. Symbologies with larger bars or elements (mil size) should be read

farther from the unit.

Successful reading is signaled by an audible tone plus a good-read green led.

NOTE

If reading codes positioned on reflective surfaces, it may be

necessary to tilt the reader with respect to the code and/or set

the Camera Control parameters. For configuring the Camera

Control parameters refer to the Lynx™ BT Reference Manual

available on the CD-ROM.

CHARGING THE BATTERIES

By placing the reader into the C-1000 battery charger or the OM-1000 BT cradle

it is possible to charge the Lynx™ BT batteries. Make sure the charging LED

goes on.

The LEDs positioned on the battery charger signal the charge status, as

described in the following table:

LED STATUS

Charging Red On = the battery charge is in progress.

Batt Full Green On = the battery is completely charged.

LYNX™ BT

NOTE

The batteries must be charged at a temperature ranging from 0°

to 45 °C (+32° to +113 °F).

For further details about LED functioning refer to the C-1000 and OM-1000 BT

Quick Reference Guide.

CHANGING THE BATTERIES

To change the batteries of your reader, unscrew the

battery cover screw, replace the old battery pack with a

new one of the same type, then insert the cover onto the

handle and screw it back into place. (See the following

figures).

To turn on the reader, press the trigger.

WARNING

Do not incinerate, disassemble, short terminals or

expose to high temperature. Risk of fire, explosion. Use

specified charger only. Risk of explosion if the battery is

replaced by an incorrect type. Dispose of the batteries

as required by the relevant laws in force.

Power onCharging

Charge completed

Battery Cover Screw

DATALOGIC

POWERING THE C-1000/OM-1000 BT

CAUTION

Connections should always be made with power off!

Apply power to C-1000/OM-1000 BT by connecting a power supply unit to the

connector on the rear panel of the battery charger/cradle.

C-1000/OM-1000 BT is ready to charge Lynx™ BT Series readers with Li-Ion

batteries.

C-1000 Power Supply Connector

LYNX™ BT OPERATION

RADIO CONNECTION

In the Bluetooth®radio connection, the Lynx™ BT can operate as Slave or as

Master.

The green LED and/or the beeper always indicate the reader radio connection

status (see the table on page 5).

Power Supply

LYNX™ BT

STATUS INDICATORS

Lynx™ BT Series Reader LED Functioning

LED Behavior

Red at Power On, blinks briefly, then a beep occurs. Then, it turns off;

lights when a wrong read occurs;

lights briefly when the aiming system is enabled;

Green lights when a code has been read and decoded;

blinks during binding with OM-1000 BT (see OM-1000 BT Quick

Reference Guide for details);

single blink every 2 seconds when BT connection is active;

double blink every 2 seconds when BT connection is not active.

Lynx™ BT Series Reader Beeper Functioning

Beeper Behavior Condition

4 ascending tones during radio connection initialization.

4 descending tones upon radio disconnection.

2 beeps upon good read of a code, when paired to OM-1000

BT cradle.

1 beep upon good read of a code, when communicating with

a BT device.

DATALOGIC

OPERATING WITH BLUETOOTH®DEVICE

NOTE

The following procedures must be performed only if using the

Lynx™ BT reader with a BT device. If using the reader paired to

an OM-1000 BT cradle, you must follow the configuration

procedures as described in the cradle Quick Reference Guide.

To start using your Lynx™ BT reading system you must:

1. Have a compatible remote Bluetooth®device (with built-in Bluetooth®radio

or an external Bluetooth®adapter) ready to work. See your Bluetooth®

compatible device documentation.

2. Charge the Lynx™ BT battery using C-1000 charger as described in this

Quick Reference manual. A full charge takes up to 4 hours with Li-Ion

batteries.

3. Configure the reader as described in this Quick Reference manual under

"Lynx™ BT Configuration".

Lynx™ BT as Slave

A Lynx™ BT is Slave when it sends codes to a Master remote Bluetooth®

device such as a PC, Laptop, PDA, etc, which has initialized the

communication.

Once set as Slave, a Lynx™ BT reader requires no particular configuration for

communication, however some radio parameters can be set to increase system

performance and data transmission security, see the Lynx™ BT Reference

Manual on the configuration CD-ROM. At startup the reader can only wait for

the Master to initialize the radio communication.

The following is a general procedure recommended for Lynx™ BT Slave

applications:

1. Power up the remote Bluetooth®Master device (e.g. Laptop or PC).

2. Power up the Lynx™ BT reader within radio range (10 meters).

Any modifications to the radio configuration should be made at this time

before the radio connection takes place.

3. From the remote Bluetooth®Master device, execute the Discovery

procedure, (according to the procedure given in the documentation of

the Bluetooth®Master device), to recognize the Lynx™ BT reader(s)

within radio range.

4. Check that "Datalogic BT Device s/n: " is shown among the

discovered devices.

5. Request to open an SPP connection with Lynx™ BT, making sure to

disable any required PIN and/or pairing parameters. Lynx™ BT is

discoverable and connectable without any required PIN (default).

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Lector de código de barras de Datalogic

Datalogic

Datalogic DS8100A Manual de usuario

Datalogic

Datalogic PowerScan 9100 Series Manual de instalación y operación

Datalogic

Datalogic QuickScan QS2500 Manual de instalación y operación

Datalogic

Datalogic OM6010-R Guía del usuario

Datalogic

Datalogic Gryphon I GD441 Series Manual de usuario

Datalogic

Datalogic DS6300 Manual de usuario

Datalogic

Datalogic Magellan 800i Manual de instalación y operación

Datalogic

Datalogic Touch 65 pro Manual de usuario

Datalogic

Datalogic Gryphon I GD44XX Manual de usuario

Datalogic

Datalogic DS2100A Manual de usuario

Datalogic

Datalogic Magellan 1100i Manual de usuario

Datalogic

Datalogic Magellan 9500? Manual de instalación y operación

Datalogic

Datalogic PowerScan PD9530 Manual de usuario

Datalogic

Datalogic lynx bt Manual de usuario

Datalogic

Datalogic QuickScan QM2430-BK-433K2 Manual de usuario

Datalogic

Datalogic Touch 65 pro Manual de usuario

Datalogic

Datalogic PowerScan PBT950X Manual de instalación y operación

Datalogic

Datalogic PowerScan PD9130 Manual de usuario

Datalogic

Datalogic OM-GRYPHON Manual de usuario

Datalogic

Datalogic Gryphon I GM410X Manual de usuario

Datalogic

Datalogic PowerScan PD8530 Manual de usuario

Datalogic

Datalogic QuickScan Mobile Manual de usuario

Datalogic

Datalogic PowerScan RF SR Manual de usuario

Datalogic

Datalogic FireScan D141 Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario

Atid

Atid AT188N Plus Manual de usuario