Danfoss 176F6746 Manual de usuario

Description

The cable clamp kit is an option available for E3h and E4h

drives. The kit includes all parts required to install cable

clamps for mains, motor, and control wiring. E3h and E4h

drives with an RFI lter option (H4) include cable clamps as

standard equipment.

Kit Ordering Numbers

Kit number Kit description

176F6746 Cable clamp kit for E3h

176F6747 Cable clamp kit for E4h

Table 1.1 Numbers for the Cable Clamp Kit

Items Supplied

The cable clamp kit contains the following items. Refer to

Illustration 1.2.

Item Quantity

Cable clamp, 60 mm 6

Cable clamp, 16 mm 1

Cable bracket 1

Extension bracket 1

M6 hex nut 4

M8 hex nut 4

Table 1.2 Items Supplied in Cable Clamp Kit

Only qualied, Danfoss authorized personnel are allowed to

install the parts described in these installation instructions.

Handling of the drive and its parts must be done in

accordance with the corresponding operating guide.

WARNING

ELECTRICAL SHOCK HAZARD

VLT

FC series drives contain dangerous voltages when

connected to mains voltage. Improper installation, and

installing or servicing with power connected, can cause

death, serious injury, or equipment failure.

To avoid death, serious injury, or equipment failure:

•

Only use qualied electricians for the installation.

•

Disconnect the drive from all power sources before

installation or service.

•

Treat the drive as live whenever the mains voltage

is connected.

•

Follow the guidelines in these instructions and local

electrical safety codes.

WARNING

DISCHARGE TIME

The drive contains DC-link capacitors, which can remain

charged even when the drive is not powered. High voltage

can be present even when the warning LED indicator lights

are o. Failure to wait 40 minutes after power has been

removed before performing service or repair work can result

in death or serious injury.

•

Stop the motor.

•

Disconnect AC mains and remote DC-link power

supplies, including battery back-ups, UPS, and DC-

link connections to other drives.

•

Disconnect or lock PM motor.

•

Wait 40 minutes for capacitors to discharge fully.

•

Before performing any service or repair work, use

an appropriate voltage measuring device to make

sure that the capacitors are fully discharged.

Installation Instructions

Cable Clamp Kit for E3h/E4h Drives

VLT®FC Series FC 102, FC 103, FC 202, and FC 302

Removing the Terminal Cover

The lower cover panel and terminal cover at the bottom part of the drive are required to maintain the IP20/Chassis protection

rating. Remove the lower cover panel and terminal cover before installing the cable clamp kit. Refer to Illustration 1.1.

1. Unfasten 4 screws (T25) and remove the lower cover panel from the drive.

2. Unfasten 5 screws (T20) securing the terminal cover and remove the cover.

1 Lower cover panel 5 Slotted drive bracket

2 Terminal cover 6 Plastic gland plate

3 Grommet access hole for control wiring 7 Fastener point

4 Track guide 8 Keyhole opening

Illustration 1.1 Terminal Cover Disassembly/Assembly

Installation Instructions Cable Clamp Kit for E3h/E4h Drives

VLT

FC Series FC 102, FC 103, FC 202, and FC 302

Installing the Cable Clamps

Use the following steps to install the cable clamp brackets, 6 large cable clamps, and 1 small cable clamp. Use the large clamps for

mains and motor cables, and the small clamp for control wiring.

1. Position the 4 holes in the edge of the extension

bracket over the 4 threaded studs on the drive back-

channel.

2. Fasten 4 M8 hex nuts (T30), securing the extension

bracket to the studs.

3. Position the 4 holes in the corners of the cable

bracket over the 4 threaded studs on the front of the

extension bracket.

4. Fasten 4 M6 hex nuts (T25), securing the cable

bracket to the studs.

5. Tilt each cable clamp at a 45ºangle and insert the

hooks through any 2 holes in the bracket. Lower to a

horizontal position.

6. Insert a cable into each clamp and tighten the cable

adjustment screw to secure the cable.

1 M8 hex nut 6 Clamp adjustment screw

2Threadedstud 7Cableclamp,60mm

3 Extension bracket 8 Threaded stud

4 Cable clamp, 16 mm 9 M6 hex nut

5 Cable bracket 10 Key hole

Illustration 1.2 Cable Clamp Kit Overview

Installation Instructions Cable Clamp Kit for E3h/E4h Drives

VLT

FC Series FC 102, FC 103, FC 202, and FC 302

Installing the Terminal Cover

After installing the cable clamp kit, replace the terminal cover and lower cover panel using the following steps. Refer to

Illustration 1.1.

1. Tilt the front of the terminal cover downward until

the fastener points rest on the slotted drive brackets.

2. Make sure that the side panels of the terminal cover

are on the outside track guide.

3. Push the terminal cover until it is positioned against

the slotted drive bracket.

4. Tilt the front of the terminal cover upward until the

fastener hole in the drive aligns with the keyhole

opening in the terminal cover.

5. Secure the terminal cover with 2 screws (T20). Torque

to 2.3 Nm (20 in-lb).

6. Replace the lower cover panel and fasten with 4

screws (T25). Torque to 2.3 Nm (20 in-lb).

Illustration 1.3 E3h Drive with Cable Clamp Kit Installed

Installation Instructions Cable Clamp Kit for E3h/E4h Drives

VLT

FC Series FC 102, FC 103, FC 202, and FC 302

Cable Clamp Kit Dimensions for E3h

Illustration 1.4 Front and Side Views of E3h with Cable Clamp Kit

Installation Instructions Cable Clamp Kit for E3h/E4h Drives

VLT

FC Series FC 102, FC 103, FC 202, and FC 302

Cable Clamp Kit Dimensions for E4h

Illustration 1.5 Front and Side Views of E4h with Cable Clamp Kit

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on

order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss

Danfoss A/S

Ulsnaes 1

DK-6300 Graasten

vlt-drives.danfoss.com

*MI35U102*

MI35U102130R0815 04/2018

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accionamiento de CC de Danfoss

Danfoss

Danfoss VLT 5000 Series Manual de usuario

Danfoss

Danfoss VLT FC Series Manual de usuario

Danfoss

Danfoss VLT Micro Drive FC 51 Series Manual de usuario

Danfoss

Danfoss VLT AQUA Drive FC 202 Guía

Danfoss

Danfoss VLT HVAC Drive FC 102 Instrucciones de funcionamiento

Danfoss

Danfoss VLT FCM Series Manual de usuario

Danfoss

Danfoss VLT Midi Drive FC 280 Instrucciones de funcionamiento

Danfoss

Danfoss VLT CDS 803 Manual de usuario

Danfoss

Danfoss VLT AutomationDrive FC 301 Instrucciones de funcionamiento

Danfoss

Danfoss VLT MCB 115 Manual de usuario

Danfoss

Danfoss VLT HVAC Drive FC 102 Manual de usuario

Danfoss

Danfoss AME 23 Manual de usuario

Danfoss

Danfoss VLT CDS 803 Manual de usuario

Danfoss

Danfoss VLT Midi Drive FC 280 Manual de usuario

Danfoss

Danfoss ECdry 55 Manual de usuario

Danfoss

Danfoss FC103-110-250Kw Manual de usuario

Danfoss

Danfoss VLT MCA121 Guía

Danfoss

Danfoss VLT AutomationDrive FC 300 Manual de usuario

Danfoss

Danfoss VLT HVAC Drive FC 102 Manual de usuario

Danfoss

Danfoss FC 300 Manual de usuario

Danfoss

Danfoss VLT AutomationDrive FC 301 Instrucciones de funcionamiento

Danfoss

Danfoss VLT FC 103 Manual de usuario

Danfoss

Danfoss FC 300 Guía

Danfoss

Danfoss VLT HVAC Basic Drive FC 101 Manual de usuario

Manuales populares de Accionamiento de CC de otras marcas

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manual de usuario

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manual de lista de piezas

Chamberlain Garog

Chamberlain Garog D Series Manual de usuario

Parker

Parker PDS Series Manual de usuario

Festo

Festo DGC G Series Guía de configuración

Binks

Binks QS-5012-1-CE Manual de usuario

ABB

ABB ACQ580-01 Series Manual de instalación

YASKAWA

YASKAWA CANopen SI-S3 Manual de usuario

GE D20A6 Manual de usuario

Unex

Unex MC-D-250-1000-050W-TW Manual de usuario

Geckodrive

Geckodrive G213V Manual de usuario

ABB

ABB RSYC-01 Manual de usuario

Rockwell Automation

Rockwell Automation PowerFlex 700S Manual del propietario

WEG

WEG DeviceNet CFW500 Manual de usuario

Siemens

Siemens SINAMICS G Hoja de datos

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Instrucciones de funcionamiento

SOMFY

SOMFY JR RU 30 Manual de usuario

Beckhoff

Beckhoff AX8911 Manual del operador