Danfoss 176F3167 Guía del usuario

1 Overview

1.1 Description

Top fan kits are used with iC7 Series FA09–FA12 Frequency Converters and VLT FC®Series D3h–D4h and E3h–E4h Drives.

The top fan assembly in FA09–FA10 and D3h–D4h frames requires 1 fan. The top fan assembly in FA11–FA12 and E3h–E4h frames

requires 2 fans. Top fans are secured under a grill or within a single or double fan housing.

Top fan replacement kits contain all parts required to replace 1 fan.

1.2 Kit Numbers

Use these instructions with the following kits.

Table 1: Top Fan Kits for iC7 Series FA09-FA12 Frequency Converters

Kit number

Description

Frame designation

176F3167

Top fan IP20 DC 80x38 mm

FA09–FA10

176F6636

Top fan IP20 DC 120x38 mm 48 V DC

FA11–FA12

Table 2: Top Fan Kits for VLT®FC Series D3h–D4h and E3h–E4h Drives

Kit number

Description

176F3166

Top fan IP20 DC 80x25 mm

176F3167

Top fan IP20 DC 80x38 mm

1.3 Items Supplied

The following parts are contained in the kit.

Table 3: Items Supplied in Top Fan Kits

Item

Quantity

Fan

Installation instructions

Application Guide

Top Fan Kit for FA09-FA12/D3h-D4h/E3h-E4h

iC7 Series Frequency Converters and VLT® FC Series Drives

2 Installation

2.1 Safety Information

NOTICE

QUALIFIED PERSONNEL

Only qualified, Danfoss authorized personnel are allowed to install the parts described in these installation instructions.

Disassembly and reassembly of the frequency converter must be done in accordance with the service guide.

Use the standard fastener torque values from the service guide, unless the torque value is specified in these instructions.

WARNING

ELECTRICAL SHOCK HAZARD

Danfoss frequency converters contain dangerous voltages when connected to mains voltage. Improper installation, and instal-

ling or servicing with power connected, can cause death, serious injury, or equipment failure.

Only use qualified electricians for the installation.

Disconnect the frequency converter from all power sources before installation or service.

Treat the frequency converter as live whenever the mains voltage is connected.

Follow the guidelines in these instructions and local electrical safety codes.

WARNING

DISCHARGE TIME

The frequency converter contains DC-link capacitors, which can remain charged even when the frequency converter is not pow-

ered. High voltage can be present even when the warning LED indicator lights are off. Failure to wait the specified time after

power has been removed before performing service or repair work can result in death or serious injury.

Stop the motor.

Disconnect AC mains and remote DC-link power supplies, including battery back-ups, UPS, and DC-link connections to other

frequency converters.

Disconnect or lock the motor.

Disconnect any brake option.

Disconnect any regen/load share option.

Wait for the capacitors to discharge fully. The minimum waiting time is listed on the frequency converter label and also in the

following discharge time table.

Before performing any service or repair work, use an appropriate voltage measuring device to make sure that the capacitors

are fully discharged.

Table 4: Discharge Time

Frame

Minimum waiting time

D1h–D8h

20 minutes

Fx09–Fx10

20 minutes

E1h–E4h

40 minutes

Fx11–Fx12

40 minutes

Installation

Top Fan Kit for FA09-FA12/D3h-D4h/E3h-E4h

Application Guide

•

NOTICE

ELECTROSTATIC DISCHARGE

Electrostatic discharge can damage components.

Ensure discharge before touching internal frequency converter components, for example by touching a grounded, conduc-

tive surface or by wearing a grounded armband.

2.2 Top Fan Replacement

Select the fan replacement instructions based on the type of fan enclosure:

2.3 Removing the Top Fan and Grill.

2.5 Removing the Top Fan and Single Fan Housing.

2.7 Removing the Top Fan and Double Fan Housing.

2.3 Removing the Top Fan and Grill

To remove the top fan and grill, use the following steps. See Illustration 1.

Unfasten 2 screws (T25) and remove the front cover from the frequency converter.

Unplug the top fan cable connector.

Pull the top fan cable through the cable access hole, freeing it from the cabinet.

Remove 2 screws (T25) from opposite corners of the top fan grill.

Installation

Top Fan Kit for FA09-FA12/D3h-D4h/E3h-E4h

Application Guide

Lift the grill and top fan from the frequency converter.

e30bg393.10

Illustration 1: Top Fan with Grill

Screw (T25)

Top fan grill

Top fan

Top fan cable and connector

Top vent

Cable access hole

2.4 Installing the Top Fan and Grill

To install the top fan and grill, use the following steps.

Feed the top fan cable through the cable access hole on the top of the frequency converter.

Reconnect the in-line fan cable connector.

Position the fan on top of the frequency converter with the air direction arrows pointing upward and away from the unit.

Place the grill on top of the fan.

Fasten 2 screws (T25) in opposite corners of the grill, securing the top fan to the frequency converter.

Position the front cover on the frequency converter, and fasten with 2 screws (T25).

Installation

Top Fan Kit for FA09-FA12/D3h-D4h/E3h-E4h

Application Guide

2.5 Removing the Top Fan and Single Fan Housing

To remove a fan with a single fan housing, use the following steps. See Illustration 2.

Unfasten 2 screws (T25) and remove the front cover from the frequency converter.

Unplug the top fan cable connector.

Pull the top fan cable through the cable access hole, freeing it from the cabinet.

Remove 2 screws (T25) from the top fan housing.

Slide the fan housing and top fan out from under the retaining clips on top of the frequency converter.

e30bg394.10

Illustration 2: Top Fan with Single Fan Housing

Single top fan housing

Screw (T25)

Top fan

Top fan cable and connector

Retaining clip

Cable access hole

2.6 Installing the Top Fan and Single Fan Housing

To install the top fan and single fan housing, use the following steps.

Feed the top fan cable through the cable access hole on the top of the frequency converter.

Reconnect the in-line fan cable connector.

Place the top fan in the fan housing with the air direction arrows pointing upward and away from the frequency converter.

Slide the fan housing and fan under the retaining clips on top of the frequency converter.

Fasten 2 screws (T25) in the single fan housing, securing it to the frequency converter.

Place the front cover on the frequency converter, and fasten with 2 screws (T25).

2.7 Removing the Top Fan and Double Fan Housing

To remove the top fan and double fan housing, use the following steps. Refer to Illustration 3.

Unfasten 4 screws (T25) and remove the upper front cover of the frequency converter.

Installation

Top Fan Kit for FA09-FA12/D3h-D4h/E3h-E4h

Application Guide

Remove 2 screws (T25) from the fan housing.

Slide the fan housing and fans out from under the retaining clips.

Unplug the in-line connector attaching the fan cable.

Feed the cable through the cable access hole.

Lift the fans from the pins in the fan housing.

e30bf769.10

Illustration 3: Top Fan and Double Fan Housing

Double fan housing

Mounting pin (inside housing)

Fan

Screw (T25)

Cable access hole

Retaining clip

2.8 Installing the Top Fan and Double Fan Housing

To replace the top fan and double fan housing, use the following steps.

Place 2 fans over the pins in the double fan housing.

Check that the air direction arrows point upward and away from the frequency converter.

Feed the fan cables through the cable access hole in the top plate.

Attach the in-line cable connectors.

Slide the double fan housing and 2 fans into position under the retaining clips.

Secure 2 screws (T25) in the fan housing.

Replace the upper front cover on the frequency converter, and fasten with 4 screws (T25).

Installation

Top Fan Kit for FA09-FA12/D3h-D4h/E3h-E4h

Application Guide

Installation

Top Fan Kit for FA09-FA12/D3h-D4h/E3h-E4h

Application Guide

Danfoss A/S

Ulsnaes 1

DK-6300 Graasten

danfossdrives.com

Any information, including, but not limited to information on selection of product, its application or use, product design, weight, dimensions, capacity or any other tech-

nical data in product manuals, catalogues descriptions, advertisements, etc. and whether made available in writing, orally, electronically, online or via download, shall be

considered informative, and is only binding if and to the extent, explicit reference is made in a quotation or order confirmation. Danfoss cannot accept any responsibility

for possible errors in catalogues, brochures, videos and other material.

Danfoss reserves the right to alter its products without notice. This also applies to products ordered but not delivered provided that such alterations can be made without

changes to form, fit or function of the product.

*130R0767*

Installation

Top Fan Kit for FA09-FA12/D3h-D4h/E3h-E4h

Application Guide

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accionamiento de CC de Danfoss

Danfoss

Danfoss VLT AutomationDrive FC 300 Guía

Danfoss

Danfoss VLT AutomationDrive FC 361 Guía

Danfoss

Danfoss VLT DriveMotor FCP 106 Guía

Danfoss

Danfoss VLT Automation Drive FC 360 Instrucciones de funcionamiento

Danfoss

Danfoss VLT CDS 803 Manual de usuario

Danfoss

Danfoss VLT MSD 510 Manual de usuario

Danfoss

Danfoss VACON 100 industrial Manual de usuario

Danfoss

Danfoss VLT HVAC FC 100 Manual de usuario

Danfoss

Danfoss FC 300 Manual de usuario

Danfoss

Danfoss VLT HVAC Drive FC 102 Instrucciones de funcionamiento

Danfoss

Danfoss VLT HVAC Drive FC 102 Manual de usuario

Danfoss

Danfoss VLT Instrucciones de funcionamiento

Danfoss

Danfoss VLT HVAC Drive FC 100 Series Guía

Danfoss

Danfoss FC 300 Instrucciones de funcionamiento

Danfoss

Danfoss VLT AutomationDrive FC 360 Guía

Danfoss

Danfoss VLT Active Front End AFE 302 Manual de usuario

Danfoss

Danfoss VLT AQUA Drive FC 202 Manual de usuario

Danfoss

Danfoss VLT Midi Drive FC 280 Manual de usuario

Danfoss

Danfoss VLT HVAC Drive FC 102 Manual de usuario

Danfoss

Danfoss VLT Midi Drive FC 280 Guía

Danfoss

Danfoss VLT HVAC Drive FC 102 Manual de usuario

Danfoss

Danfoss ADAP-KOOL Drive Instrucciones de funcionamiento

Danfoss

Danfoss VLT Micro Drive FC 51 Series Manual de usuario

Danfoss

Danfoss VLT FC 103 Guía

Manuales populares de Accionamiento de CC de otras marcas

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manual de usuario

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manual de lista de piezas

Chamberlain Garog

Chamberlain Garog D Series Manual de usuario

Parker

Parker PDS Series Manual de usuario

Festo

Festo DGC G Series Guía de configuración

Binks

Binks QS-5012-1-CE Manual de usuario

ABB

ABB ACQ580-01 Series Manual de instalación

YASKAWA

YASKAWA CANopen SI-S3 Manual de usuario

GE D20A6 Manual de usuario

Unex

Unex MC-D-250-1000-050W-TW Manual de usuario

Geckodrive

Geckodrive G213V Manual de usuario

ABB

ABB RSYC-01 Manual de usuario

Rockwell Automation

Rockwell Automation PowerFlex 700S Manual del propietario

WEG

WEG DeviceNet CFW500 Manual de usuario

Siemens

Siemens SINAMICS G Hoja de datos

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Instrucciones de funcionamiento

SOMFY

SOMFY JR RU 30 Manual de usuario

Beckhoff

Beckhoff AX8911 Manual del operador