Dancing Wings DW DANCING PITTS Manual de usuario
DW DANCING PITTS INSTRUCTION MANUAL
1
DW DANCING PITTS INSTRUCTION MANUAL
EPP
DW DANCING PITTS
Biplane trainer airplane
Accessories include
QR
S
S1 S2
TU
O
P
M
N1
N
L
K
J
I
H
F
G
D
E
A
B
C
A.Up wing
B.Down wing
C.Fuselage
D.Fin
E.Rudder
F.Paper hinges
G.Cover for landing gear
H.ServPreparation Toolo
I.Servo horns
J.Wooden connecting pieces for wing top & bottom
K.Steel wire
L.Wooden pieces of landing gear
M.Glue
N.Wheel of nose landing gear
N1.Screw for nose landing gear
O.Wheel of back landing gear
P.Y wire
Q.20A speed controller
R.motor
S.Wooden pieces for motor mount
S1.Self-tapping screw for motor mount
S2.Fixed screw for motor
T.Propeller
U.Prop adapter
Preparation Tool
Specification
Wingspan: 850mm
Length: 680mm
Flying Weight≈700g
Suggested Equipment
Battery:3s 1500-2200mAh
Motor:2830 1050KV
Propeller:9-10inch
ESC: 20A
Servo:9g*4
Radio≥4CH
DW DANCING PITTS INSTRUCTION MANUAL
Body Installation Steps
m1 m2
m3 m4
w1 w2 w3
w5
w6
w7
w8
w9
w4L
w4R
w4L
w4R
w3
w9
w7
w2
w1
w6
w8
w5
Border line alignment
m4
m3
All parts
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Step 8
complete
2
DW DANCING PITTS INSTRUCTION MANUAL
3
0.01 Install the servo with short wire inside the
0.02 Install the rudder arm of servo, and let the
long servo to connect steel wire which need to
through out from the bilateral reserved hole.
The end of steel wire links the rudder arm. (Adjust
the servo arm come back to middle position during
installation.
0.03 Insert the rudder into the tail of fuselage,
with glue.
adjust it to keep level with the fuselage, and glue
it with fuselage. Plug the rudder and fuselage into
0.05 Contrast the position of steel wire, use a knife
to make cuts on the horizontal wing and vertical
the plastic clip of the servo horns into steel wire,
then link the plastic clip and servo horns.the paper
How to Assemble
DW DANCING PITTS INSTRUCTION MANUAL
4
0.06 Contrast the position of the back landing
gear’s screw holes, make the holes of tail wooden
pieces, install the back landing gear.
0.07 Use the S2 screws to install motor mount at
the bottom of motor.
it with prop adapter. Then connect the speed
controller and motor.
0.09 Put the speed controller part into the head of
it with S1 screw.
0.10 Install the long wire servo under the other
embed the servo’s outgoing line into the wing.
0.11 Let the servo line penetrate from the middle
hole of the wing, extend to front.
0.12 Make a cut to insert the servo horns on the
with glue.Insert the plastic clip on the short steel
wire, use the steel wire to connect the servo and
aileron’s servo horns, pay attention to the same
installation direction of left and right .
DW DANCING PITTS INSTRUCTION MANUAL
5
adjust it to keep level with the fuselage, and glue
it with fuselage. Plug the rudder and fuselage into
0.14 Plug the landing gear into the other side of
0.15 Apply the glue evenly over the joint of the
fuselage and wing, keep the down wing parallel
with fuselage, then glue together.
0.16 Insert the wooden connecting pieces for wing
top & bottom on the down wing, install the up
wing. Apply the glue on the other side of up wing’s
centre position, glue the up wing and fuselage.
0.17 Put the battery and receiver into the fuselage,
Tabla de contenidos
Otros manuales de Juguete de Dancing Wings
Dancing Wings
Dancing Wings OLD FOGEY Manual de usuario
Dancing Wings
Dancing Wings SCG42 Manual de usuario
Dancing Wings
Dancing Wings DW PTERODACTYL Manual de usuario
Dancing Wings
Dancing Wings DW MINI EAGLE Manual de usuario
Dancing Wings
Dancing Wings LIGHTING EPP Manual de usuario
Dancing Wings
Dancing Wings DW DANCING POKE Manual de usuario
