Dalsa Touch GEVA Series Manual de usuario
GV-312T
Touch Series GEVA Vision System
Installation Manual
405-00046-00
September 9, 2014
Revision 1.1
2
Notice
GV-312T Installation Manual
Document Number 405-00046-00
Revision: 1.1
Copyright 2014 Teledyne DALSAIncorporated.
All rights reserved.
All copyrights in this manual, and the hardware and software described in it, are the
exclusive property of Teledyne DALSAIncorporated and its licensors.
Claim of copyright does not imply waiver of Teledyne DALSAIncorporated or its
licensors other rights in the work. See the following Notice of Proprietary Rights.
NOTICE OF PROPRIETARY RIGHTS
This manual and the related hardware and software are confidential trade secrets
and the property of Teledyne DALSAIncorporated and its licensors. Use,
examination, reproduction, copying, transfer and/or disclosure to others of all or
any part of this manual and the related documentation are prohibited except with
the express written consent of Teledyne DALSA Incorporated.
The information in this document is subject to change without notice. Teledyne
DALSAIncorporated makes no representations or warranties with respect to the
contents of this manual and specifically disclaims any implied warranties of
merchantability or fitness for a particular purpose.Teledyne DALSAIncorporated
assumes no responsibility for errors or omissions in this document.
iNspect Express, Sherlock, and the Teledyne DALSAlogo are trademarks of
TeledyneDALSA Incorporated.All other trademarks are the property of their
respective owners.
Teledyne DALSA Industrial Products
Information: info.ipd@teledynedalsa.com
Support: support.ipd@teledynedalsa.com
Web: http://www.teledynedalsa.com/visionsystems
700 Technology Park Drive
Billerica, MA, USA 01821
Tel 1.978.670.2002 Fax 1.978.670.2010
3
Certifications
Declaration of Conformity
Supplier Teledyne DALSA Industrial Products Inc.
700 Technology Park Drive
Billerica MA 01821
USA
CE This product is in compliance with the directives of the
European Union. It has passed the CE test for environmental
specifications when shielded cables are used for external
wiring. A certificate of compliance is available upon request.
FCC This product has been tested and found to comply with the
limits for a class A digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio
frequency energy and may cause harmful interference to radio
communication.
4
Care should always be exercised when handling and operating this product. Even
though the system is encased within a rugged, industrial enclosure, incorrect use or
handling can result in damage to your investment. To prevent this, you should avoid the
following:
Handling Precautions
•Hot-plugging cables and devices. Be sure to shut the system down and remove
power before connecting or disconnecting anything to it.
•Free-standing operation. It is advisable to mount the system properly to prevent it
from falling accidentally. Mounting hardware is provided with the system.
•Do not place hard or sharp objects directly on or against the touch screen.Avoid
exposing the touch screen to direct sunlight for prolonged periods.
•Operating the system in an environment outside of it’s recommended operating
conditions.
•Avoid the damage that ESD can cause. Never expose the internal electronics to a
potentially hazardous environment by opening the enclosure. Doing so may cause
serious damage.
User Service Warning
With the exception of the externally accessible CFAST solid state drive, this product has
no field-replaceable component. Tampering with the unit will void the product warranty.
Warranty
Teledyne DALSA warrants the GV-312T against defects in materials and workmanship
for a period of Twelve (12) months from the date of delivery. Teledyne DALSA and its
representatives expressly disclaim any and all other warranties.
Your sole remedy shall be repair or replacement of this product and associated optional
components, provided that the defective product is returned within the warranty period.
TeledyneDALSA assumes no liability for any damages, lost profits, lost savings or
consequential damage resulting from the use, misuse of, or inability to use this product.
If you need to return the product, you must contact the Teledyne DALSArepresentative
who sold it to you. Do not return your product to Teledyne DALSAwithout prior
authorization.
5
Table Of Contents
Introduction GV 312T Introduction ……………………............................... 6
System Components ……………………............................... 6
Product Support ……………………............................... 7
Installation Installation ……………………............................... 8
Panel Mount ……………………............................... 10
VESA Mount ……………………............................... 12
GigE Cameras ……………………............................... 13
Typical Configuration
using the PL-USB ……………………............................... 14
Typical Configuration
not using the PL-USB ……………………............................... 15
Software Getting Started ……………………............................... 16
Directory Structure ……………………............................... 16
The License Manager ……………………............................... 17
iNspect Express Setup ……………………............................... 18
Camera Selector ……………………............................... 19
iDiscover ………………………………………….. 20
Sherlock Setup ……………………............................... 21
Sapera CamExpert ……………………............................... 22
Sapera Acquisition
Wizard ……………………............................... 23
Changing Camera
Order ……………………............................... 24
Enhanced Write Filter ……………………............................... 25
Specifications GV-312T Specifications ……………………............................... 26
Mechanical Drawings ………………………………………….. 27
Appendix A Touch Screen
Calibration ………………………………………….. 28
6
Introduction
GV 312T is a low cost vision system with an integrated touch panel interface for
configuring and monitoring automated camera inspections on the factory floor. The
product is equipped with hardware interfaces and application software to support the
following:
•Detection and maintenance of GigE cameras on the local network
•Setup and modification of inspection solutions without requiring an external PC
•Runtime monitoring of inspections (operator interface)
•Runtime tool parameter editing
•Offline solution debugging using built-in emulation
The GV 312T system utilizes a dual-core processor running the Windows 7 Embedded
operating system. As such, users have the option of developing their own custom
operator interface instead of using the pre-installed interfaces supplied with the product.
Camera Network
PLC (if required)
Typical GV 312T System Setup
I/O Connections
USB LAN1LAN2
PL-USB
GV 312T
Switch
7
GV 312 Vision Systems are shipped with the components listed below. Take a few
moments to verify that everything has arrived in good condition. If your product has
been visibly damaged during shipment or is missing parts, please contact your Teledyne
DALSArepresentative immediately.
GV 312T System Components
Component Description
GV312T-XX GV 312T. 12” touch panel vision system. Includes Win7-
32bit Embedded O/S, 32 GB CFAST SSD, front panel mount
hardware clips, iNspect Express software (-03), Sherlock
software (-04).
Standard components (ship with every GV 312T):
Component Description
A-VESA-T VESA mounting hardware
A-PWR-24 DIN mountable 24VDC power supply
A-CAM-XXXXXX-XX Genie GigE cameras
A-CAB-GE-X Ethernet cables
A-CAB-GEVA-FX GEVA I/O cables
A-PL-USB USB I/O breakout module
Optional components (Partial listing shown):
Product Support
This manual will assist you with the installation and setup of your GV 312Tproduct and
the embedded software. It describes what the product supports and how to connect the
external interfaces. If your questions are not answered in this reference, please contact
your local Teledyne DALSArepresentative.
8
Installation
Review user interface controls, connections and mounting holes
1 2
3
Front View
1. Reset button – front accessible USB port
2. 12” Touch LCD display (refer to appendix A for touch screen calibration)
3. Press control function keys as follows:
2
9
Installation
1 2
Bottom View
1. Power Input – 24 VDC.
2. Four RS-232 ports
3. DVI port for optional 2nd display
4. Two Gigabit Ethernet ports. Default IP settings are as follows (these can optionally
be changed through the Windows network “adapter change settings” interface):
Marking Default IP Connection
LAN1 Dynamic IPAddress DHCP enabled LAN network
LAN2 Static IPAddress 192.168.11.1 Camera Port 1
LAN left LED: Off = 10 Mbits/s; GREEN = 100 Mbits/s; ORANGE = 1000 Mbits/s
LAN right LED: ON = port active; BLINK = port traffic
Jumbo frames enabled on Camera Port, not enabled on LAN1 port.
NOTE: Genie Ethernet cables must be type Cat5 or Cat5e.
5. Four USB 2.0 ports
4 53
10
Installation
Mount the Unit (Panel Mount)
Locate the panel mounting clips included with the product. Put the clamps
into the holes located on the sides of the product as shown:
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Sistema de visión artificial de Dalsa
Manuales populares de Sistema de visión artificial de otras marcas
Festo
Festo SBOC-M-R1B-H Manual de usuario
Banner
Banner VE200G1B Manual de usuario
SVS-Vistek
SVS-Vistek CoaxPress EoSens Creation 1.1CXP2 Manual de usuario
Sony
Sony Vision Exchange PEQ-C100 Manual de usuario
Datalogic
Datalogic MX-U81 Instrucciones de instalación
Cognex
Cognex In-Sight D900 Series Manual de usuario
Spektrum
Spektrum SPMVR2520 Manual de usuario
Huaray
Huaray Movidius Series Manual de usuario
Daheng Imaging
Daheng Imaging MERCURY2 USB3 Manual de usuario
SVS-Vistek
SVS-Vistek exo174 U3 Series Manual de usuario
Teledyne
Teledyne e2v Eliixa+ Series Manual de usuario
Photron
Photron FASTCAM Mini CX Series Manual de usuario
