Daewoo DWF-600M Manual de usuario

Service Manual

Auto Washer

Model :

DWF-600M

DAEWOO ELECTRONICS CO., LTD.

1. SPECIFICATIONS

SPECIFICATIONS

NO. ITEM

1POWER SOURCE AVAILABLE IN ALL LOCAL AC VOLTAGE

POWER

50Hz 320W

CONSUMPTION

60Hz 300W(110~127V) / 340W(220V)

MACHINE NET

WEIGHT

GROSS

4 DIMENSION (WXHXD)

MATERIAL OF INTERNAL TUB

STAINLESS STEEL

WASHING PROGRAM

FULL AUTOMATIC 6 PROGRAMS

(FUZZY, FUZZY+SOAK, HEAVY, HEAVY+SOAK, SPEEDY, WOOL/SUIT)

WATER LEVEL SELECTOR

HIGH(55l), MID(45l), LOW(31l)

OPERATING WATER PRESSURE

0.3kgf/cm2~8kgf/cm2 (2.94 N/cm2~78.4N/cm2)

MAXIMUM MASS OF TEXTILE

6.0kg

REVOLUTION WASH 125~145(50Hz), 130~150(60Hz)

10 SPIN 710~725(50Hz), 760~785(60Hz)

PER MINUTE SUIT 50(50Hz), 60(60Hz)

WATER CONSUMPTION

APPROX. 130l/CYCLE

WATER LEVEL CONTROL

ELECTRONICAL SENSOR

13 ANTI NOISE PLATE OPTION

GEAR MECHANISM ASS’Y

SPUR GEAR

15 LINT FILTER O

16 SOFTENER INLET O

17 ALARM SIGNAL O

18 AUTO. WATER SUPPLY O

FUNCTION FOR BUBBLE

OPTION

AUTO RE-FEED WATER

21 AUTO POWER OFF O

DWF-600M

525X858X535

28.5kg/29kg(pump)

32kg/32.5kg(pump)

2. STRUCTURE OF THE WASHING MACHINE

STRUCTURE

•GROUND WIRE

In case of 3-wire

power cord, ground

wire will not be

provided

•POWER CORD

•DRAIN HOSE

•LINT FILTER

•COLD WATER TAP

After using the washer,

close the water tap

•DETERGENT CASE

•ADJUSTABLE LEG

•SOFTENER INLET

•BLEACH INLET

•CONTROL PANEL

•POWER SWITCH

•PULSATOR

•HOT WATER TAP

After using the washer, close the water tap.

In case of the single valve model,

there is no hot water valve.

DRYTEN(OPTION) HOSE ADAPTER UNDER COVER(OPTION)

INLET HOSE(OPTION)

HOSE CONNECTOR(OPTION)

CONNECTOR INLET(OPTION)

Accessories

The parts and features of your washer are illustrated on this page.

Become familiar with all parts and features before using your washer.

NOTE

• The drawing in this book may vary from your washer model. They are designed to show the different fea-

tures of all models covered by this book, Your model may not include all features.

• Page references are included next to same features.

Refer to those pages for more information about the features.

@@@@@@@@e?

@@h?

@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?

@@@@@@@@

?@@

?@@@@@@@@

?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@

@@g

@@@@@@@@

DRAIN HOSE

In case of screw shaped inlet hoses

water tap adapters will not be provided.

NON PUMP MODEL PUMP MODEL

3. FUNCTIONS OF THE CONTROL PANEL

CONTROL PANEL

• Press this switch to turn the power on or off.

• It can be used to choose water temperature to be supplied.

• As the button is pressed, water temperature will be repeated.

COLD →COLD+HOT →HOT

• In case of the single valve model, there is no wash temperature selector function.

• It can be used to adjust amount of water according to the size of the load to be washed.

• As the button is pressed, water level is selected by MID →HIGH →LOW

• It can be used to pre-engage time for wash.

• It is the button for the partial process or the combination of each process (wash, rinse,

spin) (See page 7)

• If you want to change wash time, rinse times, spin time, you must press this button after

selecting each process by the process button. Also, this button can be used to spin only.

(See page 7)

• It can be used to select the full-automatic program.

• As the button is pressed, program will be selected by following order :

FUZZY →FUZZY+SOAK →HEAVY →HEAVY+SOAK →SPEEDY →SUIT(WOOL)

• Operation and temporary stop is repeated as it is pressed.

• When you want to change program in operating;

press the “START/HOLD” button →Select the program that you want to change →press

the “START/HOLD” button again.

RES.

HOURS

CONTROL

PROGRAM

Control panel has micom sensor.

As the buttons are pressed, the lamps indicating the selection of your desired washing program will light up.

RES.

CONTROL

PROGRAM

4. WASHING PROCEDURE AND PROGRAM SELECTION

PROCEDURE

1. FUZZY PROGRAM (SENSOR);

• This selection is for general washing except extraordinary clothes.

• Artificial brain sensor selects properly the various kind of washing condition such as washing time, rinse times,

spin time and water level. Procedure to press the button;

3. SPEEDY PROGRAM;

• This selection is useful to reduce water consumption and washing time for less dirty clothes. Procedure to press

the button;

2. HEAVY PROGRAM;

• This selection is effective for blue-jean, climbing clothes, rucksack, sports wear etc..

• Procedure to press the button;

§§

Full Automatic Program

1Put in the clothes 2Press the power switch. 3Press the Start/Hold button, and

close the lid.

1Press the power switch. 2

Press the program selec-

tion button for “SPEEDY

”

FUZZY

HEAVY

SPEEDY

WOOL/SUIT

3Select the water level

proper to the wash

load.

HIGH

MID

LOW

4Press the Start/Hold

button and close the lid.

PROGRAM

1Press the power switch. 2

Press the program selec-

tion button for “HEAVY”

FUZZY

HEAVY

SPEEDY

WOOL/SUIT

3Select the water level

proper to the wash

load.

HIGH

MID

LOW

4Press the Start/Hold

button and close the lid.

PROGRAM

4. SUIT(WOOL) PROGRAM;

• This selection is effective for suit/wool clothes. (1.2kg’s limitation for 1-time wash)

• Do not put leather clothes, or chamios clothes into the washing tub for washing. It may cause shrinkage or defor-

mation to the clothes.

• Please use the neutral detergents only.

• The water temperature is fixed to “COLD”.

• The water level “LOW” is not selected. Procedure to press the button;

PROCEDURE

1Press the power switch. 2

Press the program selection

button for “WOOL

” or “SUIT”.

FUZZY

HEAVY

SPEEDY

WOOL/SUIT

3Select the water level

proper to the wash

load.

HIGH

MID

LOW

4Press the Start/Hold

button and close the lid.

PROGRAM

1Press the power switch. 2

Press the program selection

button for “SOAK”

SOAK

§§

FUZZY

WASH

§ §

HEAVY

RINSE

§§

SPEEDY

SPIN

§§

WOOL/SUIT

3Select the water level

proper to the wash

load.

HIGH

MID

LOW

4Press the Start/Hold

button and close the lid.

PROGRAM

5. SOAK PROGRAM;

• This selection is effective for heavily soiled clothes.

• If you want to soak, press the program button to adjust to “FUZZY + SOAK” or “HEAVY + SOAK”. Precedure to

press the button;

PROCEDURE

§§

Reserved Washing

§§

Partial Process & Combination

WASH TIME CONTROL

• As the control button is pressed, wash time will be repeated as following;

12 →15 →18 →0 →6 →9min.

• If you don’t want wash process, you must adjust wash time to 0 min..

RINSE TIMES CONTROL

• As the control button is pressed, rinse times will be repeated as following;

2 →3 →4 →0 →1 time(s)

• If you don’t want rinse process, you must adjust rinse times to 0 times.

SPIN TIME CONTROL

• As the control button is pressed, spin times will be repeated as following;

5 →7 →9 →0 →1 →3 min.

• If you don’t want spin process, you must adjust spin time to 0 min..

• Reservation can be made from 2 hours to 48 hours.

• To make reservation to complete washing in 8 hours.

• Now the reservation is made.

• If you want to check the selected program, press the “START/HOLD” button again.

RES.

adjust to "8""--" shall blink

Select the program.

Adjust to water level

and water temperature. HOURS

MIN

HOURS

MIN

§§

Convenient Operation For Spin Only

• If you want spin oly, it is convenient to operate the button as following;

CONTROL

5. DIRECTIONS FOR INSTALLATION AND USE

DIRECTIONS

The opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.

§§

Location Of Washer

Check location where washer will be installed. Make sure you have everything necessary for correct installation.

Proper installation is your responsibility.

• Do not place or store your washer below 0˚C(32˚F) to avoid any damage from freezing.

• Install the washer on the horizontal sold foor.

NOTES

If the washer is installed on an unsuitable floor, it could make consider-

able noise, vibrate and cause a malfunction.

If washer is not level, adjust the front leg(A) up or down for horizontal set-

ting.

• Earthed electrical outlet(B) is required with 20cm of bottom back of

washer cabinet.

• Hot and cold water faucets (C) must be within 1M of the upper back of

the washer cabinet and provide water pressure 0.3kgf/cm2-

8kgf/cm2(2.94N/cm2-78.4N/cm2).

§§

Drain System

Never forget to install drain hose before operating your washer.

The packing box is opened, there are a drain hose.

• Conect the drain hose to the drain outlet at the back side of the washer.

Non-Pump Model Pump Model

1In case that it goes over a door sill.

Don’t let the height of the drain

hose exceed 20cm from the bottom

of washer.

2In case of extending the drain hose.

Don’t let the total length exceed 3m. 3Be careful that the end of the drain

hose is not immersed in water.

Non-Pump Model

• Top of tub must be at

least 86cm (34inches)

high and no higher than

130cm from bottom of

washer (A)

• Needs a 3cm minimum diameter standpipe with minimum

carry away capacity of 30liters per minute.

• Top of tub must be at

least 86cm(34inches)

high and no higher than

130cm from bottom of

washer (B)

Pump Model

Laundry tub drain system Standpipe drain system

UP DOWN

Drain hose

Drain Outlet

Drain hose

20Cm

CONNECTION

FOR ORDINARY TAP

6Connect the inlet hose adapter

of the hose to the water inlet of

the washer by turning it clock-

wise to be fixed tightly.

• Please check the rubber packing

inside the inlet hose adapter of

the hose.

1Pull down the collar

of the inlet hose to

separate it from the

water tap adapter. 2Loosen the four

screws at the water

tap adapter, but don’t

loosen the screws until

they are separated from

the water tap adapter.

4Remove the tape,

and screw connector

B into connect A tightly. 5Connect the inlet

hose to the water tap

adapter by pulling down

the collar of the hose end.

3Connect the water tap

adapter to the water tap and

tighten the four screws evenly

while pushing up the adapter

so that the rubber packing

can stick to the water tap

tightly.

§§

How to Connect the Inlet Hose

Be careful not to mistake in supplying between the hot(maximum : 50˚C) and cold water.

In using only one water tap or in case of attached one water inlet valve, connect the inlet hose to the cold water inlet

valve.

Do not over tighten : this could cause damage to couplings.

FOR SCREW-SHAPED TAP 3Insert the inlet hose adapter

into the water inlet of washer

and turn it to be fixed.

• Assert the packing in the inlet

1Connect the inlet

hose to the water tap

by screwing the con-

nector D tightly.

Inlet Hose

Connector D Rubber

Packing

Connector C

TAPE

Connector B

Connector A

¡collar

2Connect the connec-

tor-inlet supplied if

necessary.

Connector

Inlet

Rubber

Packing

Connector D

Connector C

Hose

CONVENIENCE

§§

How To Clean The Filter

Remove the dirt

from the inlet filter

with a brush.

Pull the

power plug

out before

cleaning it.

Turn off the

water supply

to the washer

and separate

the inlet hose.

Pull the

inlet filter out.

CLEANING THE LINT FILTER

CLEANING THE WATER INLET FILTER

• Clean the filter when water leaks from the water inlet.

CLEANING THE DRAIN FILTER

• In case of “U” shaped drain hose, this filter’s equipped at the back side of washer.

• This drain filter is to screen the foreign stuffs such as threads, coins, pins, buttons etc ..

• If the drain filter is not cleaned at proper time (every 10 times of use), drain problem could be caused.

3Return the filter as it was, and

insert the filter frame into the

slot.

1Pull the Filter frame

upward. 2Turn the lint filter

inside out, wash the

lint off with water.

1Put down the

remained water in the

hose. And put a container

under the filter to collect

water.

2Turn the cap counter-

clockwise. 3Pull out the filter assembly off

the case of the main body.

6Turn the cap clockwise tightly.

4Clean the drain filter

removing the foreign

stuffs. 5

Put in the filter along the

guiding prominence of the

case. Please note the left

position of the filter adjusting

the groove to the guide rib.

FILTER CONTAINER

CAP

SLIT

CASE

FILTER

CAP

FILTER

CAP

FILTER CASE

GUIDE

RIB

SLIT

CAP

Filter Frame

Lint Filter

Tabla de contenidos

Otros manuales de Arandela de Daewoo

Daewoo

Daewoo DWD-G1081TC Manual de usuario

Daewoo

Daewoo DW-1010 Manual de usuario

Daewoo

Daewoo DWC-ED1432 Manual de usuario

Daewoo

Daewoo DW-503M Manual de usuario

Daewoo

Daewoo DWD-FD1411 Manual de usuario

Daewoo

Daewoo DW-3610 Manual de usuario

Daewoo

Daewoo WM710T1WU4RS Manual de usuario

Daewoo

Daewoo DWD-F101(1~3) Manual de usuario

Daewoo

Daewoo DWF-216SP Manual de usuario

Daewoo

Daewoo DWD-M12CK Manual de usuario

Daewoo

Daewoo DW-K500C Manual de usuario

Daewoo

Daewoo DWF-150LD Manual de usuario

Daewoo

Daewoo C-UD121DCEPB Manual de usuario

Daewoo

Daewoo DW-1050 Manual de usuario

Daewoo

Daewoo DWD-AD123'S Manual de usuario

Daewoo

Daewoo DWD-F1021 Manual de usuario

Daewoo

Daewoo mini Manual de usuario

Daewoo

Daewoo DWM30-999PG Manual de usuario

Daewoo

Daewoo DWD-NT1211 Manual de usuario

Daewoo

Daewoo DWF-800MP Manual de usuario

Daewoo

Daewoo DWM-800C Manual de usuario

Daewoo

Daewoo DWF-260NSTC Manual de usuario

Daewoo

Daewoo HURRICANE CAT 3 Manual de usuario

Daewoo

Daewoo DWD-MV SERIES Manual de usuario

Manuales populares de Arandela de otras marcas

Tricity Bendix

Tricity Bendix AW 1000 W Guía del producto

Panasonic

Panasonic NA-F60L5WRB Manual de usuario

GE WSLP1500 Manual

Electrolux

Electrolux EWF1284EDW Manual de usuario

Bosch

Bosch WAN2829BSN Manual de usuario

LG TV2516DV3B Manual de usuario

LG TH2517DSAV Manual de usuario

VESTEL

VESTEL CMH-XL 7510 TE Manual de usuario

AEG

AEG 74335 Manual de operación

Johnson

Johnson JWF721A Manual de usuario

Beko

Beko WTE7604XLW0 Manual de usuario

Danby

Danby DTT100A1WDB Instrucciones de montaje

Amica

Amica WA 14 Ex Manual de usuario

Bosch

Bosch WAS28461AU Manual de usuario

Miele

Miele PW 6080 Vario Manual de usuario

Finlux

Finlux FLX108CF220 Manual de usuario

Whirlpool

Whirlpool 3LBR5132AN0 Manual de usuario

Beko

Beko WKB 51231 PTMA Manual de usuario