Daewoo electricals SDA1210 Manual de usuario
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions
should always be followed. These instructions should be
saved for future reference:
• Read and familiarise yourself with all operating instructions
before using this Steam Station Iron.
• Before plugging your unit into the mains, visually check that
the unit is intact and has not suffered any transit damage.
• Check that the voltage indicated on the data plate corresponds
with that of the local network before connecting the appliance
to the mains power supply.
• Close supervision is required when using this appliance near
children.
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children unless they are
older than 8 and supervised.
• Keep the appliance and its cord out of reach of children less
than 8 years when it is energised or cooling down.
• DO NOT touch hot surfaces. The outer surfaces are liable to
get hot during use. Always use the handles and knobs.
• Do not immerse the appliance or its cord in water or any other
liquids.
• Do not leave the appliance unattended during use.
• Do not leave the appliance unattended whilst connected to the
mains supply.
• Always use this appliance on a solid, level, non-flammable
surface.
• Do not use this appliance outdoors.
• Do not use this Steam Station Iron with a programmer, timer,
separate remote-control system or any other device that
switches the appliance on automatically.
• It is imperative to unplug the power cord after the appliance has
been used, before it is cleaned and whilst being repaired.
• Repairs to electrical appliances should only be performed by a
qualified electrician. Improper repairs may place user at serious
risk.
• Do not operate this appliance with a damaged plug or cord,
after a malfunction or after being dropped or damaged in any
way.
• Regular, periodic checks should be carried out on the mains
cable to ensure no damage is evident. Should there be any
signs of damage the appliance should not be used.
• If the power cable is damaged, it should only be replaced by the
manufacturer or a suitable qualified after-sales-service in order
to avoid a hazard
• Do not allow the mains cable to hang over sharp edges or
come in contact with hot surfaces.
• Do not run the mains cable under carpets, rugs, etc.
• The Iron is not to be used if it has been dropped, if there are
visible signs of damage or it is leaking.
• The plug must be removed from the socket outlet before the
reservoir is filled with water.
• The filling aperture must not be opened during use.
• Allow the unit to cool before storage.
• Before cleaning, disconnect the appliance from the mains
supply and allow to cool.
• This appliance is intended for household use only and should
not be used for industrial purposes.
• Do not use any accessories or attachments with this appliance
other than those supplied or recommended by supplier.
• Do not use this appliance for anything other than its intended
use.
• Do not push objects into any openings as damage to the
appliance and/or electric shock may occur.
• Ensure appliance is situated in an open area, do not allow it to
come in contact with Cupboards, Curtains, wall coverings,
clothing or other flammable materials.
• Unplug after each use. Grasp the plug, not the cord.
NB: During the first few minutes of initial use, you may
notice a slight odour and a little smoke. This is normal and
will quickly disappear, It is the coating applied to the
heating elements to prevent any corrosion during transit.
!
Before leaving the factory this appliance is vigorously
tested and therefore there may be some residual water in
the water tank and/or hose.
Description of parts
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!
!
!
!
!
!
!
!
!
!
!
1. Detachable Water Tank
2. Iron Heating Indicator
3. Continuous Steam Button
4. Manual Steam Trigger
5. Temperature Control
6. Cord Storage Clip
7. Cable and Steam Monotube
8. Power Cable
9. Low Water Indicator
10.Steam Ready Indicator
11.Power Indicator Light
12.On/Off Switch
1
2
3
4
5
6
7
8
9
10
11
12
Before the first time you use your Steam Station Iron
!
Before using your Steam Iron for the first time remove the plastic protector from
the soleplate and clean the soleplate with a soft damp cloth.
!
Operating Instructions
To keep the base smooth do not run it over metal objects such as zips, buttons
etc.
Selecting the temperature
1. Refer to the ironing instructions on the garment to be ironed
2. If the garment doesn’t have any ironing instructions but you know the type of
fabric, use the guide on the temperature controller..
3. Fabrics with special finishes (polishing, pleats, etc) should be ironed at the
lowest temperature setting.
4. With mixed fibres always select the lowest applicable temperature.
5. Group items with similar fibres together, as the iron heats up faster than it cools,
start ironing items requiring the lowest temperature first.
6. Turn the temperature dial to the required setting according to the guide below:
Preparation For Use
1. Take out the water tank (1) and fill to the MAX level.
2. Replace the water tank ensuring that it is correctly position and fully closed.
3. Turn on the steam station by using the On/Off switch (12).
4. Set the temperature control (5) to the desired setting.
5. The Iron Heating Indicator (2) will illuminate until the iron has reached the
desired temperature.
6. When the steam temperature is reached the Steam Ready Indicator (10) will
illuminate.
Do not use chemically de-limed or perfumed water.
!
Steam Ironing
1. If using the steam function, set the Temperature Control (5) to the MAX setting.
2. When the Iron Heating Indicator (2) has gone out and the Steam Ready
Indicator (10) is illuminated, the Steam Station is ready to use.
3. For continuous steam press the Continuous Steam Button (3), this will
continuously release steam through the soleplate steam vents.
4. To stop the continuous steam function press the Manual Steam Trigger (4), this
will stop the continuous steam release and allow controlled steam release
using the Manual Steam Trigger (4).
5. When the Water Tank (1) is low on water the Low Water Indicator (9) will
illuminate.
a. Switch the Steam Station off at the On/Off Switch (12).
b. Press the Manual Steam Trigger (4) to fully exhaust the steam from the
tank.
c. Replace the iron onto it’s rest.
d. Disconnect from the mains power supply and refill the tank as described
above.
Care and Cleaning
Before carrying out any cleaning or maintenance of your steam station
ensure that it is switched off, disconnected from the mains supply and fully
cooled.
Normal tap water can be used in your steam station however in hard water areas
a build up of limescale can occur in the tank. To remove limescale deposits use a
75% water 25% vinegar solution.
Note: There is a filter in the bottom of the tank to reduce limescale build up in the
steam station.
!
!
To clean the body of the steam station use a soft damp cloth.
Do not use strong detergents or harsh abrasive cleaners to clean the steam
station
Electrical Connections
This appliance is fitted with a fused three-pin plug to BS 1363. If the plug has to
be removed, it should be cut off and carefully disposed of immediately. To avoid a
possible shock hazard, do not insert the discarded plug into a mains socket.
Fitting a new plug
The mains lead must be connected as shown below. The wires are coloured with
the following code - Brown wire = Live (L), Blue wire = Neutral (N), Green &
Yellow = Earth (E).
!
!
!
!
!
!
• The Blue wire must be connected to the terminal marked N or coloured Black.
• The Brown wire must be connected to the terminal marked L or coloured Red.
• The Green & Yellow wire must be connected to the terminal marked E or coloured
Green.
• Check that there are no cut or stray strands of wire inside the plug.
• Use a 13 Amp BS 1362 fuse, only use BSI or ASTA approved fuses.
• If you are in any way unsure which plug or fuse to use, always refer to a qualified
electrician.
• After replacing or changing a fuse on a moulded plug, the cover must be refitted
to the plug; the appliance must not be used without a fuse cover.
Connect
Brown to
Live (L)
Connect
Blue to
Neutral
(N)
Ensure the outer sheath of the
mains lead is securely held by the
cable clamp
Connect
Green &
Yellow to
Earth (E)
Technical Data
Voltage : 220-240V AC 50Hz
Rated power : 2000W
Model Number : SDA1210
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Tabla de contenidos
Otros manuales de Hierro de Daewoo electricals
