Da-Lite IDEA Screen Manual de usuario

INSTRUCTION BOOK FOR

IDEA™ Screen & Panoramic

for Nureva Span

Tools Required For Assembly

Phillips Screwdriver Level

Rubber Mallet Measuring Tape ⅜” Open Wrench

or Socket Driver

(IDEA Panoramic)

Disclaimer

Milestone and its ailiated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete.

However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide

for every possible contingency in connection with the installation or use of this subject to change without notice or obligation of any

kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone

assumes no responsibility for accuracy, completeness or suiciency of the information contained in this document.

Important Safety Instructions

1. Read and understand all instructions before using.

2. Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the

installer’s responsibility to make sure the structure to which this component is attached can support the weight of all equipment. Reinforce

the structure as required before installing the component.

3. Use this projection screen only for its intended use as described in these instructions. Do not use attachments not recommended by the

manufacturer.

Save These Instructions

1/4” Wrench

Hardware Provided - Touch Module Bracket

(2) #8 x ½” Screws(2) #4 x ½” Screws (2) #4 Nuts (1) Bracket

Hardware Provided - IDEA Panoramic (Multi-Panel)

#8 x ½” Screws

Number of supplied screws

varies by screen size

44” Wall Bracket

See Table 1 for Quantities.

28” Wall Bracket

See Table 1 for Quantities.

Seam Brace

See Table 1 for Quantities.

LBrackets

(4) - 2 Panel Screens

(6) - 3 Panel Screens

1032 Nuts

(4) - 2 Panel Screens

(8) - 3 Panel Screens

Hardware Provided - IDEA Screen (Single Panel)

(7) #8 x ½” Screws

(2) 44” Wall Brackets

(2) LBrackets

Wall Brackets and Seam Braces Included

Item Number Overall Dimensions Panels Wall Brackets Seam Braces

29512 46¾" x 122¾" 2(4) 28" 1

29513 46¾" x 245¾" 3(6) 28" 2

29636 50¾" x 89¾" 1(2) 44" -

29637 50¾" x 170¾" 2(4) 28" 1

29638 53¾" x 253¾" 3(6) 28” 2

Table 1

Preparation

It requires two people to assemble a single panel IDEA Screen and four people to assemble a multiple panel IDEA Panoramic. To

maintain optimal projected image geometry and screen alignment, a lat and straight wall free from obstructions and angular

distortions should be used.

Choose a clean work area for assembly using padded material or other soft, clean materials. The work area should be larger than the

overall screen size and directly in front of the location where the screen is to be installed. Carefully unpack unit and place assembly on top

of the clean work area.

Wall Mounting Instructions for Single Panel Screens

NOTE: The screen is shipped with two 44” wall brackets. Use

appropriate mounting hardware for the wall type and to

accommodate for the screen’s hanging weight (Figure 1).

1. Secure the two wall brackets to wall studs at the desired height.

The outside edge of each wall bracket must be no greater than

5” away from the left and right edges of the frame. You will need

at least 1” clearance above the drilled holes to hang the screen

(Figure 1) .

2. To install the (2) L-brackets, you must measure the overall height

of the screen frame and subtract 1⅛”. Using that dimension,

measure down from the top edge of the wall brackets and mark

the wall for two screw holes. The outside edge of each L-bracket

must be no greater than 5” away from the left and right edges of

the screen frame (Figure 1).

3. Secure the two L-brackets to the wall at the marked locations. The

longest side of the two L-brackets should be pointing upwards

when secured in order to hide the L-brackets behind the screen

frame once the screen is installed.

Wall Brackets

LBracket

No More

than 5”

No More

than 5”

No More

than 5”

Figure 1

Screws (Not Supplied)

Wall Mounting Instructions for Single Panel Screens (continued)

4. This step requires two people. Hang the screen on the wall

brackets. There is a lip on the back of the frame that wedges itself

into the wall brackets once fully installed. Ensure that the screen

clears the L-brackets and that the screen weight is on the wall

brackets, not the L-brackets.

#8 X ½" Screws

Figure 2

5. Tap the bottom of the two L-brackets with the rubber mallet until

they make contact with the frame. Secure the two L-brackets to

the frame with the remaining (4) #8 x ½” screws (Figure 2).

Assembly Instructions for Multi-Panel Screens

1. Carefully unpack unit and place all panels on top of the clean

work area. The viewing surface of each panel must face down.

2. Slide each panel together, aligning the both the top and bottom

frames (Figure 3).

3. Find (1) seam brace and remove the release liner from both strips

of adhesive tape.

4. Ensuring that the panels are still in alignment, line up the seam

brace with one of the panel seams with adhesive side facing

down. Do not press adhesive into panels yet. Maintain at least a

small gap between the adhesive and the panel.

Figure 3

Figure 4

5. Use ⅜” open wrench or socket driver and (4) 1032 nuts to attach

seam brace onto the studs on the top and bottom of screen

frame at the panel seam. Tighten all four nuts once attached to

the frame (Figure 4).

NOTE: For optimal seam alignment, hold the panels together

tightly while the seam brace is being adhered and the lock nuts

are being tightened.

6. Press adhesive into panels. Apply steady pressure along the

length of the seam brace to attach irmly.

7. For three panel screens, repeat Steps 36 to attach the second

seam brace.

1032 Nuts

Seam Braces

Wall Mounting for Multi-Panel Screens

NOTE: The screen is shipped with four or six wall brackets that

vary by screen size. Two brackets will be used on each of the

panels. Use appropriate mounting hardware for the wall type and

to accommodate for the screen’s total hanging weight.

1. Secure two panel wall brackets to wall studs at the desired height.

The outside edge of each wall bracket must be no greater than 5”

away from the left or right panel seams. You will need at least 1”

clearance above the drilled holes to hang the screen.

2. Secure the second two panel wall brackets to wall studs at the

height selected in Step 1. Each panel wall bracket should be

centered between the seam brace and left or right outside edge

of the frame when mounted to the wall (Figure 5). If you are

installing a two panel screen, proceed to step 4.

3. Secure the third two panel wall brackets to wall studs at the

height selected in Step 1. Each panel wall bracket should be

centered between the seam brace and left or right outside edge

of the frame when mounted to the wall (Figure 5).

NOTE: Do not proceed if all brackets are not level with each other

or a gap may appear between each of the panels when mounted.

4. To install the panel L-brackets, you must measure the overall

height of the screen frame and subtract 1 1/8”. Using that

dimension, measure down from the top edge of each of the wall

brackets and mark the wall for two screw holes. The outside edge

of each center panel L-bracket must be no greater than 5” away

from the panel seams (Figure 5).

5. Secure the two center panel L-brackets to the wall at the marked

locations. The longest side of the two center panel L-brackets

should be pointing upwards when secured in order to hide the

L-brackets behind the screen frame once the screen is installed

(Figure 5).

Figure 5

Wall Brackets

LBracket

No More

than 5”

No More

than 5”

No More

than 5”

Screws (Not Supplied)

Wall Mounting Instructions for Multi-Panel Screens (continued)

6. Repeat Steps 45 to install the remaining L-brackets for the

remaining panels.

NOTE: At this point, all L-brackets will be mounted on the wall; two

L-brackets for each panel. Do not proceed if all L brackets are not

level with each other on the wall.

Steps 78 require at least four people. Place one person on the

far left end of the screen, one person at the left panel seam,

one person at the right panel seam and one person on the far

right end of the screen. More people can be utilized as

needed. When lifting the screen of of the clean work area to

the wall and then onto the wall, it is crucial that the screen

remain coplanar and does not bend at the seams.

CAUTION: Any bend between the panels at the seams may

damage the screen or result in a permanent gap between the

seams.

7. Using all four people, carefully lift the fully assembled multi-panel

screen to an upright position and place underneath the mounted

wall and L-brackets. The screen will be parallel to the wall at the

end of this step.

8. Using all four people, carefully and in a smooth motion lift the

screen to hang it on the four installed wall brackets. There is a lip

on the back of the frame that wedges itself into the wall brackets

once full installed. Ensure that the screen clears all L-brackets and

that the screen weight is on the wall brackets, not the panel

L-brackets.

9. Tap the bottom of the panel L-brackets with the rubber mallet

until they make contact with the frame. Secure the panel

L-brackets to the frame with the remaining (12) #8 x 1/2” screws

(Figure 6).

Figure 6

#8 X ½" Screws

1. Using the provided #4 x ½” screws and #4 nuts, attach the

touch module base plate to the bracket.

2. Remove the cover from the touch module. Using the screws

provided with the projection system, attach the touch

module to the touch module base plate.

Figure 7

#8 x ½" Screws

#4 x 1/2” Screws

#4 Nuts

Screws Supplied with

Touch Module

Base Plate

Touch Module

Touch Module Bracket Installation

3. Position the bracket with the touch module along the top of

the IDEA frame according to your system’s installation

drawing. Using the two provided #8 x ½” screws, attach the

bracket and touch module to the IDEA frame with the touch

module facing towards the audience.

IMPORTANT: The vertical surface of the bracket should be

lush to the face of the IDEA frame.

4. Follow the instructions in the installation guide to set up

touch.

Otros manuales para IDEA Screen

Tabla de contenidos

Otros manuales de Pantalla de proyección de Da-Lite

Da-Lite

Da-Lite Tensioned Contour Electrol 38798LC Manual de usuario

Da-Lite

Da-Lite Model C Manual de usuario

Da-Lite

Da-Lite Advantage Manual With CSR Manual de usuario

Da-Lite

Da-Lite ADVANTAGE DELUXE ELECTROL Manual de usuario

Da-Lite

Da-Lite IDEA Thin Manual de usuario

Da-Lite

Da-Lite PERM WALL FRAME Manual de usuario

Da-Lite

Da-Lite 27971T Manual de usuario

Da-Lite

Da-Lite Horizon Electrol Manual de usuario

Da-Lite

Da-Lite Designer Contour Manual Manual de usuario

Da-Lite

Da-Lite TENSIONED PROFESSIONAL ELECTROL Manual de usuario

Da-Lite

Da-Lite Theater-lite Manual de usuario

Da-Lite

Da-Lite IDEA Panoramic Manual de usuario

Da-Lite

Da-Lite ADVANTAGE ELECTROL Manual de usuario

Da-Lite

Da-Lite Boardroom ElEctrol Manual de usuario

Da-Lite

Da-Lite EXECUTIVE ELECTROL Manual de usuario

Da-Lite

Da-Lite Tensioned Advantage Deluxe Electrol Series Manual de usuario

Da-Lite

Da-Lite Polacoat Da-Plex Semi-Rigid Manual de usuario

Da-Lite

Da-Lite Large Dual Masking Electrol Manual de usuario

Da-Lite

Da-Lite TENSIONED ADVANTAGE ELECTROL Manual de usuario

Da-Lite

Da-Lite Tensioned large advantage deluxe electrol Manual de usuario

Da-Lite

Da-Lite Designer Manual Manual de usuario

Da-Lite

Da-Lite ASCENDER ELECTROL Manual de usuario

Da-Lite

Da-Lite Deluxe Insta-theater Manual de usuario

Da-Lite

Da-Lite Perm Wall Frame Manual de usuario

Manuales populares de Pantalla de proyección de otras marcas

FART PRODUKT

FART PRODUKT Standard SCREEN Manual de usuario

Draper

Draper E Series Manual

Elite Screens

Elite Screens Elite Tripod Series Manual de usuario

Laarhoven

Laarhoven Companion II Manual de usuario

Renogy

Renogy RMS-LFPS-US Manual de usuario

Samsung

Samsung S*H65* Manual de usuario

FONESTAR

FONESTAR PPTR-43100-FA Manual de usuario

Slide Clear

Slide Clear Varro XL Manual de usuario

Elite Screens

Elite Screens M85XWS1-SRM Manual de usuario

OS РХ-090Н Manual de usuario

Niko

Niko 10-845 Manual de usuario

Speaka Professional

Speaka Professional 2357532 Manual de funcionamiento

Sima

Sima XL-72 Manual de usuario

Jasic

Jasic EVO 2.0 ET-200P Manual de usuario

Elite Screens

Elite Screens Starling 2 Series Manual de usuario

InFocus

InFocus SC-WALL GRY-92H Manual

Barco

Barco OverView MVL-615 Manual de usuario

Draper

Draper Envoy Manual