D-Link DCS-5220 Manual de usuario
Wireless G USB 2.0 Adapter
2D-Link DCS-5220 Quick Install Guide
System Requirements
• Windows®2000 or XP
• At least 128MB of memory (256MB recommended)
• A wireless (802.11b or 802.11g) or Ethernet network
• Internet Explorer 6.x or higher Internet Web Browser
• VGA card resolution: 800x600 or above
• CPU: 1.3GHz or above processor (2.4GHz processor or higher
with 512MB memory and a 32MB video card is required for
multiple camera viewing and recording in IP surveillance program)
Manual and Software on CD
Package Contents
D-Link DCS-5220
Wireless PT Internet Camera
with 3G Mobile Video Support
System Requirements
If any of the above items are missing, please contact your reseller.
Antenna CAT5 Ethernet Cable Power Adapter
3 D-Link DCS-5220 Quick Install Guide
Hardware Overview
Hardware Overview
Power LED
As soon as the power adapter is connected to the camera, the red LED and the
green LED light will both appear steady on. As the camera is booting, a ashing
red LED and steady green LED light will appear next.
The red LED will be turned off during self-test. Upon passing the self-test, a
steady red LED and ashing green LED light will appear, indicating a good
connection to the Ethernet port.
Antenna
One antenna is included with the DCS-5220. It is fastened onto the antenna
connector located on the back panel, which is used to provide a connection
with a wireless network.
Microphone
The DCS-5220 Internet
Camera has a built-in
internal microphone.
4D-Link DCS-5220 Quick Install Guide
Hardware Overview
Ethernet Cable Connector
The DCS-5220 features a RJ-45 connector for connections to 10Base-T
Ethernet cabling or 100Base-TX Fast Ethernet cabling. The port supports the
NWay protocol, allowing the DCS-5220 to automatically detect or negotiate the
transmission speed of the network.
Reset Button
When the reset button is pressed, the
power and activity LED light will both
appear steady on. While pressing the
reset button both LEDs will begin to
ash, indicating that the DCS-5220’s
settings are now restored to factory
default. Release the reset button.
DC Power Connector
The DC Power input connector is labeled
DC 12V with a single jack socket to supply
power to the DCS-5220.
5 D-Link DCS-5220 Quick Install Guide
Hardware Installation
Connect an Ethernet cable to the
Ethernet connector located on the
Internet Camera’s back panel and
attach it to the network.
Note: It is required that an Ethernet
cable is used during initial setup.
Once your wireless configuration is
set, you may disconnect the Ethernet
cable and begin communicating
wirelessly with your DCS-5220.
Attach the external power supply
to the DC power input connector
located on the Internet Camera’s
back panel (labeled DC 12V) and
connect it to an AC power outlet.
Hardware Installation
6D-Link DCS-5220 Quick Install Guide
Software Installation
Turn on the computer and Insert the D-Link DCS-5220 CD into
the CD-ROM drive. The following step-by-step instructions shown
here are demonstrations in Windows®XP, and are similar to other
Windows®operating systems.
If the CD Autorun function does not automatically start on your
computer, click Windows® Start > Run. In the Run command box
type “D:\DCS5220.exe”, where D: represents the drive letter of your
CD-ROM. If it does start, proceed to the next screen.
The InstallShieldWizard window
will appear.
Software Installation
Click Installation Wizard
Click Next
7 D-Link DCS-5220 Quick Install Guide
Software Installation
By default the program will be
installed to: C:\Program Files\
D-Link\Installation Wizard, where
C: represents the drive letter of
your hard drive.
To install to a different location,
click Browse and specify the
location.
Specify a Program Folder.
Setup is complete.
Click Next
Click Next
Click Finish
8D-Link DCS-5220 Quick Install Guide
Configuration
The D-Link DCS-5220 uses the Installation Wizard as the management
software. The wizard provides the user an easy interface to change
any settings related to the Wireless PT Internet Camera. Clicking on
the Installation Wizard icon will start the wizard.
The Installation Wizard will appear
and show the MAC address of the
DCS-5220 and an IP Address. If
you have a DHCP* server on your
network, there will be a valid IP
Address displayed here, indicated
by a “Yes” under the assigned
column.
*A DHCP server is a device that
supplies IP Addresses to its clients,
which are on the same network.
D-Link Installation Wizard
This section will show you how to congure your new D-Link Wireless
PT Internet Camera using the D-Link Installation Wizard.
Configuration
9 D-Link DCS-5220 Quick Install Guide
Configuration
If the Installation Wizard does not detect any devices, you will need
to reset the camera (see page 4 for instructions).
Click Search to refresh the list
of cameras.
10D-Link DCS-5220 Quick Install Guide
Configuration
Once the camera appears, select the camera by placing a check
mark in the box.
Enter an administrative password
in the Admin password and Conrm
password elds.
Note: For details on the Date and
Time Settings, please refer to the
Manual on the CD-ROM.
Click Next
Click Setup
Otros manuales para DCS-5220
3
Tabla de contenidos
Otros manuales de Cámara IP de D-Link
D-Link
D-Link SECURICAM Network DCS-3220G Manual de usuario
D-Link
D-Link DCS-4701E Manual de usuario
D-Link
D-Link DCS-1000 Manual de usuario
D-Link
D-Link DCS-1110 - Network Camera Manual de usuario
D-Link
D-Link DCS-5000L Manual de usuario
D-Link
D-Link SECURICAM Network DCS-2120 Manual de usuario
D-Link
D-Link DCS-2121 - SECURICAM Network Camera Manual de usuario
D-Link
D-Link SECURICAM Network DCS-900 Manual de usuario
D-Link
D-Link DCS-1000 Manual de usuario
D-Link
D-Link WIRELESS G DCS-950G Manual de usuario
D-Link
D-Link DCS-5030L Manual de usuario
D-Link
D-Link SECURICAM Network DCS-5300W Manual de usuario
D-Link
D-Link DCS-3715 Manual de usuario
D-Link
D-Link DCS-942L Manual de usuario
D-Link
D-Link SECURICAM Network DCS-950 Manual de usuario
D-Link
D-Link DCS-936L Manual de usuario
D-Link
D-Link DCS-942L Manual
D-Link
D-Link SECURICAM Network DCS-2100G Manual de usuario
D-Link
D-Link SECURICAM Network DCS-5300G Manual de usuario
D-Link
D-Link DCS-2330L Manual de usuario
