D-CUT Silverise Series Manual de usuario

SERIES

peration Manual

D-Cut TD-080 Wet Tile Saw

FOR YOUR SAFETY

This saw can be operated safely only when the operating instructions

have been completely read and strictly adhered to. It is

recommended to receive practical instruction before using the saw

for the first time.

Always inspect cable and plug before using the saw. The outlet

must be grounded. Have damage repaired only by a qualified

professional.

Do not use the saw in standing water or expose rain.

Wear hearing protection and safety goggles.

zAlways remove the plug from the power supply socket before removing saw

from work area, when interrupting work and when not using the saw.

zInsert the plug into the power socket only when the saw is switched off.

zAlways place the cable away from the saw towards the outside of the saw

table.

zDo not carry the saw by the cable.

zWear sturdy footwear.

zDo not use the saw when the blade is not installed properly.

zAlways switch off the saw before lifting the table for cleaning.

zOnly use original D-Cut accessories.

zNever leave the saw running unattended.

zKeep guards in place. Adhere to safety guidelines: (ANSI) American Safety

Standards Institute.

zNever stand or lean on equipment. Serious injury could occur if the machine

is tipped or is unintentionally contacted.

zDo not over reach. Keep footing and balance at all times.

zDisconnect tools. Before servicing, and when changing accessories such as

blades or profile tools. Turn off equipment!

zUse the correct tools. Do not force the equipment or accessory to do a job

for which it was not designed

zUse proper extension cord. Improper cord length and/or gauge is the

leading cause of premature electric motor failure! When in doubt use

heavier gauge cord.

zAn extra space needs to be remained around the machine as the working

table moves over the machine edge.

INNOVATION PUT TO WORK

Here at D Cut Products, Inc. We are always looking

to come out with new innovative products.

Check out Our Website for Updates at

www.dcutproducts.com

or contact us at

[email protected]

The serial number of your saw is

located on the left side above

the switch.

FOR YOUR (90 DAY) WARRANTY TO BE EFFECTIVE ON ALL

ELECTRICAL MOTOR AND PARTS SUCH AS THE SWITCH AND THE

CONTROL DEVICE, GAS ENGINE, AND PARTS, ALSO FOR YOUR

(1) ONE YEAR WARRANTY ON ALL OTHER PARTS, EXCLUDING

ABOVE COMPLETE THE WARRANTY CARD (PLEASE INCLUDE THE

SERIAL NUMBER) AND MAIL IT IN AS SOON AS POSSIBLE.

Fig.1

Warranty

card

Contents in the Box:

(1) Continuous rim

diamondblade,

(2) 45 degree

attachments, (1) wrench

set, (1) operation manual

and Warranty card.

Installation of the Blade

Open the “Open/Close

cover” and use provided

the wrench to install the

provided blade. Make

sure the cutting direction

shown on the blade is the

same direction of the

running motor.

Warning: The rotating

direction of the blade is

very important for cutting

correctly. Fig.2

Fig.3

Installation of the Guard

Use provided wrench to

install the blade guard

and the supporting bar

shown in Fig.3.

Warning: Do not remove

the middle screw as this is

to hold the motor housing.

Fill Water

Open the “Open/

cover” then pour water into

the tray. Water can be

added or refilled as

needed during saw

operation.

Supporting Bar

Extend out fully the

supporting bar before

moving the table. As

shown in Fig.6

Fig.4

Water Level Limit

The plug for the water tray

shown in Fig.5 is also a

water level control device.

Over filling the water will be

drained from the opening

at the top of the plug to

protect the motor.

Fig.5

Fig.6

Placing a Tile on the Table

Place a tile on the moving

table, flush against the

table back shown in Fig.8.

And then turn on the

motor.

Table Lock/Unlock Lever

Unlock the table as shown

in Fig.7 before moving the

table.

Fig.7

Fig.8

Cutting

After placing the tile on

the moving table, use

two hands to hold both

table back and the tile,

slowing push towards to

the running blade as

shown in Fig.9

Warning:

Never put hand(s) on the

notch port of the moving

table.

Fig.9

Attachment

Use the attachment shown

in Fig.10 as a limitation

stopper when repeatedly

cutting same size of the tile.

Warning:

Remove this attachment

from the table when not

needed.

Fig.10

0-90 Degree Attachment

Unlock the screw o

attachment shown in Fig.11

and set it to the proper

angle between 0-90

degrees, then lock the

degree setting screw.

Warning:

Remove this attachment

from the table when not

needed.

n the

Fig.11

5 Degree Attachment (2)

Set this attachment in right

position where 45 Degree is

assured, then lock the

attachment to the table

back shown in Fig.12.

Warning:

Remove this attachment

from the table when not

needed.

Fig.12

Drain the Water

Open the top cover right

above the water plug

shown in Fig.13 and pull the

plug.

Fig.13

Cleaning the Saw

Pour a bucket of clean

water from the “Open/

Close cover” throughout

the water tray and use the

provided scraper to clean

and remove the cutting

debris and slurry

Fig.14

Carrying

A conve

Handle

nient carrying

handle is located on the

side of the saw, opposite to

the switch, for

transportation purpose.

Fig.15

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sierra de D-CUT

D-CUT

D-CUT TA-070 Manual de usuario

Manuales populares de Sierra de otras marcas

RIDGID

RIDGID BS1400 Manual de usuario

ATIKA

ATIKA BWS 400-2 Manual de usuario

RGC

RGC FS20 Manual de usuario

Makita

Makita M2300 Manual de usuario

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manual de usuario

IMET Spa

IMET Spa SIRIO 370 AF-E Manual de usuario

Optimum

Optimum OPTisaw CS 275 Manual de usuario

Makita

Makita BPB180 Manual de usuario

Stihl

Stihl MS 462 C-M Manual de usuario

AEG

AEG TS 250 K Manual de usuario

Meec tools

Meec tools 004665 Manual de usuario

Makita

Makita LS1018L Manual de usuario

Ryobi

Ryobi RCS1400 Manual de usuario

DeWalt

DeWalt DCS391 Manual de usuario

Sealey

Sealey SA72 Manual de usuario

skilsaw

skilsaw SPT88 Instrucciones de montaje

Urrea

Urrea SI810 Dimensiones y guía de instalación

EINHELL

EINHELL BKG 210/1 Manual de usuario