Cyclops Lighting PAR-150CZ Manual de usuario

USER MANUAL

PAR-150CZ

150 Watt, Zoom, Cool White LED PAR

Caution!................................................................................................................. 3

Introduction........................................................................................................... 3

Safety instructions ............................................................................................... 3

Installation............................................................................................................. 3

Read ‘Safety information’ before installing the xture. ...................................................................4

Fastening the xture to a at surface................................................................................................4

Mounting the xture on a truss ..........................................................................................................4

Securing with a safety cable...............................................................................................................4

DMX-512 connection/connection between xtures..........................................................................4

Power connection................................................................................................................................5

Operation............................................................................................................... 5

Control Menu Map................................................................................................................................5

Addressing ...........................................................................................................................................6

Universal DMX Control........................................................................................................................6

RDM control..........................................................................................................................................6

Zoom function......................................................................................................................................7

DMX Protocol........................................................................................................ 7

ID address selection............................................................................................................................8

Fixture Cleaning ................................................................................................... 8

Fuse Replacement................................................................................................ 9

Troubleshooting ................................................................................................... 9

The xture does not work, no light ....................................................................................................9

Technical specications...................................................................................... 9

Table of contents

3Version 1.0

Caution!

Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric

shock when touching the wires!

Avoid looking directly into the light source!

Wear protective glasses and other PPE (personal protective equipment) when working on or near

the xture.

For your own safety, please read this user manual carefully before you initial start-up.

Follow operating safety precautions and pay attention to warning signs methods and equipment

on the user manual.

Indoor use only! To prevent risk of re or shock, do not expose this product to rain or moisture. IP

20 rating.

The ambient temperature must always be between -5° C and +45° C.

Always make sure you are connecting this product to the proper voltage in accordance with the

specications in this manual or on the product’s specication label.Make sure it is grounded when

using it!

Unplug mains lead before opening the housing!

Make sure that the power cord is never crimped or damaged by sharp edges. Check the xture

and the powercord from time to time.

Make sure to replace the fuse with another of the same type and rating.

Warning! This symbol indicates a hot surface. Certain parts of the housing can become hot

during operation. After use, wait for a cool-down period of at least 10 minutes before handling or

transporting the device.

Every person involved with the installation, operation and maintenance of this device has to

- be qualied

- follow the instructions of this manual

- consider this manual to be part of the total product

- keep this manual for the entire service life of the product

- pass this manual on to every further owner or user of the product

- download the latest version of the user manual from the Internet

Introduction

Thank you for having chosen PAR-150CZ. You will see you acquired a powerful and versatile device.

Unpack your item. Before you initial start-up, please make sure that there is no damage caused by

transportation. Should there be any, consult your dealer and do not use the device.

Safety instructions

This device has left our premises in absolutely perfect condition. In order to maintain this condition and

to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and

warning notes written in this user manual. Always disconnect from the mains, when the device is not in

use or before cleaning it. Keep away children and amateurs from the device! There are no serviceable

parts inside the device. Maintenance and service operations are only to be carried out by authorized

dealers.

4Version 1.0

Installation

Read ‘Safety information’ before installing the xture.

The xture is designed for indoor use only and must be used in a dry location with adequate ventilation.

Ensure that none of the xture’s ventilation slots are blocked.

Fasten the xture to a secure structure or surface. Do not stand it on a surface or leave it where it can

be moved or fall over. If you install the xture in a location where it may cause injury or damage if it falls,

secure it as directed in this user manual using a securely anchored safety cable that will hold the xture if

the primary fastening method fails.

Fastening the xture to a at surface

The xture can be fastened to a hard, xed, at surface that is oriented at any angle. Ensure that the

surface and all fasteners used can support at least 10 times the weight of all xtures and equipment to

be installed on it.

Fasten the xture securely. Do not stand it on a surface or leave it where it can be moved or fall over.

If you install the xture in a location where it may cause injury or damage if it falls, secure it as directed

below with a securely anchored safety cable that will hold the xture if the primary fastening method fails.

Mounting the xture on a truss

The xture can be clamped to a truss or similar rigging structure in any orientation. When installing the

xture hanging vertically down, you can use an open-type clamp such as a G-clamp. When installing in

any other orientation, you must use a half-coupler clamp that completely encircles the truss chord.

To clamp the xture to a truss:

1. Check that the rigging structure can support at least 10 times the weight of all xtures and equipment

to be installed on it.

2. Block access under the work area.

3. Fold the legs of the mounting bracket together and bolt a rigging clamp securely to the mounting

bracket. The bolt used must be M10, grade 8.8 steel minimum. It must pass through both mounting

bracket legs and be fastened with a self-locking nut.

4. Working from a stable platform, hang the fixture with its clamp on the truss and fasten the clamp

securely.

5. Secure the xture with a safety cable as directed below.

Securing with a safety cable

Secure the xture with a safety cable (or other secondary attachment) that is approved for the weight of

the xture so that the safety cable will hold the xture if a primary attachment fails.Loop the safety cable

through the eyebolt in the back of the xture and around a secure anchoring point. Do not loop the safety

cable around the xture’s mounting bracket only, as this will leave the xture unsecured if it separates

from the bracket.

DMX-512 connection/connection between xtures

Occupation of the XLR-connection:

5Version 1.0

1. Group

2. Signal (-)

3. Signal (+)

DMX OUT

1. Group

2. Signal (-)

3. Signal (+)

DMX IN

If you are using controllers with this occupation, you can connect the DMX-output of the controller directly

with the DMX-input of the rst xture in the DMX-chain. If you wish to connect DMX-controllers with other

XLR-outputs, you need to use adapter-cables.

Building a serial DMX-chain:

Connect the DMX-output of the rst xture in the DMX-chain with the DMX-input of the next xture.

Always connect one output with the input of the next xture until all xtures are connected.

DMX-512 connection with DMX terminator:

For installations where the DMX cable has to run a long distance or is in an electrically noisy

environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in

preventing corruption of the digital control signal by electrical noise. The DMX terminator is simply an

XLR plug with a 120 resistor connected between pins 2 and 3, which is then plugged into the output XLR

socket of the last xture in the chain.

Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120

resistor between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the

last xture.

Power connection

Power Requirements

The PAR-150CZ luminaire operates on 100 to 240 volts AC (+/- 10%, auto-ranging). The luminaire

contains an auto-ranging power supply.

Power linking between xtures:

The xture equiped with IP power in and out socket. Connect the power out to the power in socket in the

next xture till all are connected.

Caution: maximum power linking - 8 units.

Connection with the mains:

Connect the device to the mains with the enclosed power supply cable.

The occupation of the connection cables as below:

Cable color Connection International

Brown Live L

Blue Neutral N

Yellow/green Earth(Ground)

Operation

The PAR-150CZ can operate different modes. In each mode you can run the xture as a stand alone

fixture or in a master/slave confiugration. This next section will detail the differences in the operating

modes.

6Version 1.0

Control Menu Map

MENU SUB MENU OPERATION

Addr d001-d512 RDM/DMX address

CHnL

1CH

Channel mode

2CH

3CH

4CH

Strb S.00-s.20 Strobe with spead increasing

uL-- u.000-u.255 Dimmer

nodE

nod.0 Dimmer speed 0 (no delay)

nod.1 Dimmer speed 1

nod.2 Dimmer speed 2

nod.3 Dimmer speed 3

nod.4 Dimmer speed 4 (slowest speed)

Id Id.01-Id.66 ID address setting

tEnP -25~100 Fixture temperature

UErn Firmware version

rSEt yes/no Reset

pnnF (1.2~24.0)F PWM refresh rate adjustment(KHz)

Addressing

All xtures should be given a DMX starting address when using a DMX signal, so that the correct xture

responds to the correct control signals. This digital starting address is the channel number from which

the xture starts to listen to the digital control information sent out from the DMX controller. The allocation

of this starting address is achieved by setting the correct number on the display located on the base of

the device.

You can set the same starting address for all xtures or a group of xtures, or make different address for

each xture individually.

If you set the same address, all the units will start to listen to the same control signal from the same

channel number. In other words, changing the settings of one channel will affect all the fixtures

simultaneously.

If you set a different address, each unit will start to listen to the channel number you have set, based on

the quantity of control channels of the unit. That means changing the settings of one channel will affect

only the selected xture.

In the case of the PAR-150CZ, which is 1/2/3/4 channels xture. If you set, for example, the address in

the 2 channel mode to channel 3, the device will use the channel 3 to 4 for control.

Universal DMX Control

This function allows you to use a universal DMX-512 controller to control the dimmer and strobe. A DMX

controller allows you to create unique programs tailored to your individual needs.

RDM control

The PAR-150FZ can communicate using RDM (Remote Device Management) in accordance with ESTA’s

American National Standard E1.20-2006: Entertainment Technology RDM Remote Device Management

7Version 1.0

Over DMX512 Networks.

RDM is a bi-directional communications protocol for use in DMX512 control systems, it is the open

standard for DMX512 device conguration and status monitoring.

The RDM protocol allows data packets to be inserted into a DMX512 data stream without affecting

existing non-RDM equipment. It allows a console or dedicated RDM controller to send commands to and

receive messages from specic xtures.

With RDM function, you can set the DMX address of your fixtures remotely. This is especially useful

when the device is installed in a remote area.

Zoom function

This function allows you to adjust the beam width of the xture manually. Simply rotate the rotary knob in

the display panel to control the zoom(right stop = maximum spot, left stop = minimum spot).

DMX Protocol

1 Channel Mode Function Function Control

CH1 Dimmer 000-255: 0-100% dimmer

2 Channels Mode Function Function Control

CH1 Dimmer 000-255: 0-100% dimmer

CH2 Strobe 000-255: Strobe with speed increasing

3 Channels Mode Function Function Control

CH1 Dimmer 000-255: 0-100% dimmer

CH2 Strobe 000-255: Strobe with speed increasing

CH3 Dimmer mode

000-005: Menu setting

006-055: Dimmer speed 0 (no delay)

056-105: Dimmer speed 1

106-155: Dimmer speed 2

156-205: Dimmer speed 3

206-255: Dimmer speed 4 (slowest speed)

4 Channels Mode Function Function Control

CH1 Dimmer 000-255: 0-100% dimmer

CH2 Strobe 000-255: Strobe with speed increasing

8Version 1.0

4 Channels Mode Function Function Control

CH3 Dimmer mode

000-005: Menu setting

006-055: Dimmer speed 0 (no delay)

056-105: Dimmer speed 1

106-155: Dimmer speed 2

156-205: Dimmer speed 3

206-255: Dimmer speed 4 (slowest speed)

CH4 ID address setting

000-009: ID1-ID66

010-019: ID1

020-029: ID2

030-039: ID3

...

200-209: ID20

210: ID21

211: ID22

...

255: ID66

ID address selection

Each independent DMX address can have up to 66 ID addressed xtures. An ID address of 0 will activate

all ID address locations.

CH4 is used to select the target ID address.

DMX value Function DMX value Function DMX value Function

000-009 ID1-ID66 212 ID23 235 ID46

010-019 ID1 213 ID24 236 ID47

020-029 ID2 214 ID25 237 ID48

030-039 ID3 215 ID26 238 ID49

040-049 ID4 216 ID27 239 ID50

050-059 ID5 217 ID28 240 ID51

060-069 ID6 218 ID29 241 ID52

070-079 ID7 219 ID30 242 ID53

080-089 ID8 220 ID31 243 ID54

090-099 ID9 221 ID32 244 ID55

100-109 ID10 222 ID33 245 ID56

110-119 ID11 223 ID34 246 ID57

120-129 ID12 224 ID35 247 ID58

130-139 ID13 225 ID36 248 ID59

140-149 ID14 226 ID37 249 ID60

150-159 ID15 227 ID38 250 ID61

160-169 ID16 228 ID39 251 ID62

170-179 ID17 229 ID40 252 ID63

180-189 ID18 230 ID41 253 ID64

190-199 ID19 231 ID42 254 ID65

200-209 ID20 232 ID43 255 ID66

210 ID21 233 ID44

9Version 1.0

211 ID22 234 ID45

Fixture Cleaning

Due to fog residue, smoke, and dust cleaning the internal and external optical lenses and mirror should

be carried out periodically to optimize light output. Cleaning frequency depends on the environment

in which the fixture operates (I.e. smoke, fog residue, dust, dew). In heavy club use we recommend

cleaning on a monthly basis. Periodic cleaning will ensure longevity, and crisp output.

To clean the xture:

1. Disconnect the xture from power and allow it to cool for at least 10 minutes.

2. Vacuum or gently blow away dust and loose particles from the outside of the xture with low-pressure

compressed air.

3. Clean the surfaces by wiping gently with a soft, clean lint-free cloth moistened with a weak detergent

solution. Do not rub glass surfaces hard: lift particles off with a soft repeated press. Dry with a soft,

clean, lint-free cloth or low-pressure compressed air. Remove stuck particles with an unscented

tissue or cotton swab moistened with glass cleaner or distilled water.

4. Check that the xture is dry before reapplying power.

Fuse Replacement

This fuse is located in a fuseholder next to the MAINS OUT socket on the connections panel.

To replace a fuse:

1. Disconnect the xture from power and allow it to cool for at least 10 minutes.

2. Unscrew the cap of the fuseholder and remove the fuse. Replace with a fuse of the same size and

rating only.

3. Reinstall the fuseholder cap before reapplying power.

Troubleshooting

Listed below are a few common problems that you may encounter, with solutions.

The xture does not work, no light

• Check the connection of power and main fuse. Be sure the external fuse has not blown.

• Measure the mains voltage on the main connector.

10 Version 1.0

Input voltage: AC100-240V/50-60Hz

DMX connections 3 pin XLR In/Out male and female

Power connections: IP screw type power connection

Dimensions: 290 x 260 x 350mm

Net weight: 4 Kg

Color: Black

Housing: Aluminum

IP rating: 20

Operating temperature: -5°C/45°C

www.cyclopslighting.com

Model PAR-150CZ

Light source: 150 watts Cool White COB LED Equal to HPL 750 Par

Color temperature: 5600K

LED life expectancy: 50,000 Hrs.

CRI: 96; Ra≥94

TLCI: 96

Manual zoom RGBW

Zoom range: 25° to 80°

Light output: 12,000 Lux @ 2m @ 25°

5 Dimmer curves

Strobe

Video icker free with selectable PWM

Barn doors included

Control protocols: DMX, RDM

Control channels: 1, 2, 3, 4 CHs

Technical specications

Tabla de contenidos

Otros manuales de Equipo de DJ de Cyclops Lighting

Cyclops Lighting

Cyclops Lighting FR-150W Manual de usuario

Cyclops Lighting

Cyclops Lighting PR-40C Manual de usuario

Cyclops Lighting

Cyclops Lighting PAR-150FZ Manual de usuario

Cyclops Lighting

Cyclops Lighting PR-250T Manual de usuario

Cyclops Lighting

Cyclops Lighting PAR-100UV Manual de usuario

Cyclops Lighting

Cyclops Lighting PAR-150WZ Manual de usuario

Cyclops Lighting

Cyclops Lighting FR-50T Manual de usuario

Cyclops Lighting

Cyclops Lighting PR-300W Manual de usuario

Cyclops Lighting

Cyclops Lighting FR-40W Manual de usuario

Cyclops Lighting

Cyclops Lighting FR-150C Manual de usuario

Cyclops Lighting

Cyclops Lighting PR-300C Manual de usuario

Cyclops Lighting

Cyclops Lighting PR-350S Manual de usuario

Cyclops Lighting

Cyclops Lighting FR-300C Manual de usuario

Cyclops Lighting

Cyclops Lighting FR-40F Manual de usuario

Cyclops Lighting

Cyclops Lighting PAR-350W Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario