CyberPower PR750ELCDRT1U Manual de usuario

User’s Manual

Professional Rackmount Series

PR750ELCDRT1U

PR1000ELCDRT1U

EN ES FR IT GR

K01-0000763-00

This manual contains important instructions. Please read and follow all instructions carefully during installation and

operation of the unit. Read this manual thoroughly before attempting to unpack, install, or operate the UPS.

CAUTION! The UPS must be connected to a grounded AC power outlet with fuse or circuit breaker protection. DO NOT

plug the UPS into an outlet that is not grounded. If you need to power-drain this equipment, turn it off and unplug the

unit.

CAUTION! The battery can power hazardous components inside the unit, even when the AC input power is

disconnected.

CAUTION! The UPS should be near the connected equipment and easily accessible.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area, free

of conductive contaminants. (Please see specifications for acceptable temperature and humidity range).

CAUTION! To reduce the risk of an electric shock, do not remove the cover, except to service the battery. There are no

user serviceable parts inside, except for the battery.

CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source before servicing the

battery or installing a computer component.

CAUTION! To reduce the risk of fire, connect the UPS to a circuit with 10 Amps maximum over-current protection in

accordance to CE requirements.

CAUTION! The AC outlet where the UPS is connected should be close to the unit and easily accessible.

CAUTION! Please use only VDE-tested, CE-marked mains cable, (e.g. the mains cable of your equipment), to connect

the UPS to the AC outlet.

CAUTION! Please use only VDE-tested, CE-marked power cables to connect any equipment to the UPS.

CAUTION! When installing the equipment, ensure that the sum of the leakage current of the UPS and the connected

equipment does not exceed 3.5mA.

CAUTION! This is permanently connected equipment and only qualified maintenance personnel may carry out

installations.

CAUTION! Do not unplug the unit from AC Power during operation, as this will invalidate the protective ground

insulation.

CAUTION! DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! Under no circumstances this unit should

be used for medical applications involving life support equipment and/or patient care.

CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire, do not use with or near aquariums.

Condensation from the aquarium can come in contact with metal electrical contacts and cause the machine to short

circuit.

CAUTION! DO NOT USE WITH LASER PRINTERS! The power demands of laser printers are too large for this unit.

CAUTION! DO NOT INSTALL THE UPS WHERE IT WOULD BE EXPOSED TO DIRECT SUNLIGHT OR NEAR A

STRONG HEAT SOURCE!

CAUTION! DO NOT BLOCK OFF VENTILATION OPENINGS AROUND THE HOUSING!

CAUTION! DO NOT CONNECT DOMESTIC APPLIANCES SUCH AS HAIR DRYERS TO UPS OUTPUT SOCKETS.

IMPORTANT SAFETY INSTRUCTIONS

UNPACKING

The box should contain the following:

(1) UPS unit x 1; (2) User manual x 1; (3) Phone line x 1; (4) USB A+B type cable x 1; (5) Rack mount Brackets x 2; (6)

Emergency Power-Off Cable (gray) x 1; (7) Serial Interface Cable (DB-9) x 1; (8) Power Cord x 2

AUTOMATIC VOLTAGE REGULATOR (AVR)

The PR750ELCDRT1U/ PR1000ELCDRT1U can stabilize utility power inconsistences. The utility power may be

damaging to important data and hardware, but Automatic Voltage Regulation helps the computer not experience

dangerous voltage levels. The Automatic Voltage Regulator regulates low or high voltages to keep equipment working

at safe AC power levels, (220/230/240V), without switching to battery mode. Your equipment can operate normally

even during power problems, such as, shout brownouts and blackouts. The unit’s powerful sealed lead-acid batteries

will provide power only if the incoming voltage drops below 150V or increases above 300V.

SYSTEM BLOCK DIAGRAM

HARDWARE INSTALLATION GUIDE

1. Battery charge loss may occur during shipping and storage. For the first time the UPS is used, it is strongly

recommended to charge batteries for at least four hours in order to ensure maximum capacity. To do so, simply

plug the unit into an AC outlet.

2. When you use the included software, connect either the serial or the USB cable between the computer and the

corresponding port on the UPS. Note: If the USB port is used, the serial port will be disabled. They cannot be used

simultaneously. The computer with the PowerPanel® Business Edition S/W connects to the USB port or to the

serial port on the UPS. It can control the operating schedule, battery test, outlet, etc. and get information on the

UPS status. However, other computers with PowerPanel® Business Edition S/W can only get UPS status

information via a LAN connection.

3. With the UPS unit off and unplugged, connect your computer, monitor, and any externally powered data storage

device, (Hard drive, Tape drive, etc.) onto the outlets. DO NOT plug a laser printer, copier, space heater, vacuum

cleaner, paper shredder or other large electrical device into the UPS. The power demands of these devices will

overload and possibly damage the unit.

4. To protect a fax, telephone, modem line or network cable, connect the telephone or network cable from the wall

jack outlet to the jack marked “IN” on the UPS. Then, connect a telephone or network cable from the jack marked

“OUT” on the UPS to the modem, computer, telephone, fax machine, or network device.

5. Press the power switch to turn the UPS on. The Power-On indicator light will illuminate. If an overload is detected,

an audible alarm will sound and the UPS will emit one long beep. In order to reset it, turn the unit off and unplug

some equipment from outlets. Make sure your equipment carry a load current within the unit’s safety range, (refer

to the technical specifications), and then turn the unit on.

6. Your UPS is equipped with an auto-charge feature. When the UPS is plugged into an AC outlet, the battery will be

automatically charging, even when the unit is switched off!

INSTALLING YOUR UPS SYSTEM

7. To always maintain an optimal battery charge, leave the UPS plugged into an AC outlet at all times.

8. Before storing the UPS for an extended period of time, turn the unit OFF. Then cover it and store it with the

batteries fully charged. Recharge the batteries every three months or so, to ensure good battery capacity and long

battery life; further, this might also prevent damage to the unit from an unlikely battery leakage.

9. The unit provides one serial port and one USB port to allow connection and communications between the UPS and

any attached computer. The primary computer, (the one with PowerPanel® Business Edition S/W installed), is the

computer that you will use to control the UPS and make any changes to its operation. When there is a power failure,

the connected to the USB or Serial Port computer may be “asked” by the UPS for a graceful shutdown following a

possible pre-programmed time period delay indicated within the controlled S/W.

10. EPO (Emergency Power Off) Port: Use the provided gray cable to connect to a special EPO contact switch. Follow

the appropriate circuit diagram below to wire the cable to your EPO configuration. The EPO remote switch is a

switch installed in an outside area, connected to the unit via an ordinary RJ-11 phone line. In case of an emergency,

it can be used to immediately cut-off power from the UPS unit.

INSTALLING YOUR UPS SYSTEM (continued)

1. Multifunction LCD Readout: An LCD that shows various UPS information using icons and messages.

2. Power On Indicator: Indicates that the AC utility input power’s condition is normal and that the UPS outlets are

providing power, free of surges and spikes.

3. Power Switch: Master on/off switch for equipment connected to the UPS.

4. LCD Readout Toggle Button: Used to select among a variety of information the LCD can display.

5. Battery Backup and Surge Protected Outlets: The unit provides a total of six outlets with battery backup and surge

protection. They ensure that connected equipment will keep an uninterrupted operation over a period of time,

during a power failure.

Critical /Non-critical: It is possible to program the unit in a way so that the outlet block marked as “non-Critical”, (4

ports), will stop the provision of power to connected equipment after a certain period of time, thus making more

runtime available for the equipment connected on the outlets marked as “Critical”, (2 ports). In other words, the

user can establish runtime priority for certain connected equipment, maximizing its “availability” during a prolonged

power outage. This type of control takes place with the use of the provided PowerPanel® Business Edition S/W.

6. AC Inlet: Connect the AC Power cord to a properly wired and grounded outlet.

7. Input Circuit Breaker: This circuit breaker serves to provide input overload and fault protection.

8. USB port to PC: This is a connectivity port allowing communication and control among the UPS and the connected

computer. You should install on your computer the PowerPanel® Business Edition software appropriate to the

operating system you are using.

9. Serial Port: This is a connectivity port allowing communication and control among the UPS and the connected

computer. You should install on your computer the PowerPanel® Business Edition software appropriate to the

operating system you are using.

10. SNMP/HTTP Network slot: Remove the cover panel to install an optional SNMP, allowing your UPS be controlled

and monitored via a network connection.

11. EPO (Emergency Power Off) port: Allow for an emergency UPS Power-Off from a remote location.

12. Ground Stud: Use the Ground Stud to ground the UPS.

BASIC OPERATION

Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the batteries:

Servicing the batteries should only be performed by professionals. For further information please contact your dealer.

Make a note for the replacement battery pack number, (RBP0027), regarding PR750ELCDRT1U and

PR1000ELCDRT1U models.

CAUTION! Use only the specified type of battery: HR9-6(BB) for PR750ELCDRT1U/ PR1000ELCDRT1U. Contact

your dealer for replacement batteries.

CAUTION! The battery may represent the risk of electrical shock. Do not dispose of batteries on fire, since they may

explode. Follow all local ordinances regarding the proper disposal of batteries.

CAUTION! Do not open or mutilate the batteries. Released electrolyte is harmful to the skin and eyes and may be toxic.

CAUTION! A battery can present a high risk for short-circuits and electrical shocks.

Take the following precautions before replacing the battery:

1. Remove all watches, rings or other metal objects from your hands.

2. Only use tools with insulated handles.

3. DO NOT lay tools or other metal parts on top of the battery or any battery terminals.

4. Wear rubber gloves and shoes.

5. Determine if the battery is grounded. If so, remove ground source. CAUTION: CONTACT WITH A GROUNDED

BATTERY CAN RESULT IN ELECTRICAL SHOCK! The likelihood of such a shock will be greatly reduced if such

grounding is removed during installation and maintenance.

BATTERY REPLACMENT PROCEDURE

Remove the front panel on the right

side.

Remove the two retaining screws of

the cable protection cover, and then

remove the cover itself.

Disconnect the black and red wires

from the battery.

Remove the retaining screw.

Put the new battery packs back into the compartment.

Tighten up the screws and replace the cable protection

cover and the front panel. Recharge the unit for at least 8

hours to ensure that the UPS performs to the expected

runtimes.

REMINDER! The used batteries are hazardous wastes and must be disposed through recycling. Most retailers that sell

lead-acid batteries collect used batteries for recycling, as required by the local regulations.

BATTERY REPLACEMENT

1. Input voltage meter: This meter measures the AC voltage from the wall outlet. The INPUT voltage readout is used

to identify the input voltage information. When the UPS connects to any equipment, the AVR can provide a stable

220/230/240V power output. In the event of a complete loss of power, severe brownout, or over voltage, the UPS

relies on its internal battery to back up to supply a consistent 220/230/240V output.

2. Output voltage meter: This meter measures the output voltage from the UPS.

3. Estimated Run Time: This displays the estimated UPS runtime based on current load. When runtime becomes

shorted, the battery capacity will decrease; (battery capacity bar indicator will be falling).

4. Normal mode icon: This icon illuminates when the UPS is working under normal conditions.

5. Battery icon: When there is a severe brownout or blackout, this icon will appear followed by an alarm, (two short

beeps), indicating that the UPS is now working using its internal batteries. Once the batteries are run out of power,

(over a period of time), a constant alarm will sound. If this happens and main power has not been restored, it is

recommended that you save your files and turn off your equipment manually as soon as possible.

6. Silent mode icon: This icon appearing indicates that the buzzer will not be beeping while in battery operating

mode. During Silent mode, the unit’s alarm does not sound until the Battery Capacity falls to < 35%.

7. Over load icon: This icon will appear followed by an alarm, indicating that an overload condition has been reached.

To recover from the overload condition, start unplugging your equipment from the UPS outlets until the icon

disappears and the alarm stops.

8. LOAD CAPACITY: Load CAPACITY is shown as a bar chart; each segment indicates approximately a 25% of load

capacity.

9. BATT. CAPACITY: BATT. CAPACITY is shown as a bar chart; each segment indicates approximately a 25% of

battery capacity.

DEFINITIONS FOR ILLUMINATED LCD INDICATORS

General Mode

a. Press the “Display-Toggle” button to check the UPS status:

Items

Unit

Input Voltage

Output Voltage

Load Capacity

Battery Capacity

Estimated Runtime

Min

b. Press and hold the Display-toggle button for 4 seconds:

If the machine is in the Battery Mode with active alarm, it will become silent.

If the machine is in the Line Mode, a self- diagnostic test will take place.

c. If the Display-toggle button remains untouched for over 30 seconds, the LCD backlight will turn off automatically.

Set-up Mode

Step 1: Hold the Display-toggle button for 10 seconds to enter the UPS Set-Up Mode.

Step 2: By pressing the Display toggle, users can switch between setup functions. Some User Configurable functions

are as follows:

a. Sensitivity: Set the level of tolerance for UPS. Increase the UPS compatibility for local utility power condition.

-High: The UPS will turn to battery power more often to provide the steady power supply to the connected

equipment.

-Low: The UPS will tolerate more fluctuations and turn to battery power less often.

b. Voltage Mode: The AC output voltage on battery mode. There are 3 different settings (220,230,240).

These programmable items are sorted by unit as in the following table:

Items

Unit

Sensitivity

Voltage Mode (220/230/240)

Firmware Version

Step 3: Press and hold the display-toggle button for 4 seconds. When the icons blink, the value of each item can be

changed by slightly pressing the toggle.

Step 4: To save the value and return to general mode, press and hold the toggle for 4 seconds.

Note! If the machine is left idle for over 30 seconds during setup, it will turn off the backlight and return to general mode

automatically.

Note! If user wants to return to the general mode without saving changes, there are two methods:

(1) Wait for the backlight display to turn off, or,

(2) By pressing and holding the “Display-toggle key for 10 seconds.

LCD SETUP FUCTIONS

GreenPower UPS™

CyberPower's GreenPower UPSTM Circuit Design is a solution to this "Power Loss." When the

Utility Power is operating normally, GreenPower UPSTM works in a Bypass Mode. Our GreenPower

UPSTM design conducts power only through the Relay and still provides normal output voltage.

Bypassing the transformer reduces power consumption thereby conserving energy and saving

money. When the utility power is abnormal the UPS will operate under Battery or AVR Mode. Under

this condition GreenPower UPSTM and a traditional UPS would operate about the same. On

average utility power operates 88% of the time and the CyberPower GreenPower Technology will

work in its money/energy saving Bypass Mode.

Model

PR750ELCDRT1U

PR1000ELCDRT1U

Capacity (VA)

750

1000

Capacity (W)

600

800

Input

Nominal Input Voltage

220Vac – 240Vac

Input Voltage Range

160Vac – 290Vac

Input Frequency Range

50/60 Hz +/- 3 Hz (auto sensing)

Output

On Battery Output Voltage

Pure Sine Wave at 220/230/240Vac +/- 5%

On Battery Output Frequency

50/60 Hz +/- 1%

Transfer Time (Typical)

4 ms

Overload Protection

On Utility: Circuit Breaker, On Battery: Internal Current Limiting

Surge Protection and Filtering

Lightning / Surge Protection

Yes

Physical

Output Receptacles

(6) IEC 320 C13

Dimensions (cm)

1U Rack, 43.3 x 4.4 x49.0

Weight (kg)

17.6

Battery

Sealed Maintenance Free Lead

Acid Battery

6V / 9.0AH x 4

Hot Swappable External Battery

Yes

Warning Diagnostics

Indicators

Power On, LCD Display (Using Battery, AVR, Load Level, Battery Level)

Audible Alarms

On Battery, Low Battery, Overload

Environmental

Operating Temperature

32°F to 104°F (0°C to 40°C)

Operating Relative Humidity

0 to 95% Non-Condensing

Communication

PowerPanel® Business Software

Windows 10 / 8 / 7 / Vista / XP / 2000, Server 2008 / 2003

Management

Self-Test

Manual Self-Test

Auto-Charger/ Auto-Restart

Yes

COM/ Built-in USB Interface

Yes

SNMP/ HTTP Network Slot

Optional

CYBERPOWER GREENPOWER UPS™ TECHNOLOGY

TECHNICAL SPECIFICATIONS

Problem

Possible Cause

Solution

Outlet does not provide

power to equipment.

Circuit breaker has tripped due

to an overload.

Turn the UPS off and unplug at least one piece of

equipment. Wait 10 seconds, reset the circuit breaker

by depressing the button, and then turn the UPS on.

Batteries are discharged.

Recharge the unit for at least 4 hours.

Unit has been damaged by a

surge or spike.

Contact CyberPower Systems at

www.cyberpower.com.

Non-critical outlets have turned

off automatically due to an

overload.

Push the toggle button to make the uncritical outlets

turn on.

The UPS does not

perform expected

runtime.

Batteries are not fully charged.

Recharge the battery by leaving the UPS plugged in.

Batteries are degraded.

Contact CyberPower Systems about replacement

batteries at www.cyberpower.com.

The UPS will not turn

on.

The on/off switch is designed to

prevent damage by rapidly

turning it off and on.

Turn the UPS off. Wait 10 seconds and then turn the

UPS on.

The unit is not connected to an

AC outlet.

The unit must be connected to a 220/230/240v outlet.

The battery is worn out.

Contact CyberPower Systems about replacement

batteries at www.cyberpower.com.

Mechanical problem.

Contact CyberPower Systems at

www.cyberpower.com.

PowerPanel®

Business

Edition is inactive.

The serial cable or USB cable is

not connected.

Connect the cable to the UPS unit. You must use the

cable that came with the unit.

The cable is connected to the

wrong port.

Try another port on your computer.

The unit is not providing battery

power.

Shutdown your computer and turn the UPS off. Wait

10 seconds and turn the UPS back on. This should

reset the unit.

The serial cable is not the cable

that was provided with the unit.

You must use the cable included with the unit for the

Software.

For more information, contact us at:

Cyber Power Systems, Inc.

www.cyberpower.com

reserved. Reproduction in whole or in part without permission is prohibited.

PowerPanel® and PowerPanel® Plus are trademarks of Cyber Power

Systems (USA), Inc.

TROUBLESHOOTING

Otros manuales para PR750ELCDRT1U

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Unión Postal Universal de CyberPower

CyberPower

CyberPower OL6000RT3U Manual de usuario

CyberPower

CyberPower BR700ELCD Manual de usuario

CyberPower

CyberPower CyberShield CSN30U12V Manual de usuario

CyberPower

CyberPower EC450G Manual de usuario

CyberPower

CyberPower EC450G Manual de usuario

CyberPower

CyberPower SL700U Manual de usuario

CyberPower

CyberPower PR750ELCD Manual de usuario

CyberPower

CyberPower CP1350PFCLCD Manual de usuario

CyberPower

CyberPower Smart App Sinewave Series Manual de usuario

CyberPower

CyberPower Professional Tower UPS PP1500E Manual de usuario

CyberPower

CyberPower STANDBY UPS Series Manual de usuario

CyberPower

CyberPower OL1000XL Manual de usuario

CyberPower

CyberPower OR1000LCDRM1Ua Manual de usuario

CyberPower

CyberPower 649532010066 Manual de usuario

CyberPower

CyberPower AVR Series Manual de usuario

CyberPower

CyberPower 649532015597 Manual de usuario

CyberPower

CyberPower 649532215003 Manual de usuario

CyberPower

CyberPower Pro VP1000ELCD Manual de usuario

CyberPower

CyberPower 6K On-Line series Manual de usuario

CyberPower

CyberPower BU600E-AS Manual de usuario

CyberPower

CyberPower OR1500LCDRTXL2U Manual de usuario

CyberPower

CyberPower PR3000 Manual de usuario

CyberPower

CyberPower PR750LCDN Manual de usuario

CyberPower

CyberPower OR700LCDRM1U Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario

ZincFive

ZincFive BC Series Manual de usuario

BPC

BPC 1.5K SMART Manual de usuario

IBM

IBM 5595-1AX Manual de usuario