CyberPower PR1500 Manual de usuario

User’s Manual

Professional Rack Mount UPS

PR1500 / PR2200

ADDITIONAL INSTALLATION TIPS CAN BE FOUND AT:

www.cyberpowersystems.com/support.htm

TABLE OF CONTENTS

IMPORTANT SAFETY WARNINGS…………….……………………………………….………1

INSTALLING YOUR UPS SYSTEM…………………….………………………………………2

-UNPACKING…… ……………………………………………………………….2

- HARDWARE INSTALLATION GUIDE…………………………………………2

BASIC OPERATION……………………………………….....................................................3

- FRONT PANEL DESCRIPTION..................................................................3

- REAR PANEL DESCRIPTION…………………………………………...…….4

BATTERY REPLACEMENT AND STORAGE………………………………………….……..6

- BATTERY REPLACEMENT PROCEDURE……………....................…..….6

DEFINITION FOR ILLUMINATED LED INDICATORS………………………………….……8

TROUBLESHOOTING…………………………………………..………………….……………9

TECHNICAL SPECIFICATIONS………………………………………………….………..…..10

LIMITED WARRANTY AND POWER CONTROL GUARANTEE…………………….........11

Thank you for purchasing a CyberPower Systems Product. To enjoy all the features

and benefits of this Uninterruptible Power System (UPS), please read and follow all

installation and operation instructions completely. This UPS is designed to provide

guaranteed power protection for connected electronic equipment. The

accompanying PowerPanel Plus™ software saves data, closes open applications and

automatically shuts down your computer system in an intelligent and orderly manner.

PR1500/ PR2200

Guaranteed Uninterruptible Power System

IMPORTANT SAFETY WARNINGS

(SAVE THESE INSTRUCTIONS)

This manual contains important instructions that should be followed during installation and

maintenance of the UPS and batteries. Please read and follow all instructions carefully

during installation and operation of the unit. Read this manual thoroughly before attempting

to unpack, install, or operate.

CAUTION! The UPS must be connected to an AC power outlet with fuse or circuit

breaker protection. DO NOT plug the machine into an outlet that is not grounded. If you

need to de-energize this equipment, turn off and unplug the UPS.

CAUTION! DO NOT USE FOR MEDICAL OR LIFE SUPPORT

EQUIPMENT! CyberPower Systems does not sell products for life support or medical

applications. DO NOT use in any circumstance that would affect operation or safety of any

life support equipment, with any medical applications, or patient care.

CAUTION! The battery can energize hazardous live parts inside even when the AC

input power is disconnected.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and

humidity controlled indoor area, free of conductive contaminants. (Please see specifications

for acceptable temperature and humidity range).

CAUTION! To reduce the risk of electric shock, do not remove the cover, except to

service the battery. No user serviceable parts inside, except for the battery.

CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power

source before servicing the battery or installing a computer component.

CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire,

do not use with or near aquariums. Condensation from the aquarium can come in contact

with metal current contacts and cause the machine to short out.

CAUTION! DO NOT USE WITH LASER PRINTERS! The power demands of laser

printers are too large for a UPS.

INSTALLING YOUR UPS SYSTEM

UNPACKING

Inspect the UPS upon receipt. The box should contain the following:

(1) UPS Unit; (1) User’s Manual for UPS; (2) Rack mount Brackets; (2) Stands; (1) Telephone Cable

(1) PowerPanel PlusTM Software Disk; (1) User’s Manual for PowerPanel PlusTM;

(1) PowerPanelTM Software Disk; (1) User’s Manual for PowerPanelTM;

(2) Serial Interface Cable (DB-9); (1) Serial-to-USB cable; (1) Warranty Registration Card.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately upon receipt. However,

recharging the battery for at least four hours is recommended to insure

that the battery’s maximum charge capacity is achieved. Charge loss may

occur during shipping and storage. To recharge the battery, simply leave the

unit plugged into an AC outlet. The unit will charge in both the on as well as

the off position.

2. If you wish to use the software, connect the enclosed serial

interface cable to the serial port on the UPS and an open

serial port on the computer. If you would like to use USB

interface, please connect the USB adapter with the Serial

Cable then connect the USB to your computer.

3. With the UPS unit off and unplugged, connect your

computer, monitor, and any externally powered data storage device (Zip

drive, Jazz drive, Tape drive, etc…) into the battery power supplied outlets.

DO NOT plug a laser printer, copier, space heater, vacuum, paper shredder

or other large electrical device into the UPS. The power demands of these

devices will overload and possibly damage the unit.

4. To protect a fax, telephone, modem line or network cable, connect a telephone

cable or network cable from the wall jack outlet to the IN jack of the UPS. Then

connect a telephone cable or network cable from the OUT jack on the UPS to the

modem, computer, telephone, fax machine, or network device.

5. Plug the UPS into a 2 pole, 3 wire grounding receptacle (wall outlet). Make sure

the wall branch outlet is protected by a fuse or circuit breaker and does not

service equipment with large electrical demands (e.g. refrigerator, copier, etc…).

Avoid using extension cords. If used, the extension cord must be rated for 15

Amps.

6. Depress the power switch to turn the unit on. The power on indicator light will illuminate. If an

overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct

this, turn the UPS off and unplug at least one piece of equipment from the battery power supplied

outlets. Wait 10 seconds. Make sure the circuit breaker is depressed and then turn the UPS on.

7. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To

correct this, turn the UPS off, unplug at least one piece of equipment, wait 10 seconds, check to

make sure that the circuit breakers are depressed, and turn the unit on.

8. Your UPS is equipped with an auto-charge feature. When the UPS is plugged into an AC outlet, the

battery will automatically recharge. 2

PR1500/ PR2200

Guaranteed Uninterruptible Power System

9. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

10. To store your UPS for an extended period, cover it and store with the battery fully charged.

Recharge the battery every three months to insure battery life.

BASIC OPERATION

FRONT PANEL DESCRIPTION

 Power Switch

Press the power button to turn the UPS ON or OFF

 Test Switch Professional Rack Mount UPS performs a self-test automatically. When

powered on. When the UPS passes the test, it returns to on-line

operation. If the UPS fails the self-test, please recharge the battery for

hours and perform another self-test. If it fails after recharging the

battery, please replace the battery.

 Wiring Fault Indicator

This LED will illuminate to warn the user that a wiring problem exists

within the AC receptacle, such as a bad ground, miss ground or

reversed wiring. If illuminated, disconnect all equipment and contact

an electrician to insure outlet is properly wired.

 Battery Indicator This illuminates during utility failure, indicating that the battery is

supplying power to the battery-power supplied outlets.

 AVR Indicator This LED indicates that the UPS is operating in automatic voltage

regulation mode. When the led is illuminated continuously, it

indicates input over-voltage and the UPS unit bucks the voltage.

When the led is flashed in rotation, it indicates that the UPS unit

boosts input voltage.

Power On Indicator

This LED is illuminated when the utility condition is normal and the

UPS outlets are providing “clean power”, free of surges and spikes.

 Battery Indicators

This indicator shows a visual indication of the battery charge. If battery

capacity is under 20%, no indicator LED will illuminate and UPS starts

beeping.

 Load Level Indicators

This indicator shows a visual induction of the UPS load. The load indicator

LED will turn orange if the load is between 80 and 100%. If the load is

under 20%, no indicator LED will illuminate.

REAR PANEL DESCRIPTION

Circuit Breaker Reset for Overload Protection

Resettable circuit breakers provide optimal overload protection.

Battery Backup and surge Protection Outlets

The UPS provides four battery powered, surge protected and

AVR outlets for connected equipment and insures temporary

uninterrupted operation of connected equipment during a

power failure

 Individual Backup Power for Critical Load

The UPS provides two battery powered, surge protected and

AVR outlets for the most critical connected equipment and

insures temporary uninterrupted operation of connected

equipment during a power failure

NOTE: When the the UPS is overloaded, two circuit

breakers will be tripped to interrupt power supply to the

four battery outlets and leaves the two outlets for critical

loads uninterrupted.

PR1500/ PR2200

Guaranteed Uninterruptible Power System

Communication Protection Ports (RJ11/RJ45)

Ports protect standard modem, fax, telephone line or network

cable.

 Dual Serial Ports Professional Rack Mount UPS provides two serial ports to allow

connection and communication between the UPS and two

computers. This allows the simultaneous shutdown of two

computer systems.

The Primary computer (with PowerPanel Plus™ installed) is the computer that you will use

to control the UPS and make any changes to the operation of the UPS. The Secondary

computer (with PowerPanel™ installed) is unable to exhibit any control over the UPS.

When there is a power failure, the Primary computer will start to shutdown after a user

controlled delay. Once the Primary computer is shutdown, the UPS will signal the secondary

computer and initiate a shutdown. The secondary computer will then shutdown. Once the

secondary computer has completed its shutdown, the UPS will power off..

Both PowerPanel Plus™ and PowerPanel™ will save and close any open files prior to

shutting the system down.

BATTERY REPLACEMENT

Contact your dealer or call the number in this manual for information on battery replacement.

The order numbers for the battery are BA-PR1500 for PR1500; BA-PR2200 for PR2200

Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery.

Service the battery under the supervision of personnel knowledgeable of batteries and their

precautions. Servicing the battery can only be performed by trained personnel.

CAUTION! Use only the specified type of battery. See your dealer for replacement batteries.

CAUTION! The battery may present the risk of electrical shock. Do not dispose of batteries

in a fire, as they may explode. Follow all local ordinances regarding proper disposal of

batteries.

CAUTION! Do not open or mutilate the batteries. Release electrolyte is harmful to the skin

and eyes and may be toxic.

CAUTION! Abattery can present a high risk of short circuit current and electrical shock.

Take the following precautions before replacing the battery:

1. Remove all watches, rings or other metal objects.

2. Only use tools with insulated handles.

3. Do not lay tools or metal parts on top of battery or any terminals.

4. Wear rubber gloves and boots.

5. Determine if the battery is inadvertently grounded. If inadvertently grounded, remove

source of ground. CONTACT WITH GROUNDED BATTERY CAN RESULT IN

ELECTRICAL SHOCK! The likelihood of such shock will be reduced if such grounds

are removed during installation and maintenance (applicable to a UPS and a remote

battery supply not having a grounded circuit).

BATTERY REPLACEMENT PROCEDURE:

1. Remove the right side front

panel. 2. Remove the two retaining screws of

the cable protection cover then

remove the cover.

PR1500/ PR2200

Guaranteed Uninterruptible Power System

3. Disconnect the black and red cable. 4. Remove the four retaining screws.

5. Pull the battery pack out from the unit.

6. Slide a new battery pack into the unit.

Assemble the screws, cover, cable and

front panel in the reverse sequence of

above steps.

7. Recharge the unit for 4-8 hours to ensure the UPS performs expected runtime

DEFINITIONS FOR LED INDICATORS

Power

Wiring

Fault

AVR

Using

Battery

Circuit

Breaker

Alarm

Condition

On Off Off Off Set Off Normal

On Off Flash Off Set Off AVR- Max. boost 15% of input

voltage for output regulation

while input voltage is from 8% to

30% under nominal.

ON Off On Off Set Off

AVR- Max. buck 15% of input

voltage for output regulation

while input voltage is from 8% to

26% over nominal.

Off On/Off Off On Set Two

Beeps Utility Failure- The UPS is

providing battery power to the

Battery-Power Supplied outlets.

Off On/Off Off On Set Rapid

Beeps

Utility Failure- The UPS is

providing battery power.

Rapid beeps indicate the

battery will run out of charge

within a few minutes.

On/Off On/Off On/ Off

/Flash On/Off Set Long

Beep

Overload- Turn the UPS off

and unplug at least one piece of

equipment from the UPS. Wait

5 seconds, reset the circuit

breaker and restart the UPS.

Off Off Off On Up

Long

Beep

Overload- Turn the UPS off

and unplug at least one piece of

equipment from the UPS. Wait

5 seconds, reset the circuit

breaker and restart the UPS.

On On/Off

On/ Off

/Flash Off Set None

Weak Battery- Recharge the

battery for at least 8 hours. If

Check Battery is illuminated,

contact CyberPower Systems

for battery replacement

information.

Off Off Off Off Set Off

Surge Protection

Malfunction- Power surge has

damaged the unit. Please

contact CyberPower Systems

On/Off On On/ Off

/Flash On/Off Set/Up None

Electrical Wiring Fault-

Indicates wiring problems such

as a bad ground, missed

ground or reversed wiring

within the AC outlet. User is

advised to disconnect all

electrical equipment from the

outlet and have the outlet

checked by an electrician.

Otros manuales para PR1500

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unión Postal Universal de CyberPower

CyberPower

CyberPower CPS1500AVR Manual de usuario

CyberPower

CyberPower 649532715046 Manual de usuario

CyberPower

CyberPower STP3T10KE Manual de usuario

CyberPower

CyberPower UT1500E-FR/UPS Manual de usuario

CyberPower

CyberPower OM750ATLCD Manual de usuario

CyberPower

CyberPower Value1200EILCD Manual de usuario

CyberPower

CyberPower BU600E-FR Manual

CyberPower

CyberPower RT650 Manual de usuario

CyberPower

CyberPower BU600ELCD Manual de usuario

CyberPower

CyberPower Professional Rack Mount UPS 2200VA Manual de usuario

CyberPower

CyberPower OL6000ERT3U Manual de usuario

CyberPower

CyberPower UT1500EG Manual de usuario

CyberPower

CyberPower 649532018505 Manual de usuario

CyberPower

CyberPower LE850G Manual de usuario

CyberPower

CyberPower 6K On-Line series Manual de usuario

CyberPower

CyberPower Smart App Sinewave PR2200LCD Manual de usuario

CyberPower

CyberPower BU600E-AS Manual de usuario

CyberPower

CyberPower 649532808007 Manual de usuario

CyberPower

CyberPower Value 600E-GP Manual de usuario

CyberPower

CyberPower CyberShield CS24C12V-E Manual de usuario

CyberPower

CyberPower 649532110001 Manual de usuario

CyberPower

CyberPower CST1500S Manual de usuario

CyberPower

CyberPower OLS6KERT4UA Manual de usuario

CyberPower

CyberPower STANDBY UPS Series Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario

ZincFive

ZincFive BC Series Manual de usuario

BPC

BPC 1.5K SMART Manual de usuario

IBM

IBM 5595-1AX Manual de usuario