CyberData V3 Keypad Manual de usuario

Quick Start Guide 930521A

1.0 Out-of-Box and Prior to Final Installation

1.1. Verify that you have received all of the parts listed on the Installation Quick

Reference placemat.

1.2. Download the current manual, otherwise known as an Operation Guide,

which is available on the Documentation page at the following website

address:

http://www.cyberdata.net/products/voip/digitalanalog/intercomkeypadv3/docs.html

Note You can also navigate to the Documentation page by going to

www.CyberData.net and following the steps that are indicated by

the following figures:

2.0 Select Power Source

PoE Switch PoE Injector

Set PoE power type to Class 0 = 15.4W CAT6 cable recommended—

for longer distances

Be sure you are using a non-PoE switch or port

Make sure port is not in trunk mode

Set port to full duplex/ 100mbps

Spanning Tree Protocol (STP) must be disabled or Portfast enabled

V3 Keypad Outdoor Intercom

Quick Start Guide

The IP Endpoint Company

VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Quick Start Guide 930521A

3.0 Power Test

3.1. Plug in the CyberData device and monitor the LED activity above the

ethernet port on the back of the Intercom. See the following figure:

3.2. The green Link LED blinks off once during the boot up process and then

comes on again and remains constant (solid green). The yellow Activity

LED may be blinking depending on the network activity.

During the initialization process, the green Call Button LED should come

on and be constant (solid green). After the Intercom has completed booting,

the LED will blink twice and then remain constant thereafter (either on or

off depending on whether or not the Button Lit When Idle setting is

enabled on the Device Configuration page).

Normally, the initialization process will take about 20 seconds. However, if

the device is set to use DHCP and no DHCP server is available, then the

device will retry for the amount of time specified in the DHCP Timeout in

seconds setting on the Network Configuration page before it falls back to

the stored static IP address (10.10.10.10 by default).

3.3. When the Intercom has completed the initialization process, press and hold

the RTFM switch (SW1 button) for 3 seconds to announce the IP address.

This concludes the power test. Go to Section 4.0, "Connecting to a Network

in a Test Environment".

Link LED

Activity LED

VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Quick Start Guide 930521A

4.0 Connecting to a Network in a Test Environment

Note The following connections are usually needed for this procedure:

•PC

• PoE switch or injector

•CyberDatadevice

4.1. In a test environment, use a PC that is connected to the same switch as a

single CyberData device. Note the subnet of the test PC.

4.2. Use the CyberData Discovery Utility program to locate the device on the

network. You can download the Discovery Utility program from the

following website address:

http://www.cyberdata.net/support/voip/discovery_utility.html

4.3. Wait for initialization to complete before using the Discovery Utility

program to scan for a device. The device will show the current IP address,

MAC address, and serial number.

4.4. Select the device.

Note If the IP address of the device is in the same subnet of the PC, then

go to Step 4.7.

4.5. If the IP address of the device is different from the subnet of the PC, then

complete the following steps:

4.5.1. Click the Details tab.

4.5.2. Click Adv. Config to manually configure settings with an available IP

address in the same subnet.

Note A gateway address of 0.0.0.0 or a subnet address of

255.255.255.255 will prompt you to enter a valid address.

4.5.3. Click OK after you are finished making changes.

4.6. A dialog box will prompt you to click OK after confirming the configuration

changes and will ask you to wait while the device reboots. Please wait for

the device to power up and wait for the Discovery Utility program to find

the device on the network.

VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Quick Start Guide 930521A

4.7. After the Discovery Utility program has located the device on the network,

click Launch Browser . When the IP address matches the subnet of the PC

that you are using to access the device, the Discovery Utility program will

be able to launch the browser window which is configured to the device’s IP

address.

4.8. Log on to the web interface by using the default username (admin) and

password (admin) to configure the device.

4.9. Perform an audio test by pressing the Te st A ud i o button that is located at

the bottom of the Device Configuration page. If the audio test message is

clearly audible, then your CyberData device is functioning properly.

4.10. The device is now ready to be set for your desired network configuration.

You may reference our IP-PBX specific configurations at the following

website address:

http://www.cyberdata.net/support/server/index.html

5.0 Contacting CyberData VoIP Technical Support

For quality assurance purposes, we ask that you please visit our website and

complete our Support Form which is available at the following website address:

http://www.cyberdata.net/support/contactsupportvoip.html

Note You can also navigate through menus to the Support Form by going to

www.CyberData.net as shown in the following figure:

The Support Form initiates a ticket which CyberData uses for tracking customer

requests. Most importantly, the Support Form tells us which PBX system and

software version that you are using, the make and model of the switch, and other

important information. This information is essential for troubleshooting. Please

also include as much detail as possible in the Comments section of the Support

Form.

Requests for Returned Materials Authorization (RMA) numbers require an active

VoIP Technical Support ticket number. A product will not be accepted for return

without an approved RMA number.

VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Otros manuales para V3 Keypad

Tabla de contenidos

Otros manuales de Sistema de intercomunicación de CyberData

CyberData

CyberData 11113 Manual

CyberData

CyberData 11113 Manual de usuario

CyberData

CyberData 11111 Manual de usuario

CyberData

CyberData VoIP Intercom 010935F Manual de usuario

CyberData

CyberData VoIP Indoor Intercom 011030 Manual de usuario

CyberData

CyberData 011478 Manual de usuario

CyberData

CyberData 011211 series Manual

CyberData

CyberData VoIP Indoor Intercom 011030 Manual

CyberData

CyberData 011309 Manual de usuario

CyberData

CyberData VoIP Indoor Intercom 011030 Manual de usuario

CyberData

CyberData #011123 Manual

CyberData

CyberData 11186 Manual de usuario

CyberData

CyberData 11304 Manual de usuario

CyberData

CyberData 011211 series Manual

CyberData

CyberData 11035 Manual de usuario

CyberData

CyberData 011307 Manual

CyberData

CyberData VoIP Intercom 010935B Manual de usuario

CyberData

CyberData 11308 Manual

CyberData

CyberData 011410 Manual

CyberData

CyberData 11111 Manual de usuario

CyberData

CyberData 11186 Manual de usuario

CyberData

CyberData VoIP Desktop Intercom Manual

CyberData

CyberData 11035 Manual de usuario

CyberData

CyberData 11035 Manual de usuario

Manuales populares de Sistema de intercomunicación de otras marcas

Bticino

Bticino LINEA 3000 Manual de usuario

MSI

MSI MSI-140 Manual de usuario

golmar

golmar Stadio Plus Manual de usuario

Vidos

Vidos duo M1021 Manual de usuario

Vimar

Vimar ELVOX 7539/E Manual de usuario

SSS Siedle

SSS Siedle BTSV 850-03 Manual de usuario

Dahua

Dahua VTO Series Manual de usuario

Elvox

Elvox 5651 Manual de usuario

Videx

Videx VIDEOKIT Series Manual de usuario

Rocom

Rocom Doortello Business FW T2.05W2.04 Manual de usuario

Viking

Viking E-35-EWP Manual de usuario

Safeguard Supply

Safeguard Supply LRA-EX1000 Manual de usuario

SSS Siedle

SSS Siedle BFCV 850 Series Manual de usuario

GRD

GRD MAX V2 Manual de usuario

Alecto

Alecto ADI-250 Manual de usuario

Aiphone

Aiphone IE-8MD Manual de usuario

Perel

Perel EDB4 Manual de usuario

Bticino

Bticino Classe 300 Manual de usuario