Specifications
Culligan Silver Series™Water Conditioners with Time Clock, Aqua-Sensor®Device or Soft-Minder®Meter
9” Model 12” Model
Control Valve 5-cycle, Reinforced Thermoplastic 5-cycle, Reinforced Thermoplastic
Overall Conditioner Height 51 in 51 in
1 295 mm 1 295 mm
Media Tank Dimensions (Dia x Ht) 9 x 45 in 12 x 45 in
229 x 1 143 mm 305 x 1 143 mm
Salt Storage Tank Dimensions (Dia x Ht) 16 x 43 in 18 x 43 in
406 x 1 092 mm 457 x 1 092 mm
18 x 43 in
457 x 1092 mm
Exchange Media, Type and Quantity Cullex®Media, 0.86 ft3Cullex®Media, 1.4 ft3
Cullex®Media, 24.5 L Cullex®Media, 40 L
Underbedding, Type and Quantity Cullsan®Underbedding, 12 lb Cullsan®Underbedding, 30 lb
Cullsan®Underbedding, 5.4 kg Cullsan®Underbedding, 14 kg
Exchange Capacity 17,500 gr @ 4.0 lb 24,100 gr @ 6.0 lb
@ Salt Dosage Per Recharge11 133 g @ 1.8 kg 1 560 g @ 2.7 kg
23,900 gr @ 8.0 lb 34,500 gr @ 12.0 lb
1 547 g @ 3.6 kg 2 234 g @ 5.4 kg
26,600 gr @ 12.0 lb 41,900 gr @ 18.0 lb
1 722 g @ 5.4 kg 2 713 g @ 8.1 kg
Efficiency rated dosage14 380 gr/lb 4 010 gr/lb
626 g/kg 573 g/kg
Freeboard to Media216.6-17.6 in 17.5-18.5 in
420-447 mm 444-470 mm
Freeboard to Underbedding339.2 in 38.5 in
996 mm 978 mm
Salt Storage Capacity 250 lb or 375 lb 375 lb
114 kg or 170 kg 170 kg
Rated Service Flow @ Pressure Drop 7.5 gpm @ 15 psi 7.5 gpm @ 13 psi
30 Lpm @ 102 kPa 28 Lpm @ 90 kPa
Total Hardness, Maximum 75 gpg 99 gpg
1 283 mg/L 1 692 mg/L
Total Iron, Maximum 5 ppm 5 ppm
5 mg/L 5 mg/L
Hardness to Iron Ratio, Minimum 8 gpg to 1 ppm 8 gpg to 1 ppm
140 mg/L to 1 mg/L 140 mg/L to 1 mg/L
Operating Pressure 20-125 psi 20-125 psi
140-860 kPa 140-860 kPa
Operating Temperature 33-120°F 33-120°F
1-50°C 1-50°C
Electrical Requirements 24V/60Hz 24V/60 Hz
Electrical Power Consumption, Min/Max 3 Watts/35 Watts 3 Watts/35 Watts
Drain Flow, Maximum42.3 gpm 3.5 gpm
9 Lpm 14 Lpm
Recharge Time, Average580 min 85 min
Recharge Water Consumption, Average 40 gal 82 gal
170 L 325 L
1 The efficiency rated dosage is only valid at the 4 lb. salt dosage for the 9" models and 6 lb. for the 12" models.
2 Measured from top of media to top surface of tank threads (backwashed and drained).
3 Measured from top of underbedding to top surface of tank threads.
4 Backwash at 120 psi (830 kPa).
5 10 minute backwash, 4 lb (1.8 kg) 9” model or 6 lb (2.7 kg) 12” model salt dosage. SPECIFICATIONS 3
