CTC Union FMUX03/V35 Manual de usuario

FMUX03/V35

Table of Content

Chapter 1 Introduction………………………………….…………………… 3

1-1 Functional Description………………..……………………… 3

1-2 Application of FMUX03/V35………………………………… 4

1-3 Technical Specification …………………..….……………… 4

1-4 FMUX03/V35 Ordering information ..……………………….. 7

Chapter 2 Installation ………………………………………………………… 8

2-1 Description…………………………………………….……… 8

2-2 Unpacking………………………………………….………… 8

2-3 Site Requirements………………………..…………………… 8

2-4 Site Selection……………….…………………………………. 9

2-5 AAC or DC Electrical Outlet Connection…………………….. 9

Chapter 3 Operating Instructions.……………………………………………. 10

3-1 Front Panel……………….……………………………………. 10

3-2 Rear Panel Control and LED Indicator Function..……….….. 11

3-3 Menu Tree…………………………………………………….. 13

Chapter 4 Operating and Setup Instructions…………………………………. 14

4-1 Profile…………………………………………………………. 14

4-2 System Configuration…………….…………………………… 15

4-3 Alarm Status Report………………..…………………………. 15

4-4 Craft Port Operation…………………………………………... 15

4-5 How to Connect and setup the craft port …………………….. 15

4-6 Operating From The Craft Port ………………………………. 16

Chapter 5 Loopback Test…………………………………………………….. 24

5-1 General Information………………………………………..… 24

5-2 Loopback Test (For V.35 Tributary)………………………….. 25

Appendix-A DB25 male connector To M34 female connector 26

FMUX03/V35

Chapter 1 Introduction

1-1 Functional Description

The CTC Union FMUX03/V35 utilizes V.35 interface to convert electric signal

into optical signal and extends its transmission distance up to 80 kilometers.

FMUX03/V35 provides user-friendly functions for monitoring, maintaining, and

configuring the unit using LCD panel and VT-100 remote terminal access. Its DC /

AC selectable power source insures a quality and reliable power supply. CTC Union

FMUX03/V35 provides the telecommunication industry a multipurpose and easy to

use high quality fiber optics modem.

 Operating from either AC or DC power module , backup power supply is

available.

 Mountable on either 19-inch or 23-inch rack.

FMUX03/V35

1-2 Application of FMUX03/V35

FMUX03/V35 is mainly used to extend the transmission distance of optical signal by

multiplexing individual channels into a single optical stream using V.35 interface. In

addition, FMUX03/V35 can connect a client equipment to a Central Office using V.35

interface.

Application of FMUX03/V35

FMUX03/V35

1-3 Technical Specification

 V.35/V.36/EIA530A/RS232(V.28)/V.10/V.11/X.21/RS449 Interface

 Bit Rate: N*64K (N=1 to 32) up to 2M

 Number of Input Ports: V.35 ports

 Clock Source: Internal, DTE (selectable), Line

 Optical Interface

 Optical Source: 1310/1550 nm MLM Laser

 Number of Optical Links: 2 (1+1 auto protection switch)

 Output Power: > -12dBm at 9/125 (Laser 1310 nm)

> -12dBm at 9/125(Laser 1550 nm)

 Receiver Sensitivity: -34dBM (1310nm/1550 Laser)

 System Gain: 20-30dB

 Fiber Type: Single Mode (9/125um)

 Optical Connector: FC/PC；ST

 Alarm Detection and Indication

 Data port Interface

 TxD (Transmit data):DTE transmit data to DCE

 RxD(Receive data):DCE transmit data to DTE

 CTS(Clear to send):DCE to DTE

 RTS(Request to send):DTE to DCE

 Optical Interface

 LOS (Loss of Signal)：The loss of optics signal

 Laser On: Laser On indicator

 Alarm Indication

 Major alarm: loss of frame,loss of clock,loss of signal

 Minor alarm: one of power modules fail or receive RDI signal from

Opticallink

 Alarm Connector

 DB-9 female connector

 Connect to an external BUZZER to receive visible and audible alarm.

FMUX03/V35

 Diagnostic Capabilities and Loopback Function

 Optical Interface: Local Loopback and Remote Loopback

 Data port Interface: Local Loopback and Remote Loopback

 ACO: Alarm cut off

 RST: Rest button

 Configuration

 Use the 3 control buttons and the LCD front panel to configure and

monitor the system

 Craft port with DCE appearance

 Bits per second (baud): 9600bps

 Parity: None

 Data Bits: 8 bits

 Stop Bit: 1

 Power

 DC: -36V ~ -72VAC: 90V ~ 288V(57Hz ~ 63Hz)

 Physical Specifications

 FMUX03/V35 Dimensions:

 Depth: 220 mm

 Width: 285 mm

 Height: 44.5 mm

 Optical Link: FC/PC or ST, Electrical Link: DB-25 female connector

 Alarm Connector: DB-9 connector

 Environment

 Operating Temperature: 0 ~ 40℃Indoor Version

-25 ~ 70℃Storage

 Humidity: 5 ~ 95%

FMUX03/V35

1-4 FMUX03/V35 Ordering Information

Options for Ordering information

Optical Module

1310S 1310 nm single-mode, loop reach up to 45km (Single OE Module) > -12dBm

1550S 1550 nm single-mode, loop reach up to 75km (Single OE Module) > -12dBm

1310D 1310 nm single-mode, loop reach up to 45km (Dual OE Module) > -12dBm

1550D 1550 nm single-mode, loop reach up to 75km (Dual OE Module) > -12dBm

System Gain

L(Low power) System Gain ＞16dB

M(Low power) System Gain ＞20dB

H(Low power) System Gain ＞25dB

Power Module

AC-1 Single 90 ~ 288 VAC power supply

DC-1 Single –34 ~ -72 VDC power supply

AC-2 Dual 90 ~ 264 VAC power supply

DC-2 Dual –34 ~ -72 VDC power supply

AC-1, DC-1 AC / DC dual power supply

Optical Connector

F FC type fiber connector

T ST type fiber connector

V.35 Connector

1 Ch 1 set of V.35 connector

FMUX03/V35

Chapter 2 - Installation

2-1 Description

This chapter provides the information needed to install FMUX03/V35. It is

important to follow the installation instruction to insure normal operation of the

system and to prevent damage due to human error.

2-2 Unpacking

If there is a possibility for future relocation of the FMUX03/V35 unit, please save the

cartons and protection packaging material. The following items are shipped with

your FMUX03/V35:

 One FMUX03/V35 User’s Manual

 One FMUX03/V35 Unit

 V.35 Cable (DB25 to M34)

Please carefully unpack and inspect the unit and accessories for damaged and missing

parts. Contact our nearest sales representative or our company directly if you suspect

any damaged or missing parts. Improper handling during shipment may cause early

failure.

2-3 Site Requirements

The FCC requires telecommunication equipment to withstand electrical surge that

may result from lighting strikes. This equipment has been tested and found to

comply with the FCC requirement. Users should follow the precaution below to

insure the safety and minimize the risk of damage to the equipment:

 Make sure that the power outlet is properly grounded. Please refer to article 250

of the National Electrical Code (NEC) Handbook.

 Proper grounding should include a minimum of:

1) A grounded rod buried outside the building at least 8 feet (2.44 meters) deep.

2) It is preferred that the building uses metal water pipe and cooper connector at

the joint.

FMUX03/V35

3) Any device either connected to FMUX03/V35 directly or indirectly should use

the same set of power outlet.

2-4 Site Selection

For best performance, install the FMUX03/V35 within 50 feet (15.24 meters) from

the data terminal equipment and 6 feet (1.83 meters) from the AC power outlet. To

allow easy access to the equipment, leave at least 36 inches (90 cm) clearance in front

and at least 4 inches (10.2 cm) at the rear.

To avoid overheating, leave at least 1 inch (2.5 cm) on either side of FMUX03/V35.

Also, do not stack another equipment on top of FMUX03/V35.

2-5 AC or DC Electrical Outlet Connection

For safety and to prevent damage to FMUX03/V35, make sure that the power

requirement matches those of your electric outlet. Connect power to FMUX03/V35

and power on the equipment.

FMUX03/V35

Chapter 3 – Operating Instructions

3-1 Front Panel

There are four parts to the front panel of FMUX03/V35:

(1) Fiber Optics Connectors and Indicators: Notifies user of a problem such as

LOS (Loss of Signal) and Laser LED (LSR). Includes a pair of

input/output connector

(2) Alarm LED Display: Notifies users of a problem such as a Major Alarm

(MAJ), Minor Alarm (MIN), and System Alarm (SYS).

(3) LCD Control Buttons: The three buttons, ▲, ▼, and are used for

system configuration and for the loopback test.

(4) V.35 Port Status LED: Four LEDs, representing TXD, RXD, CTS, and

RTS.

Each of the LED indicators is described below in detail:

Front panel

Fiber Optics

Connector

LED Display

LCD Control

Button

LCD Panel

Tabla de contenidos

Otros manuales de Multiplexor de CTC Union

CTC Union

CTC Union FRM220-FOM04 Manual de usuario

CTC Union

CTC Union ETU01C Manual de usuario

CTC Union

CTC Union ERM-MUX/PLUS Manual de usuario

CTC Union

CTC Union FMUX-01A Manual de usuario

CTC Union

CTC Union FMUX04 Manual de usuario

CTC Union

CTC Union EOC-20 Manual de usuario

CTC Union

CTC Union FMUX80 Manual de usuario

CTC Union

CTC Union IPM-4SE Manual de usuario

CTC Union

CTC Union FRM220-MX210 series Manual de usuario

CTC Union

CTC Union FMUX-01A Manual de usuario

CTC Union

CTC Union FRM220-FOM01 Manual de usuario

CTC Union

CTC Union ERM-MUX Manual de usuario

CTC Union

CTC Union FMUX03 Manual de usuario

CTC Union

CTC Union FMUX-01 Manual de usuario

Manuales populares de Multiplexor de otras marcas

Campbell

Campbell AM416 Manual de usuario

Paradyne

Paradyne SIM2000 Manual de usuario

Panasonic

Panasonic WJFS616 - SWITCHER Manual de usuario

Lanex

Lanex TM-77 Manual de usuario

Bosch

Bosch VSS8394/01T Manual de usuario

Quark-Elec

Quark-Elec QK-A035 Manual de usuario

ADTRAN

ADTRAN Frameport 768 Manual de usuario

Elo TouchSystems

Elo TouchSystems E247 Manual de usuario

Paradyne

Paradyne Hotwire 8786 Manual de usuario

RFL Electronics

RFL Electronics 9508D UCC Manual de usuario

Miranda

Miranda AMX-101i Manual de instrucciones

ShipModul

ShipModul MiniPlex-AIX NMEA-0183 Manual de usuario

GE StoreSafe SDVR-10 Manual de usuario

Pickering

Pickering 40-613 Manual de usuario

Pickering

Pickering 40-667C Manual de usuario

American Fibertek

American Fibertek MTX-8410C Manual de usuario

ADC

ADC HiGain ELU-319 5E Manual de usuario

Paradyne

Paradyne Hotwire 8774 Manual de usuario