CSL CS101 Guía de inicio rápido
Special Note – Restore CS101 OS to
Factory Default Setting
Version 1.2.1
CSL: The One-Stop-Shop for RFID Solutions
Special Note – Restore CS101 OS to Factory Default Setting v1.2.1
Copyright © Convergence Systems Limited, All Rights Reserved
2
Table of Contents
1
Introduction ......................................................................................................................................................... 3
2
Restore CS101 OS to Factory Default Setting Overview .................................................................................... 4
3
Restore CS101 OS to Factory Default Setting Procedure.................................................................................... 5
4
Install Basic Components .................................................................................................................................... 9
5
Install CS101 Demo App ................................................................................................................................... 14
Special Note – Restore CS101 OS to Factory Default Setting v1.2.1
Copyright © Convergence Systems Limited, All Rights Reserved
3
1 Introduction
This document provides guidelines to the user to restore the software to factory default in the
CSL CS101 Reader. The following areas will be covered in this document
- Restore of the Windows CE OS on CS101
- Installation of the CS101 Basic Components Installers
- Installation of demo application
Special Note – Restore CS101 OS to Factory Default Setting v1.2.1
Copyright © Convergence Systems Limited, All Rights Reserved
4
2 Restore CS101 OS to Factory Default Setting Overview
The flow diagram below shows the priority of firmware upgrade steps starting from device
application and default setting file. User MUST follow the sequence below to restore Win CE
OS to Factory Default Setting. DO NOT FORGET ANY STEP.
Restore system to factory default setting
Do Touch Screen calibration for CS101.
Install Basic Components (Drivers, Dot Net Framework, etc.)
Install CS101 Demo App, Latest Version
Set Barcode Power Save Mode.
Special Note – Restore CS101 OS to Factory Default Setting v1.2.1
Copyright © Convergence Systems Limited, All Rights Reserved
5
3 Restore CS101 OS to Factory Default Setting
Procedure
1. Use a fully charged battery to power on CS101
2. Press and keep holding the “Power” key for 1 second
Special Note – Restore CS101 OS to Factory Default Setting v1.2.1
Copyright © Convergence Systems Limited, All Rights Reserved
6
3. WHILE holding the “Power” key, press “Reset” key simultaneously for 5 seconds.
4. After that, ONLY release the “Reset” key, leaving the Power key still pressed by finger. Keep
holding the key and wait until warning box is seen (after 5 seconds).
5. After warning box (Restore system to factory default) is seen, release the “Power” key.
Press [Yes] to continue.
Special Note – Restore CS101 OS to Factory Default Setting v1.2.1
Copyright © Convergence Systems Limited, All Rights Reserved
7
6. Press [Yes] when reconfirmation box appears.
7. Press [OK] button to confirm the System ROM formatting.
8. Wait until System ROM formatting process is finished.
Special Note – Restore CS101 OS to Factory Default Setting v1.2.1
Copyright © Convergence Systems Limited, All Rights Reserved
8
9. It will then automatically go to a touch screen calibration screen.
Use the Pen CS101 provided to do the Calibration.
10. Tap the screen to confirm the calibration settings.
11. After the 1st Touch Screen calibration for CS101, wait until CS101 enters Win CE.
12.Please go to Section 4 to Install Basic Components for CS101.
Special Note – Restore CS101 OS to Factory Default Setting v1.2.1
Copyright © Convergence Systems Limited, All Rights Reserved
9
4 Install Basic Components
Just upgrading the WinCE OS is not enough. The user needs to install the internal USB driver
connecting the host processor to the RFID module inside, Dot Net Framework, Demo App, etc.
1. After the Win CE OS is upgraded, wait until CS101 enter Win CE.
2. Unzip the package CS101 Basic Components Installers.zip (provided by CSL) in PC to a
directory.
3. Copy the complete directory CS101 Basic Components Installers from PC to CS101 via SD
card or USB connection (For USB connection, you need to run ActiveSync or Windows Mobile
Device Center) .
Special Note – Restore CS101 OS to Factory Default Setting v1.2.1
Copyright © Convergence Systems Limited, All Rights Reserved
10
4. Open the folder inside CS101 Win CE.
5. Check the files in
“CS101 Basic Components Installers”
. They are RfidUsbDriverCE.cab,
NETCFv2.wce5.armv4i.cab, NETCFv35.wce.armv4.cab,
BarcodeSavePowerModeSetup21-Oct-2009.CAB and sqlce30.wce5.armv4i.cab.
Otros manuales para CS101
1
Tabla de contenidos
