Crestron GREEN LIGHT Power Switching Manual de usuario

CRESTRON GREEN LIGHT™ Power Switching

Introduction

CRESTRON GREEN LIGHT power switching cabinets come pre-configured with GLXP modules already installed.

The cabinets only require installation and wiring of feed and load circuits.

Industry Compliance

The cabinet and modules are Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.

(E227280 (cabinet) and E103692 (modules))

Application

The following diagram shows CRESTRON GREEN LIGHT cabinets in a lighting application that is controlled by

an IPAC system.

CRESTRON GREEN LIGHT Power Switching Cabinets in a Typical Lighting Application

Crestron Electronics, Inc. Installation Guide – DOC. 6672B

15 Volvo Drive Rockleigh, NJ 07647 (2020570)

Tel: 888.CRESTRON 10.08

Fax: 201.767.7576 Specifications subject to

www.crestron.com change without notice.

Power Switching CRESTRON GREEN LIGHT™

Physical Description

This section shows the exterior and interior dimensions of the CRESTRON GREEN LIGHT cabinet.

External Dimensions of CRESTRON GREEN LIGHT Power Switching Cabinets

KNOCKOUT

(FOR 34" (19 MM) CONDUIT)

TYPICAL BOTH SIDES

TECHNICAL KNOCKOUTS, 50 TOTAL

(FOR 34" (19 mm) &12" (13 mm) CONDUIT)

TYPICAL TOP & BOTTOM

6 58"

(169 mm)

20"

(508 mm)

OPTIONAL DOOR

Ø 516"

(8 mm)

2 12"

(64 mm) 15"

(381 mm)

Ø 58"

(16 mm)

Ø 716"

(12 mm)

External Dimensions of CRESTRON GREEN LIGHT Power Switching Cabinets

DIMENSION 12 Breaker 30 Breaker 42 Breaker 42 Breaker (Short)

H1 37 1/2” 953 mm) 70” (1.8 m) 90” (2.3 m) 78 15/16” (2 m)

H2 3” (77 mm) 3 5/8” (93 mm) 3 5/8” (93 mm) 3 5/8” (93 mm)

H3 32 7/8” (836 mm) 59 3/8“ (1.5 m) 79 3/8” (2.0 m) 66" (1.7 m)

2 •CRESTRON GREEN LIGHT Power Switching Installation Guide – DOC. 6672B

CRESTRON GREEN LIGHT™ Power Switching

Interior Dimensions of CRESTRON GREEN LIGHT Cabinets (120/208 VAC, left; 277/480 VAC, right)

H1 H1

1 78"

(48 mm)

818"

(207 mm)

1 78"

(48 mm)

614"

(159 mm)

(51 mm) 2"

(51 mm)

(204 mm)

3 78"

(99 mm)

Interior Dimensions of CRESTRON GREEN LIGHT Cabinets

120 Service 277 Service

DIMENSION 12 Breaker 30 Breaker 42 Breaker 12 Breaker 30 Breaker 42 Breaker

H1 8 3/4”

(223 mm) 15 1/8”

(385 mm) 18 1/8”

(461 mm) 7 1/16”

(180 mm) 12 1/16”

(310 mm) 15 1/16”

(383 mm)

Installation Guide – DOC. 6672B CRESTRON GREEN LIGHT Power Switching •3

Power Switching CRESTRON GREEN LIGHT™

Installation

Observe the following when installing the cabinet:

•The cabinet must be mounted by a licensed electrician in accordance with all national and local codes.

Refer to the diagram below for specific requirements.

•The cabinet is designed for surface mounting on a wall.

•Cabinets are intended for indoor use only.

•The ambient temperature range should be 32°F to 104°F (0°C to 40°C). The relative humidity should range

from 10% to 90% (non-condensing). Allow adequate clearance in front of the cover for servicing.

Mounting Location

MAXIMUM HEIGHT OF

HIGHEST BREAKER

(FROM GROUND)

(0.9 m)

6'-7"

(2.01 m)

MINIMUM REQUIRED

CLEARANCE

WALL

4 •CRESTRON GREEN LIGHT Power Switching Installation Guide – DOC. 6672B

CRESTRON GREEN LIGHT™ Power Switching

Wiring

NOTE: All wiring must be installed in accordance with all local and national electrical codes.

NOTE: Refer to the torque settings specified on pages 6, 7 and 8.

CRESTRON GREEN LIGHT cabinets are shipped with GLXP modules installed and prewired to the branch circuit

breakers. The following must be performed after installation:

•Connect incoming feed conductors to the breaker panel (section Aof the following diagram)

•Connect load wiring to GLXP module outputs (section Bof the following diagram)

•Connect control wiring (section Cof the following diagram)

CLASS 2

WIRING ONLY

CLASS 2

WIRING ONLY

FEED:

3-PHASE 4-WIRE TO LOADS:

2W + GND 16A (MAX)

Installation Guide – DOC. 6672B CRESTRON GREEN LIGHT Power Switching •5

Power Switching CRESTRON GREEN LIGHT™

Feed Wiring (Section A)

Feed Wiring for MLO (left) and MCB (right) Applications

Refer to the following table for information on wiring the feed to the panel.

Feed Wire Information

120 Volt Models 277 Volt Models

TERMINAL CONNECTOR MAX

WIRE RANGE TORQUE Max

Current CONNECTOR MAX

WIRE RANGE TORQUE Max

Current

Neutral and

Main Lugs 10-2/0 AWG (CU) or

6-2/0 AWG (AL)

6 - 300 kcmil (CU or AL)

15 lb-ft

(20.3 Nm)

21 lb-ft

(28.5 Nm)

6-350 kcmil (CU or AL)

1/0-750 kcmil (CU or AL) 275-300 lb-in

(31.1-33.9 Nm)

Neutral Bus 14-10 AWG(CU) or

12-10 AWG (AL)

8 AWG (CU or AL)

6-4 AWG (CU or AL)

20 lb-in

(2.3 Nm)

25 lb-in

(2.8 Nm)

35 lb-in

(4.0 Nm)

225

Amps 14-6 AWG (CU or AL)

14-2/0 AWG (CU or AL)

24-35 lb-in

(2.7-4.0 Nm)

40-50 lb-in

(4.5-5.6 Nm)

250

Amps

Use copper or aluminum conductors only – rated 75°C.

WARNING: Failure to properly tighten lugs may result in poor electrical connection and overheating of the terminals.

6 •CRESTRON GREEN LIGHT Power Switching Installation Guide – DOC. 6672B

CRESTRON GREEN LIGHT™ Power Switching

Load Wiring (Section B)

CAUTION: Bypass jumpers are provided on each output to allow testing and to protect the module during

installation. The jumper shorts the Land SW terminals so that the load circuit is energized when the branch breaker

is on. Do not remove the bypass jumper until all feed and load wiring has been completed, and the circuits have been

tested for electrical faults.

NOTE: Use copper conductors only – rated 75°C.

Wire Gauge and Torque Values

TERMINAL CONNECTOR MAX WIRE RANGE TORQUE STRIP LENGTH

LOAD OUTPUTS 14-10 AWG 4.43 lb-in

(0.5 Nm) 5/16”

(8 mm)

DIM CONTROL

(GLXP-DIMFLV8 only) 28-12 AWG 4.43 lb-in

(0.5 Nm) 5/16”

(8 mm)

GROUND BAR 14-10 AWG 35 lb-in

(4.0 Nm) 5/16”

(8 mm)

GROUND LUG 14-4 AWG 45-25 lb-in

(5.1-2.8 Nm) 3/4"

(19 mm)

1. Each output has a label with the number of the controlling circuit breaker printed on it. With the

corresponding circuit breaker turned off, connect the controlled circuit (LOAD) wires to the output per the

markings on the module as shown in the following diagrams. Terminals for load wiring accept one 10 – 14

AWG wire.

Load Wiring for GLXP-SW10, GLXP-SW16, GLXP-HSW8, GLXP-HSW12, and GLXP-DIMFLV8 (Jumper Installed)

1.2000

CIRCUIT BREAKER (20A MAX)

NEUTRAL

BUS TO LOADS

TO NEUTRAL BUS (PREWIRED)*

TO BRANCH BREAKER (PREWIRED)

TO LOAD

JUMPER (PREWIRED)

* A NEUTRAL connection is only present on OUTPUT 1.

Installation Guide – DOC. 6672B CRESTRON GREEN LIGHT Power Switching •7

Power Switching CRESTRON GREEN LIGHT™

The GLXP-DIMFLV8 also requires wiring the terminals for 0-10 VDC control wire. Refer to the following

diagram when connecting the dimmable ballast. Each control wire terminal accepts one 12 – 28 AWG wire.

0-10 VDC Control Wiring for GLXP-DIMFLV8 Only

TO + ON 4-WIRE LOADS (PURPLE)

TO - ON 4-WIRE LOADS (GRAY)

2. Test the circuit for electrical faults by turning on each circuit breaker, checking that the breakers do not

trip, and that power is delivered to the proper loads.

3. Turn off the circuit breaker(s) and remove all jumpers.

4. Turn on the circuit breakers.

Control Wiring (Section C)

The bottom of the cabinet contains Cresnet®connections for interfacing to the rest of the Crestron®control system.

It also provides an override input which can be tied to devices such as the GLS-PLS-120/277 phase-loss sensor, or

other devices that provide a dry contact closure (manual switch, fire alarm relay, etc.).

NOTE: Interface connectors for NET (x2), POWER (x1), and OVERRIDE (x1) ports are provided.

Wire Gauge and Torque Values

TERMINAL CONNECTOR MAX

WIRE RANGE TORQUE STRIP

LENGTH

NET 12 AWG 4.43 lb-in

(0.5 Nm) 1/4”

(6 mm)

POWER 26-12 AWG 4.43 lb-in

(0.5 Nm) 1/4”

(6 mm)

OVERRIDE 26-12 AWG 4.43 lb-in

(0.5 Nm) 1/4”

(6 mm)

8 •CRESTRON GREEN LIGHT Power Switching Installation Guide – DOC. 6672B

CRESTRON GREEN LIGHT™ Power Switching

Connector Wiring

RED

WHITE

BLUE

BLACK

NET:

TO CONTROL SYSTEM AND

OTHER CRESNET DEVICES

POWER:

24 VDC JUMPERED FROM NET

PORT or EXTERNAL SUPPLY.

PROVIDES CRESNET POWER

TO THE MODULES

OVERRIDE:

FROM DEVICE PROVIDING

CONTACT CLOSURE & TO

OTHER DEVICES RECEIVING

OVERRIDE SIGNAL

NET Port Wiring

When wiring the supplied NET connectors for connection to a Crestron control system or other device on the

Cresnet network, use Crestron certified wire such as CRESNET-NP or CRESNET-P.

To ensure optimum performance over the full range of your installation topology, use Crestron certified wire.

Failure to do so may incur additional charges if support is required to identify performance deficiencies because

of using improper wire.

When daisy-chaining connections between NET ports, strip the ends of the wires carefully to avoid nicking the

conductors. Twist together the ends of the wires that share a pin on the network connector, insert the connection

into the Cresnet connector, and tighten the retaining screw. Repeat the procedure for the other three conductors.

POWER Port Wiring

Low voltage (24 VDC) power must be supplied to the modules either internally via devices connected to the

NET port or externally via a Cresnet power supply connected to the POWER port.

To power the modules internally from line power, install a jumper from the INT pin on the supplied POWER

connector to the EXT pin on the POWER connector as shown in the following diagram.

Providing Cresnet Power Internally

When a lighting module is powered from line power, the module’s PWR LED will illuminate.

Installation Guide – DOC. 6672B CRESTRON GREEN LIGHT Power Switching •9

Power Switching CRESTRON GREEN LIGHT™

To power the modules externally from a Cresnet 24 VDC power supply, connect the external power supply to

the EXT and Gpins on the POWER supplied connector as shown in the following diagram.

Providing Cresnet Power Externally

CRESTRON 24 VDC

POWER SUPPLY

G 24

When properly connected and receiving 24 VDC power externally, the green LED next to the MODULES port

will light.

When a lighting module is powered from a Cresnet power supply in the absence of line power, the module’s

PWR LED will flash.

OVERRIDE Port Wiring

Low-voltage input devices such as the Crestron GLS-PLS-120/277 phase-loss sensor or any device that

provides a dry contact closure can be connected to the supplied OVERRIDE connector on the bottom of the

cabinet.

10 •CRESTRON GREEN LIGHT Power Switching Installation Guide – DOC. 6672B

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Fuente de alimentación de Crestron

Crestron

Crestron CSA-PWS10S-HUB Manual de usuario

Crestron

Crestron FT2A-UTK-PWS Manual de usuario

Crestron

Crestron DM-PSU-8 Manual de usuario

Crestron

Crestron CSA-PWS10S-HUB-ENET Manual de usuario

Crestron

Crestron DigitalMedia DM-MDA-64-PWS Manual de usuario

Crestron

Crestron C2N-SPWS300 Manual de usuario

Crestron

Crestron DM-PSU-ULTRA-MIDSPAN Manual de usuario

Crestron

Crestron CSA-PWS300-CAEN Manual de usuario

Crestron

Crestron CNPWS-75 Manual de usuario

Crestron

Crestron DM-PSU-8-PLUS Dibujo dimensional

Crestron

Crestron GLA-PWS50 Manual de usuario

Crestron

Crestron CSA-PWS10S-HUB Manual de usuario

Crestron

Crestron C2N-SPWS300 Manual de usuario

Crestron

Crestron Green Light DIN-PWS50 Cómo utilizar

Crestron

Crestron ST-PC Manual de usuario

Crestron

Crestron DM-PSUA-PWS Manual de usuario

Crestron

Crestron CSA-PWS225 Cómo utilizar

Crestron

Crestron GLA-PWSI50 Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Agilent Technologies

Agilent Technologies 6631B Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

HP 6200B Manual de servicio

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario