Crestron DM-NAX-16AIN Manual de usuario

DM-NAX-16AIN QuickStart

DM NAX™ Audio-over-IP Network Encoder with 16 Stereo Inputs

The Crestron® DM NAX™ Audio-over-IP (AoIP) encoder (DM-NAX-16AIN) provides 16 local stereo audio inputs to a DM NAX Crestron multiroom audio

distribution network.

Front Panel

In the Box

1 DM-NAX-16AIN

Additional Items

2 Bracket, Rack Ear, 1U (2032122)

4 Connector, 5-Pin (2003577)

1 Power Cord, 6 ft 7 in. (2 m) (2001134)

Install the Device

Refer to the Safety Instructions (Doc. 6607) prior to installation.

The device can be placed on a flat surface or installed in a rack.

Place on a Flat Surface

Place the device on a flat surface such as a table.

Install in a Rack

This device occupies 1U of rack space.

1. Use a Phillips screwdriver (not included) to remove the three screws

from each side of the device as shown in the illustration.

2. Use the screwdriver and the six screws (removed earlier) to attach

the included rack ears to the device.

3. Mount the device into the rack using four rack mounting screws (not

included).

DM-NAX-16AIN QuickStart

DM NAX™ Audio-over-IP Network Encoder with 16 Stereo Inputs

Rack Mounting Safety Precautions

Elevated Operating Ambient Temperature: If installed in a closed or

multi-unit rack assembly, the operating ambient temperature of the

rack environment may be greater than the room ambient temperature.

Therefore, consideration should be given to installing the equipment in

an environment compatible with the maximum ambient temperature

(Tma) specified by the manufacturer.

Reduced Airflow: Installation of the equipment in a rack should be such

that the amount of airflow required for safe operation of the equipment

is not compromised.

Mechanical Loading: Mounting of the equipment in the rack should be

such that a hazardous condition is not achieved due to uneven

mechanical loading.

Circuit Overloading: Consideration should be given to the connection of

the equipment to the supply circuit and the effect that overloading of

the circuits might have on overcurrent protection and supply wiring.

Appropriate consideration of equipment nameplate ratings should be

used when addressing this concern.

Reliable Earthing: Reliable earthing of rack-mounted equipment should

be maintained. Particular attention should be given to supply

connections other than direct connections to the branch circuit (e.g., use

of power strips).

Connect the Device

Make the necessary connections as called out in the following

illustration. Connect power last.

CAUTIONS:

lKeep the device unplugged until all of the input wiring is complete.

lCheck the connections for shorts and frayed wiring at all the input

connectors.

NOTES:

lEnsure that the unit is properly grounded by connecting the chassis

ground lug to an earth ground (building steel).

lTo prevent overheating, do not operate this product in an area that

exceeds the environmental temperature range of 32° to 104°F (0° to

40°C).

lDo not bundle power cords together with connection cables. Doing

so can result in noise.

DM-NAX-16AIN QuickStart

DM NAX™ Audio-over-IP Network Encoder with 16 Stereo Inputs

DM-NAX-16AIN QuickStart

DM NAX™ Audio-over-IP Network Encoder with 16 Stereo Inputs

Rear Panel

Digital Inputs

Refer to the following illustration when connecting digital audio sources.

NOTE: Only 2-channel PCM digital audio is supported at the digital

inputs.

Analog Inputs

Refer to the following illustration when connecting analog audio sources.

Balanced/Unbalanced Audio Input

Refer to the following table and illustration for analog audio input pin

assignments and connection information.

Signal Name Balanced Audio Input Unbalanced Audio Input

+ L+ L+

- L− L Shield

G Shield/ground G, L Shield, and R Shield

+ R+ R+

- R- R Shield

DM-NAX-16AIN QuickStart

DM NAX™ Audio-over-IP Network Encoder with 16 Stereo Inputs

Reset the Device

A network reset or factory restore may be performed when

troubleshooting.

Network Reset

1. Ensure the device is powered on.

2. Press and hold the SETUP button for up to 15 seconds until the

SETUP LED flashes red.

The device will reboot, and the default network settings will be reset,

such as default Hostname, DHCP enabled, no static IP.

Factory Restore

1. Turn off the device by disconnecting the power cable from the device.

2. Press and hold the SETUP button and then reconnect the power

cable while still holding the SETUP button. Continue holding the

SETUP button for up to 30 seconds until the SETUP LED flashes.

The device will reboot, and all the factory default settings will be

restored, such as Zone settings, names, multicast addressing, etc.

CAUTION: Performing a factory restore will clear all settings from the

device configuration.

Observe the LED Indicators

Refer to the following table for information about the LED indicators on

the device.

LED Indicator Color Meaning

PWR Amber Power is being applied to the device.

Thedevice is booting.

White Device is powered on with audio

passing.

Red Device is in standby mode.

LAN White The device is powered on and has a

valid IP address.

Off Device is not connected to a network

or the IP address is invalid.

NAX White AoIP is ready to pass and the unit's

PTP clock is synced.

Off No AoIP is passing to or from and/or

PTP is not synced.

SOURCE 1-16 White Signal is detected on the specified

input/source.

Red There is clipping on an analog input or

bitstream audio detected on a digital

input.

Off There is no signal detected on the

specified input/source.

SETUP Solid Red The SETUP button is pressed.

Blinking Red A network reset or factory restore has

been initiated via the adjacent SETUP

button.

DM-NAX-16AIN QuickStart

DM NAX™ Audio-over-IP Network Encoder with 16 Stereo Inputs

Visit the Product Page

Scan the QR code to visit the product page.

www.crestron.com/model/6510879

Additional Information

Original Instructions

The U.S. English version of this document is the original instructions.

All other languages are a translation of the original instructions.

Regulatory Model: M201845005

Crestron product development software is licensed to Crestron dealers and Crestron

Service Providers (CSPs) under a limited nonexclusive, nontransferable Software

Development Tools License Agreement. Crestron product operating system software is

licensed to Crestron dealers, CSPs, and end-users under a separate End-User License

Agreement. Both of these Agreements can be found on the Crestron website at

www.crestron.com/legal/software_license_agreement.

The product warranty can be found at www.crestron.com/warranty.

The specific patents that cover Crestron products are listed at

www.crestron.com/legal/patents.

Certain Crestron products contain open source software. For specific information, visit

www.crestron.com/opensource.

Crestron, the Crestron logo, and DM NAX are either trademarks or registered

trademarks of Crestron Electronics, Inc. in the United States and/or other countries.

TOSLINK is either a trademark or a registered trademark of Toshiba Electronics Devices

& Storage Corporation in the United States and/or other countries. Other trademarks,

registered trademarks, and trade names may be used in this document to refer to either

the entities claiming the marks and names or their products. Crestron disclaims any

proprietary interest in the marks and names of others. Crestron is not responsible for

errors in typography or photography.

Doc. 9059B

10/28/21

DM-NAX-16AIN QuickStart

DM NAX™ Audio-over-IP Network Encoder with 16 Stereo Inputs

Tabla de contenidos

Otros manuales de Convertidor de medios de Crestron

Crestron

Crestron HD-SCALER-HD-E Manual del propietario

Crestron

Crestron CNRJ11 Manual de usuario

Crestron

Crestron ZUM ZUMLINK-SPLTR-RJ45 Manual de usuario

Crestron

Crestron DM-NVX-E30 Manual de usuario

Crestron

Crestron DM-NVX-E20-2G Manual de usuario

Crestron

Crestron HD-WP-4K-401-C Manual del propietario

Crestron

Crestron DM-NVX-363 Manual de usuario

Crestron

Crestron DM-NVX-360 Manual de usuario

Crestron

Crestron HD-CONV-USB-200 Manual de usuario

Crestron

Crestron UC-BRKT-200-S-Z-ASSY Manual de usuario

Crestron

Crestron HD-SCALER Cómo utilizar

Crestron

Crestron DM-NVX-E30 Manual de usuario

Crestron

Crestron DigitalMedia DM-NVX-350 Manual de usuario

Crestron

Crestron RCA Analog Video Input Card w/Analog Audio... Manual de usuario

Crestron

Crestron DM-DA4-4K-C Dibujo dimensional

Crestron

Crestron HD-SCALER Cómo utilizar

Crestron

Crestron UC-BRKT-200-S-T-ASSY Manual de usuario

Crestron

Crestron DigitalMedia DM-NVX-351 Manual de usuario

Crestron

Crestron DVPHD Manual de usuario

Crestron

Crestron HD-PS401 Manual de usuario

Crestron

Crestron DigitalMedia NVX Series Guía

Crestron

Crestron DM-NVX-352 Manual de usuario

Crestron

Crestron DM-NVX-E30 Manual de usuario

Crestron

Crestron HD-CONV-USB-250 Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario