CI372X01R1
Page 2 of 3
30 LED LUMINAIRE
Switch
Position
1050mA Max 700mA Max 525mA Max
Drive
Current
Power
Multiplier
Lumen
Multiplier
Drive
Current
Power
Multiplier
Lumen
Multiplier
Drive
Current
Power
Multiplier
Lumen
Multiplier
1525 0.44 0.59 350 0.49 0.55 175 0.36 0.54
2 600 0.51 0.66 425 0.60 0.66 225 0.45 0.60
3675 0.59 0.74 475 0.67 0.72 275 0.55 0.70
4750 0.65 0.79 525 0.73 0.79 325 0.64 0.76
5 825 0.72 0.85 550 0.78 0.82 350 0.67 0.82
6 900 0.78 0.90 575 0.81 0.84 375 0.72 0.88
7950 0.83 0.93 625 0.88 0.91 425 0.83 0.92
8 1000 0.87 0.97 650 0.92 0.92 475 0.92 0.96
9 1050 1.00 1.00 700 1.00 1.00 525 1.00 1.00
60 LED LUMINAIRE
Switch
Position
900mA Max 700mA Max 525mA Max 350mA Max
Drive
Current
Power
Multiplier
Lumen
Multiplier
Drive
Current
Power
Multiplier
Lumen
Multiplier
Drive
Current
Power
Multiplier
Lumen
Multiplier
Drive
Current
Power
Multiplier
Lumen
Multiplier
1350 0.40 0.46 350 0.49 0.55 175 0.36 0.39 175 0.49 0.55
2 425 0.52 0.54 425 0.60 0.66 225 0.45 0.51 213 0.60 0.66
3475 0.53 0.60 475 0.67 0.72 275 0.55 0.63 238 0.67 0.72
4525 0.58 0.65 525 0.73 0.79 325 0.64 0.70 263 0.73 0.79
5 600 0.67 0.72 550 0.78 0.82 350 0.67 0.76 275 0.78 0.82
6675 0.75 0.79 575 0.81 0.84 375 0.72 0.81 288 0.81 0.84
7750 0.83 0.87 625 0.88 0.91 425 0.83 0.87 313 0.88 0.91
8 825 0.92 0.92 650 0.92 0.92 475 0.92 0.94 325 0.92 0.92
9 900 1.00 1.00 700 1.00 1.00 525 1.00 1.00 350 1.00 1.00
90 LED LUMINAIRE
Switch
Position
700mA Max 525mA Max 350mA Max
Drive
Current
Power
Multiplier
Lumen
Multiplier
Drive
Current
Power
Multiplier
Lumen
Multiplier
Drive
Current
Power
Multiplier
Lumen
Multiplier
1350 0.49 0.55 175 0.36 0.39 175 0.49 0.55
2 425 0.60 0.66 225 0.45 0.51 213 0.60 0.66
3475 0.67 0.72 275 0.55 0.63 238 0.67 0.72
4525 0.73 0.79 325 0.64 0.70 263 0.73 0.79
5 550 0.78 0.82 350 0.67 0.76 275 0.78 0.82
6575 0.81 0.84 375 0.72 0.81 288 0.81 0.84
7 625 0.88 0.91 425 0.83 0.87 313 0.88 0.91
8 650 0.92 0.92 475 0.92 0.94 325 0.92 0.92
9700 1.00 1.00 525 1.00 1.00 350 1.00 1.00
FIELD ADJUSTABLE DIMMING
STEP 1:
This luminaire is provided
with field adjustable dimming.
Luminaires leave the factory
adjusted to the maximum
setting which is Position 9 as
shown in Figure 6.
STEP 2:
Locate the luminaires electrical
label and verify the luminaires
LED count and the maximum
current available.
STEP 3:
The Dimming module is located
inside the luminaire. Open
the sensor door by loosening
the (4) self retained screws
and carefully lower the door.
See Figure 3 on page 1.
STEP 4:
Establish the desired drive
current on the following tables
and turn the switch to the
correlating position on the
Dimming Control Module.
STEP 5:
Adjust the Dimming Module to
the selected position, replace
the door ensuring no wires are
pinched. Tighten the screws
that were loosened in Step 3.
F6
