Creality CV-01 PRO Manual de usuario
Laser Engraving Machine
CV-01 PRO
User Manual • Uživatelský manuál •
Užívateľský manuál • Használati utasítás •
Benutzerhandbuch
2
English
3 –15
Čeština
16 –27
Slovenčina
28 –40
Magyar
41 –52
Deutsch
53 –65
3
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully
before first use and keep this user manual for future reference. Pay particular attention
to the safety instructions. If you have any questions or comments about the device,
please contact the customer line.
www.alza.co.uk/kontakt
✆+44 (0)203 514 4411
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz
Firmware Upgrade
Please login the official website https://www.creality.com/download, switch the language
and select the relevant printer and model and download the required firmware, you can
use it after the installation is finished.
Notes
•For the purpose of engraving or cutting with a laser engraving machine, allow the
workpiece to be exposed to the high-density laser beam emitted by the laser
engraving machine. The workpiece may be subject to gasification without
combustion as it is pretty hot on the surface. On the other hand, most
workpieces are essentially combustible, which may be ignited, leading to open
fire and consequently to the machine breakdown and environmental
contamination.
•It is prohibited to store the machine in areas close to combustible and explosive
substances, volatile solvents or source of heat. Instead, store it in a well-
ventilated, cool and dust-free place.
•Make sure that only the specific attached power cord rather than other similar
power cords are used during installation.
•Ensure to run the laser at 0°C-35°C. Operation at sub-zero temperature is
prohibited. It is prohibited to run the machine under wet environment or in
thunderstorm weather
•If the user needs to strengthen the protection during the use or maintenance,
you shall wear a protective suit with a compliant and laser protective effect.
•Switch off the machine if it is offline for an extended period of time, and unplug
the power cord.
•It is prohibited to come in contact with electronic areas with hands or other tools
when the machine is connected to power supply
•Touching any moving parts and laser module while the machine is running is
prohibited.
4
•Wear goggles to prevent vision damage arising from exposure to the laser spot
during laser engraving operation,
•It is advisable to run the machine under well ventilated condition as laser
engraving may generate small amount of fume or gas;
•Children under 10 years old are not allowed to run the machine without adult
presence, which otherwise may lead to personal injury
•Put in place fire extinguishers in case of use, which shall be regularly checked. It
is prohibited to keep the machine unattended while it is running
•Users should comply with the laws and regulations of the corresponding
countries and regions where the equipment is located (used), abide by
professional ethics, pay attention to safety obligations, and strictly prohibit the
use of our products or equipment for any illegal purposes. Creality will not be
responsible for any violators' legal liability under any circumstance.
Introduction
1) Gradienter
5) Focusing bar
2) X-axis assembly
6) Control Box assembly
3) Y-axis assembly
7) Laser module
4) Microswitch
5
Equipment Parameters
Model
CV-01 Pro
Machine size
480mm*315mm*145mm
Net weight
1.8KG
Gross weight
2.95 KG
Operation system
Windows XP and above systems
Power supply
DC 12.0V 3.0A
Range of operating temperature
0°C-35°C
Safety certification
FDA, CE, ROHS, FCC
Engraving Size
170mm*200mm
Laser source
Semiconductor laser unit
Laser wave length
450±5nm
Laser power
1.6W
Safety class
Class I - FDA classification standard
Laser engraving software
CrealityLaser, LaserGRBL, LightBurn
Format of supporting files of laser
engraving software
Jpeg, jpg, png, bmp, svg, dxf
Type of support materials
Cardboard, wood, bamboo, rubber, leather,
fabric, acrylic, plastic, etc.
Package Content
X-axis assembly, Y-axis
assembly x1
Power adaptor
x1
Linden
plywood x2
Color card
paper x7
Socket head wrench
( M1.5/M2/M2.5/M3 )
x4
Kraft paper x2
Silicone pad x2
Goggles x1
Hand screw with
cylindrical head x1
Knurled nut
with collar x4
Quick
installation
guide x1
Color asphalt
felt paper x7
Open
spanner x1
Silica gel anti collision particles
x2
TF card & card
reader x1
6
Assembled laser engraving machine
1. Assemble the X-axis assembly and the Y-axis assembly. Take out the X-axis assembly
and the Y-axis assembly from packaging box. Horizontally place the X-axis assembly
above the Y-axis assembly, and align the tapped holes to the projected screws
underneath. Then lower it horizontally onto the Y-axis assembly. Finally, put on 4
knurled nuts with collar and tighten them clockwise.
X-axis assembly, Y-axis
assembly x1
Knurled nut
with collar x4
7
2. Assemble the Y-axis stepper motor cable (Ensure assembling when power is off)
Insert the Y-axis stepper motor wire into the wiring port in the direction as shown in
the above figure. The wiring port has an anti-reverse connection design, please pay
attention to distinguish the direction of the interface.
3. Make sure that the machine is in a horizontal stat.
Observe the level on the X-axis assembly to make sure that the machine is horizontal. If
not, please check the desktop whether it is flat. Then loosen the knurled nut with collar
to readjust the position of the X-axis assembly and the Y-axis assembly.
8
Software installation and usage
The TF card included with the package contains software installation package required
by laser engraving. Please insert the TF card into card reader, connect it to the computer
to get the installation file. Or download from:
https://www.cxsw3d.com/ziliaoxiazai46.html
Software Intro
Open the CrealityLaser software. Interface is shown as the figure below.
1. Menu: The menu includes operations such as opening and closing of image files,
switching of views, obtaining help documents and language settings of the software,
etc.
2. Toolbar: The toolbar contains common operations such as adding files, text, and QR
codes
3. Preview Area: The preview area is the area used to preview the engraved graphics. It
corresponds to the engraving area of the machine. The image placed in the preview area
will be engraved at the corresponding position
4. Setting: Switching the model and language settings.
5. Console: Available elect the corresponding machine model. After adding the file, you
can perform various parameter settings and preview, generate and export gcode
operations for the files to be processed.
1. Double-click to
open the software
package and click
"Run".
3. Wait for software
installation completion
and click "Finish".
2. “Install”。Confirm installation
location. You can click "Browse..."
to select a "non-C drive" installation
location such as D drive, and then
click "Install".
9
Operation mode
1. Put the engraving material in processing area, adjust the manual nut on the right side
of the laser head, and turn the fixed focus bar counter clockwise to make it contact with
the surface of the processed material when it is naturally vertical downward. Then
tighten the manual nut and turn the fixed focus bar clockwise until it is attracted by the
magnet.
10
2. Double-click to open the "CrealityLaser" software, click "Setup" button in the upper
right, select machine (CV-01 Pro), and click “Return"
3. Click "Add File" in the toolbar to find the image file that needs to be engraved. Open
and import the image into CrealityLaser software; Adjust the size, angle, position, and
flip mode of the image file in the console, and set the image processing mode, density,
material, working parameters, etc.
Preview the processing effect of the image and generate G-code. You can see the
estimated working time at the bottom right of the interface:
Tabla de contenidos
Idiomas:
Otros manuales de Impresora de Creality
