Crane DN5800 Instrucciones de funcionamiento e instalación

M132.4 Page 1of 3June 25, 2019

SERVICE INFORMATION

104883 (M132.4)

MODELS AFFECTED: All BevMax 4/3/2 Classic Model Venders.

MODEL NUMBERS: DN5800/3800 – BevMax 4/3/2 Venders

Revised: 6/25/19

RE: Crane Merchandising Systems DN5800/3800-4/3/2 Validator Guard Assembly.

Reason: To provide installation instructions when installing the Validator Guard Assembly. If you have

any issues please contact your Crane Merchandising Systems Representative or the Technical Service

Department at 803-266-5001.

Order: 1 – 111250 (previous # 65701440) BevMax 4/3/2 Validator Guard Kit

Kit Contents:

1 – 104705 (previous # CR0013381) Assembly, Validator Guard BevMax 4/3/2

5 – 100267 (previous # 80030423) Screws, Phil Pan Sems #8-18X1/2”

1 – 104883 M132.x Installation Instructions

Figure 1

Note access hole for the

screw to the vertical

lamp assy.

M132.4 Page 2of 3June 25, 2019

SERVICE INFORMATION

Installation:

1. Unplug the vender.

2. A. If the Validator Guard 104705 (previous # CR0013381) Assembly did not arrive assembled,

assemble the parts as shown in Figure1. Do not tighten the Hex Nuts at this time.

B. If the Validator Guard Assembly arrived assembled, be sure the two Hex Nuts are not tight at

this time.

3. Orient the Validator Guard Assembly as shown in Figure 1.

4. Position the Validator Guard Assembly in position in the Vender Service Area so the left flange

points upward and the bottom of the plate rests just above the top edge of the Discharge Frame.

Figure 2

5. Check no wires are pinched, cut, or damaged in any way.

Figure 3

Note positioning of the

access hole for the

screw to the vertical

lamp assy.

M132.4 Page 3of 3June 25, 2019

SERVICE INFORMATION

6. Ensure the left & right front edges of the Validator Guard Assembly are even with the front edges

of the cabinet. See Figures 2 & 3.

7. Secure the Validator Guard Assembly in position with 5 Phil Pan Sems self-drilling Screws 100267

(previous # 80030423).

8. Tighten the 2 Hex Nuts on the Validator Guard Assembly. See Figure 4.

Figure 4

9. Close Service Door and confirm there is no interference with any parts on the Service Door or in

the Service Area of the Vender.

Figure 5

10. Plug in vender and test for proper operation.

Hex Nut

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Comerciante de Crane

Crane

Crane BevMax 4 Manual de usuario

Crane

Crane Coca-Cola BevMAX Refresh Instrucciones de funcionamiento

Crane

Crane 787E Manual

Crane

Crane Snack Center 1 Manual de usuario

Crane

Crane Dixie Narco Glassfront BevMax 3 Manual de usuario

Crane

Crane BevMax 3 Instrucciones de funcionamiento e instalación

Crane

Crane BEVMAX 6 Manual de usuario

Crane

Crane BevMAX Refresh 6 Media Manual de usuario

Manuales populares de Comerciante de otras marcas

FRIGOGLASS

FRIGOGLASS Flex 20 HC Manual de usuario

Hussmann

Hussmann ENTYCE TY3 Manual de usuario

EPTA

EPTA COSTAN RHINO MULTI Manual de usuario

Hussmann

Hussmann CRFD Instrucciones de funcionamiento

CASCO

CASCO Nano Cube Manual de usuario

Hussmann

Hussmann WDCHI Manual de usuario

True

True GDIM-26 Manual de usuario

Structural Concepts

Structural Concepts Oasis Mobile Series Instrucciones de instalación

Hussmann

Hussmann Q2-SS Instrucciones de funcionamiento originales

Haussmann

Haussmann RL Manual de usuario

Howard McCray

Howard McCray R-CDS32E-4 Manual de usuario

Hussmann

Hussmann microSC SHM-A Series Manual de usuario

Hussmann

Hussmann APT0500 Manual de usuario

EPTA

EPTA iarp Cool Emotions Delight Lite Manual de usuario

VALERA

VALERA BC 85 Manual de usuario

HL Display

HL Display 3eBin Manual de usuario

Hussmann

Hussmann Q1-SS Manual de instrucciones

Hussmann

Hussmann impact Excel C2X-XLEP Manual de instrucciones