Craig CTFT716n Manual de usuario
7 INCH PORTABLE DVD PLAYER
with Swivel Screen Display
7 INCH PORTABLE DVD PLAYER
with Swivel Screen Display
Model: CTFT716n
PLEASE READ BEFORE OPERATING THIS EQUIPMENT.
Owner's Manual
Size: 148.5(W) x 210(H)mm (A5)
CAUTION:
THIS DIGITAL VIDEO DISC PLAYER EMPLOYS A
LASER SYSTEM.
TO ENSURE PROPER USE OF THIS PRODUCT.
PLEASE READ THIS OWNER`S MANUAL CAREFULLY
AND RETAIN FOR FUTURE REFERENCE. SHOULD
THE UNIT REQUIRE MAINTENANCE, CONT ACT AN
AUTHORIZED SERVICE LOCATION-SEE SERVICE
PROCEDURE.
USE CONTROLS, ADJUSTMENTS OR THE
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
TO PREVENT DIRECT EXPOSURE TO LASER BEAM,
DO NOT TRY TO OPEN THE ENCLOSURE. VISIBLE
LASER RADIATION MAY BE PRESENT WHEN THE
ENCLOSURE IS OPENED. DO NOT STARE INTO BEAM.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, AND ANNOYING INTERFERENCE, USE THE
RECOMMENDED ACCESSORIES ONLY.
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to alert
the user to the presence of uninsulated
dangerous voltage within the product`s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance(servicing) instructions in the
literature accompanying the appliance.
DANGER:
Invisible and hazardous laser radiation when
open and interlock failed or defeated. Avoid
direct exposure to beam.
FCC NOTICE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not Installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
FCC WARNING:
To assure continued compliance, follow the attached
installation instructions and use only shielded cables
when connecting to other devices. Modifications not
authorized by the manufacturer may void user`s authority
to operate this device.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
-1-
IMPORTANT SAFETY INSTRUCTION
Before using the unit, be sure to read all operating instructions carefully. Please note that these
are general precautions and may not pertain to your unit.
1) Read these instructions.
All the safety and operating instructions should be read before the product is operated.
2) Keep these instructions.
The safety and operating instructions should be retained for future reference.
3) Heed all warnings.
All warnings on the product and in the operating instructions should be adhered to.
4) Follow all instructions.
All operating and use instructions should be followed.
5) Do not use this apparatus near water.
Do not use this product near water and moisture, for example: near a bathtub, washbowl, kitchen
sink or laundry tub; in a wet basement; or near a swimming pool.
6) Clean only with dry cloth.
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a dry cloth for cleaning.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
Slots and openings in the cabinet and in the back or bottom are provided for ventilation, to ensure
reliable operation of the product and to protect it from overheating. These openings must not be
blocked or covered. The openings should never be blocked by placing the product on a bed, sofa,
rug or other similar surface. This product should never be placed near or over a radiator or heat
source. This product should not be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer's instructions have been adhered to.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10)Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11)Only use attachments/accessories specified by the manufacturer.
12)Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
An appliance and cart combination should be moved with care.
Quick stop, excessive force and uneven surfaces may cause the
appliance and cart combination to overturn.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
To protect your product from a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This
will prevent damage to the product due to lightning and power-line surges.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain
or moisture does not operate normally, or has been dropped.
15) Power source
This product should be operated only from the type of power source indicated on the marking label.
If you are not sure of the type of power supply to your home, consult your appliance dealer or local
power company. For products intended to operate from battery power, or other source, refer to the
operation instructions.
16) Power lines
An outside antenna system should not be located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such power lines or circuits. When
installing an outside antenna system, extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be fatal.
-2-
IMPORTANT SAFETY INSTRUCTION
For example, this unit may not have the capability to be connected to an outdoor antenna.
17) Overloading
Do not overload wall outlets and extension cords as this can result in a risk of fire or electric
shock.
18) Object and liquid entry
Never push objects of any kind into the product through openings as they may touch dangerous
voltage points or short out parts that could result in fire or electric shock.Never spill or spray any
type of liquid on the product.
19) Outdoor antenna grounding
If an outside antenna is connected to the product,be sure the antenna system is grounded so as to
Provide some protection against voltage surges and built up static charges.Section 810 of the
National Electric Code ANSI/NFPA 70 provides information with respect to proper to grounding
of the mast and supporting structure,grounding of the lead-in wire to an antenna discharge product,
size of grounding conductors,location of antenna-discharge product,connection to grounding
electrodes and requirements for the grounding electrodes.
20)Service
Do not attempt to service this product yourself as opening or removing covers may expose you to
dangerous voltage or other hazards.Refer all servicing to qualified service personnel.
21)Replacement parts
When replacement parts are required,be sure the service technician uses replacement parts
specified by the manufacturer or those that have the same characteristics as the original parts.
Unauthorized substitutions may result in fire or electric shock or other hazards.
22)Safety check
Upon completion of any service or repairs to this product,ask the service technician to perform
safety checks to determine that the product is in proper operational condition.
23) Wall or ceiling mounting
The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
24)Damage requiring service
Unplug this product from the wall outlet and refer service to qualified service personnel under the
following conditions.
a)When the power-supply cord or plug is damaged.
b)If liquid has been spilled or objects have fallen into the product.
c)If the product has been exposed to rain or water.
d)If the product does not operate normally by following the operating instructions.Adjust only
those controls that are covered by the operating instructions,as an adjustment of other
controls may result in damage and will and require extensive work by a qualified technician
to restore in the product to its normal operation.
e)If the product has been dropped or the cabinet has been damaged.
f)When the product exhibits a distinct change in performance-this indicates a need for service.
25)Note to CATV system installer
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the
NEC that provides guidelines for proper grounding and,in particular,specifies that the cable
ground shall be connected to the grounding system of the building,as close to the point of cable
entry as practical.
NOTE: Refer all servicing to qualified service personnel Servicing is required when
the unit has been damaged in any way such as the following: the power-supply cord
or plug has been damaged, liquid has been spilled into unit, the unit has been
exposed to rain or moisture, the unit has been dropped or the unit does not operate normally.
-3-
IMPORTANT SAFETY INSTRUCTION
When shipping the unit, always use the
original shipping carton and packing materials.
For maximum protection, repack the unit as it
was originally packed at the factory.
Do not use volatile liquids, such as insect spray,
near the unit. Do not leave rubber
or plastic products in contact with the unit
for a long time. They will leave marks on the finish.
The top and rear panels of the unit
may become warm after a long period of use.
This is normal and not a malfunction.
When the DVD player is not in use, be sure
to remove the disc and turn off the power.
When you place this unit near a TV, radio
or VCR, the playback picture may become poor
and the sound may be distorted. In this case, move
the unit away from the TV, radio or VCR.
For stubborn dirt, soak the cloth in a weak
detergent solution, wring well and wipe. Use a
dry cloth to wipe it dry. Do not use any type
of solvent, such as thinner and benzene, as they
may damage the surface of the unit.
If you use a chemical-saturated cloth to clean
the unit, follow that product's instructions.
NOTES ON HANDLING:
NOTES ON LOCATING THE DVD PLAYER:
NOTES ON CLEANING:
Use a soft, dry cloth for cleaning
Warning: Cleaning and adjustment of lenses and /or
other components of playback mechanism should be
performed by a qualified service technician.
Moisture condensation occurs, for example, when you
pour a cold drink into a glass on a warm day. Drops of
water form on the outside of the glass. In the same way,
moisture may condense on the optical pick-up lens
inside this unit, one of the most crucial internal parts
of the DVD player.
Moisture condensation occurs during the
following cases:
When you bring the DVD player directly from a cold
place to a warm place.
When you use the DVD player in a room where you
just turned on the heater, or a place where the cold
wind from the air conditioner directly hits the unit.
ln summer, when you use the DVD player in a hot and
humid place just after you moved the unit from an air
conditioned room.
When you use the DVD player in a humid place.
Do not use the DVD player when moisture
condensation may occur.
lf you use the DVD player in such a situation,
it may damage discs and internal parts. Remove
the disc, connect the AC Cord to wall outlet，turn on
the DVD player and leave it ON for two or three hours.
After two or three hours,the DVD player will have
warmed up and evaporated any moisture.
.
Please read the following carefully.
-4-
IMPORTANT SAFETY INSTRUCTIONS
NOTES ON MOISTURE CONDENSATION:
Moisture condensation damages the DVD player
1
ABOUT DISCS
The region number for this DVD Player is:
See the following page for information regarding region numbers.
PLAYABLE DISCS:
The following discs can be played back on this DVD player:
DISC TYPES:
DVD
Data on most DVDs is divided into sections called titles
and then into subsections called chapters, each of which
is given a title or chapter number. Some features of this
DVD player will not operate with some DVD discs as they
are preset. If a function you selected does not run as
desired , refer to the manual accompanying the DVD disc.
AUDIO CD
Data on an audio CD is divided into sections called tracks ,
each of which is given a track number.
IMPORTANT:
It is important that you read the manual that accompanies the DVD disc , as there are
features that are on the DVD player that cannot be used with certain DVDs .
There are also extra features on the DVD disc that are different for each DVD disc ,
so they are not explained in this owner's manual.
This player conforms to the NTSC and PAL color systems . However , if you are in
the USA , Canada or Mexico,leave this setting on NTSC . If incorrectly set to PAL ,the
TV picture may roll vertically. In this case , set the TV system to NTSC .
ABOUT DISCS
Notes on Copyright:
It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public and rent copyrighted
material without permission. DVD video discs are copy protected, and any recordings made from these
discs will be distorted. This product incorporates copyright protection technology that is protected by
method claims of certain U.S. Patents and other intellectual property rights owned by Macrovision
Macrovision Corporation, and is intended for home and other limited viewing uses only, unless
otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Region Management Information:
This DVD Player is designed and manufactured to respond to the Region Management Information that
is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to
the Region number of this DVD player, this DVD player cannot play that disc. You may not be able to
play back some DVD video discs on this player if they were purchased from outside your geographic
area or made for business purposes. When you try to play back an unauthorized disc, Wrong Region
appears on the TV screen.
-5-
LCD ON /O FF OSD MUTE
SETU P TITLE MENU
VOL- V OL + REPEAT
AUDI O
LOCATION OF CONTROLS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
LCD ON/OFF: Press to turn on or turn off
MUTE:
SETUP: Press to enter DVD system setup menu and press again to exit.
REPEAT:
Press to decrease volume level.
Press to stop.
OSD :
MENU: Press to return to disc's menu
TITLE:
VOL+ : Press to increase the volume level.
: Press to confirm the selection ( settings ).
Press to turn off sound. Press again to resume.
OPEN:
VOL-:
AUDIO:
ENTER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Ŷ
ŹOO
Ŷ
ŹOO
-6-
(Saving the battery power while music playback)
the screen.
(On Screen Display) Press to display the information.
page. (Function depends on the disc recording).
Direction Buttons: Press to select the desired settings within setting menu.
Press to start playback or pause.
Slide to right to open the disc door.
Press repeatedly to select and set the repeat modes.
Press repeatedly to select the audio channels.(Function depends on the disc recording).
Press to return to disc's title page. (Function depends on the disc recording).
LOCATION OF CONTROLS
Right Side of the Player
Power On/Off Switch
DC IN Jack
Audio/Video output Jack
Coaxial digital audio output Jack
AV OUT COAXIAL
OFF ON
DC IN 12V
POWER
16 17 18 19 20
16
17
18
19
20
21 22
21 22
Indicators Remote Senor
Front Side of the Player
-7-
Phones Jack
LOCATION OF CONTROLS
REMOTE CONTROL
1
2
3
4
5
6
7
89
10
11 12
13 14
15
POWER
16
17
18
19
20
21
22
23
24
25
26
27
28
1. POWER Button
2. VOLUME +/– Buttons
4. GOTO Button
ŻŻ
7.
ǿŻŻ
6. Button
12.
15. SLOW Button
Button
16. LCD ON/OFF Button
17. Numeric Buttons
18. SETUP Button
19. Button
ǿŻŻ
20. Button
ŻŻ
21. OSD (On Screen Display Button
22. SUBTITLE Button
23. ANGLE Button
24. PROG (Program Button
26. STEP Button
27. ZOOM Button
28. A-B Repeat Button
9.
MENU Button
8.
TITLE Button
10.
AUDIO Button
REPEAT Button
13.
11. (
14.
PBC Button
-8-
OK
25. Button
3. MUTE Button
5. Direction Buttons
( Play/Pause Button
6723 %XWWRQ
ENTER
Ŷ
BATTERY INSTALLATION (REMOTE CONTROL)
directions.)
Remote Control Sensor
the battery compartment as the figure on righ and the
polarity markin
battery door and lift it off.
2.Install two (2) x AAA size batteries ( included ) into
Remarks:
1. When there is an obstacle between the unit and the transmitter, the transmitter may not operation.
2. When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light shines on the remote
control of the unit, the remote operation may be unstable.
POWER
-9-
Otros manuales para CTFT716n
1
Tabla de contenidos
Otros manuales de Reproductor de DVD portátil de Craig
