Craftsman 486.244122 Manual de usuario
Owner's Manual
Model No. 486.244122
48" DOZER BLADE
®
CAUTION:
Before using this product, read
this manual and follow all Safety
Rules and
Operating Instructions.
•Safety
•Assembly
•Operation
•Maintenance
•arts
RINTED IN U.S.A. FORM NO. 49344 (REV. 7/04)
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
www.sears.com/craftsman
IMPORTANT - READ THIS FIRST!!!
For Missing arts or Assembly Questions
lease Call 866-576-8388
Mon.-Fri. 7 am - 5 pm CST.
FAX 217-728-2032 or e-mail [email protected]
Missing parts will be sent U S in 24 hours directly to your home.
2
LIMITED ONE YEAR WARRANTY ON 48" DOZER BLADE
For one year from the date of purchase, when this Dozer Blade is maintained and lubricated according to the
operating and maintenance instructions in the owner's manual, Sears will repair any defect in material or
workmanship free of charge. If this Dozer Blade is used for commercial or rental purposes, this warranty applies for
only 90 days from the date of purchase.
This warranty does not cover repairs necessary because of operator negligence or abuse, including the failure to
maintain the equipment according to instructions contained in the owner's manual.
WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEAREST SEARS SERVICE CENTER/DE ART-
MENT IN THE UNITED STATES.
This warranty applies only while this product is in the United States.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co. D/817 WA. Hoffman Estates, Chicago, IL 60179
Look for this symbol to point out important safety precautions. It mean--Attention!!
Become alert!! Your safety is involved.
Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the
equipment. Exercise caution at all times, when using power equipment.
1. Read the tractor and dozer blade owners manuals and know how to operate your tractor before using the tractor with
the dozer blade attachment.
2. Never operate the tractor and dozer blade without wearing proper clothing suited to weather conditions and
operation of controls.
3. Never allow children to operate the tractor and dozer blade. Do not allow adults to operate without proper instructions.
4. Always begin with transmission in first (low) gear and gradually increase speed as required.
SAFETY
CARTON CONTENTS
1. Frame Brackets
2. Lift Assembly
3. Guide Bracket Assembly
4. Spring Assembly (2)
5. Angle Lock Bars (2)
6. Blade ivot Bracket
7. Channel/ ivot late Assembly
8. Grip Assembly
9. Support Bracket
10. Handle Assembly w/Grip
11. Control Cable Assembly
12. Lift ivot late (2)
13. Blade Assembly
arts ackage (See page 3)
3
A
C
M
N
O
P
Q
R
S
T
U
L
K
D E F G H I J
B
WXZ AA
GG
DDCC EE
HH
BB FF
NOT SHOWN FULL SIZE
SHOWN FULL SIZE
II
Y
JJ KK
V
REF. QTY. DESCRIPTION REF. QTY. DESCRIPTION
CONTENTS OF PARTS PACKAGE
A 1 Hex Bolt, 1/2" x 4"
B 2 Hex Bolt, 1/2" x 2-3/4"
C 9 Hex Bolt, 3/8" x 1-1/4"
D 1 Hex Bolt, 3/8" x 1"
E 1 Hex Bolt, 5/16" x 1-1/2"
F 1 Hex Bolt, 1/4" x 1-1/2"
G 1 Hex Bolt, 1/4" x 3/4"
H 2 Hex Bolt, 3/8" x 1" Thread Forming
I 1 Shoulder Bolt, (Special) 3/8" x 5/8"
J 2 Carriage Bolt, 3/8" x 1-1/4"
K 4 Flat Washer, 7/16" Std.
L 1 Flat Washer, 3/8" Std.
M 4 Lock Washer, 3/8"
N 2 Nylock Nut, 1/2"
O 2 Hex Jam Nut, 1/2"
4 Hex Jam Nut, 7/16"
Q 1 Whizlock Nut, 3/8"
R 10 NyLock Nut, 3/8"
S 2 Hex Jam Nut, 3/8"
T 1 Nyock Nut, 5/16"
U 4 Hex Jam Nut, 5/16"
V 3 Nyock Nut, 1/4"
W 2 Keeper late
X 1 Lift Arm Link
Y 1 Stop Angle
Z 1 Cable Mount Bracket
AA 2 Cable End Fitting
BB 1 Handle Guide
CC 4 Clevis in, 3/8" x 3/4"
DD 6 Hairpin Cotter, 3/32"
EE 10 Hairpin Cotter, 1/8"
FF 1 Spring in, 1/4" x 1"
GG 1 Nylon Tie
HH 1 Spring, Angle Lock
II 9 Spacer, Short
JJ 1 Spacer, Long
KK 2 Trunnion, Lift Rod
4
5
ASSEMBLY OF BLADE TO TRACTOR
6. Assemble one 5/16-24 hex jam nut onto threaded
end of control cable approximately 3/4" from end.
Assemble threaded cable end through round hole
in cable mount bracket and secure with another
5/16-24 hex jam nut. See figure 7.
TO PREPARE TRACTOR:
A. Remove the mower or any other attachment you
may have mounted to your tractor. Mark all loose
parts and save for re-assembly. Refer to tractor
owners manual for instructions on removal of the
mower or attachment.
B. Remove and save both suspension arms, along
with the nuts and washers which fasten them to
the lift link rods. Also remove the 3/8" self-tapping
bolts from each side of the tractor frame as shown
in figure 9. On some tractors the lift link nuts
will be reused to fasten the dozer blade lift
assembly to the lift link rods.
8. Attach cable end fitting and long spacer to right
hand hole in angle stop and channel using 1/4" x
1-1/2" hex bolt and 1/4" Nylock nut. Tighten both
1/4" Nylock nuts that secure the angle stop to the
channel. See figure 8. NOTE: Keep cable and
fitting in alignment with cable mount bracket
when tightening nuts.
6
7
12. Assemble a lift rod trunnion (facing in) to each lift link
rod using either a, b or c:
a. two 7/16-20 hex jam nuts (48" mower decks)
b. a 3/8-16 Nylock nut and the original lock
nut you removed earlier (models before 1995).
c. a 3/8-24 hex jam nut and the original lock nut
you removed earlier (all other models)
The correct nuts will screw on easily. Tighten nuts so
that one thread of rod extends past bottom nut.
CLEVIS PINS
3/8" x 3/4"
3/8" x 1-1/4" BOLTS,
3/8" LOCK WASHERS
& SHORT SPACERS
LIFT PIVOT
PLATE
HAIRPIN COTTER
(SMALL)
FRAME BRACKET
FRONT
LEFT SIDE
SWAY BAR BRACKET
FIGURE 15
10. Assemble a frame bracket to the outside of the
tractor frame under the left foot rest. Use two 3/8"
x 1-1/4" hex bolts, two 3/8" lock washers and four
short spacers. Use two spacers on each bolt,
between the frame bracket and the tractor frame.
Use only one spacer on the rear bolt if it goes
through a sway bar bracket. See figure 15.
11. Assemble the lift pivot plate to the inside of the
frame bracket using two 3/8" x 3/4" clevis pins and
two small hairpin cotters. See figure 15.
8
22. Align two front holes in Support Bracket with holes
in front of foot rest on right side of tractor frame.
Remove any bolts present in holes, but leave all
brackets in place. Attach the Support Bracket using
two 3/8" x 1-1/4" hex bolts and 3/8" Nylock nuts. If
bolts won't fit, use 3/8" x 1" thread forming bolts
without the Nylock nuts. See figure 22.
17. Move attachment lift lever all the way forward and lock
in position. See figure 28 on page 10.
18. Assemble lift arm link over channel rod and insert pivot
shaft end (from R.H. side of tractor) into hole in L.H. lift
pivot plate. Secure lift arm link to channel rod with 1/8"
(large) hairpin cotter. See figure 19.
19. Assemble a frame bracket under the right hand foot
rest of the tractor using two 3/8" x 1-1/4" hex bolts, two
3/8" lock washers and four short spacers. Use two
spacers on each bolt, between the frame bracket
and the tractor frame. See figure 19.
CLEVIS PINS
3/8" x 3/4"
HAIRPIN
COTTER
(SMALL)
HAIRPIN
COTTER
(LARGE) LIFT PIVOT PLATE
LIFT
ASSEMBLY
PIVOT SHAFT
FRAME
BRACKET RIGHT HAND SIDE VIEW
FRONT
FIGURE 21
9
FIGURE 22
3/8" x 1"
HEX BOLTS
SUPPORT
BRACKET
SUPPORT
BRACKET
UP STOP BRACKETUP STOP BRACKET
HAIRPIN
COTTER
HAIRPIN
COTTER
HANDLE
GUIDE
(2) 3/8" x 1"
THREAD FORMING
HEX BOLTS
or
(2) 3/8" x 1-1/4"
HEX BOLTS
AND 3/8"
NYLOCK NUTS
10
Otros manuales para 486.244122
1
Tabla de contenidos
Otros manuales de Accesorios de Craftsman
Craftsman
Craftsman 486.24621 Manual de usuario
Craftsman
Craftsman 316.792490 Manual de usuario
Craftsman
Craftsman 486.24608 Manual de usuario
Craftsman
Craftsman 486.24545 Manual de usuario
Craftsman
Craftsman 320.64180 Manual de usuario
Craftsman
Craftsman 113.29931 Manual de usuario
Craftsman
Craftsman 486.24275 Manual de usuario
Craftsman
Craftsman SP6721 Instrucciones de uso
Craftsman
Craftsman 509398 Manual de usuario
Craftsman
Craftsman Trimmer Products Manual de usuario
Craftsman
Craftsman ROUTER MOUNTING KIT Manual de usuario
Craftsman
Craftsman 315.25790 Manual de usuario
Craftsman
Craftsman 292660 Manual de usuario
Craftsman
Craftsman 509344 Manual de usuario
Craftsman
Craftsman 358.792440 Manual de usuario
Craftsman
Craftsman 509344 Manual de usuario
Craftsman
Craftsman 351.264271 Manual de usuario
Craftsman
Craftsman BACKWALL WITH METAL PEGBOARD Manual de usuario
Craftsman
Craftsman 486.24598 Manual de usuario
Craftsman
Craftsman 486.24218 Manual de usuario
