Craftex CT056 Manual de usuario

OWNER’S MANUAL

CT056 – 6” Jointer

CRAFTEX CT056 6” WOODWORKING JOINTER

INDEX

GENERAL SAFETY INSTRUCTIONS PAGE 3

SPECIFIC SAFETY INSTRUCTIONS PAGE 4

CT056 Features Page 5

Features Illustration Page 6

Unpacking Page 7

Assembly

Mounting the Motor Page 8

Tensioning the Belt Page 8

Power Supply Page 8

Cutter Head Guard Page 8

Fence Adjustment Page 8

Outfeed Table Adjusting Page 9

Knife Adjusting Page 9

Operation

Edge Planing Page 10

Planing Safely Page 10

Rabbeting Page 11

Honing Knives Page 12

Knife Replacement Page 13

Cutter Head Removal Page 14

Schematic Drawings

CT056 Jointer Page 15

Base Page 16

Parts List Page 17

Parts List Continued Page 18

CT056 Accessories Page 19

Warranty Page 20

GENERAL SAFETY INSTRUCTIONS

EXTREME CAUTION SHOULD BE USED IN OPERATING ALL POWER TOOLS. KNOW

YOUR POWER TOOL, BE FAMILIAR WITH ITS OPERATION. READ THE OWNER’S

MANUAL AND PRACTICE SAFE USAGE PROCEDURES AT ALL TIMES.

CONNECT your machine ONLY to the matched and specified power

source.

WEAR SAFETY GLASSES, RESPIRATORS, HEARING PROTECTION

and SAFETY SHOES when operating heavy machinery. Always wear

safety glasses.

DO NOT wear loose clothing or jewellery when operating machinery.

A Safe Environment is important. Keep the area free of dust, dirt and

other debris in the immediate vicinity of the machine.

BE ALERT! Do Not Use prescription or other drugs that may affect

your ability or judgement to safely use this machine.

DISCONNECT the power source when changing drill bits, hollow

chisels or making other adjustments or repairs.

NEVER leave an operating tool unattended.

NEVER reach over the table when the tool is in operation.

ALWAYS keep blades, knives or bits sharp and properly aligned.

ALWAYS keep all safety guards in place and ensure their proper

function.

ALWAYS use push sticks and featherboards to safely feed your work

through the machine.

ALWAYS make sure that any tools used for adjustments are removed

before operating the machine.

ALWAYS secure your work with the appropriate clamps or vises.

ALWAYS keep bystanders safely away while operating machinery.

THINK SAFETY. WORK SAFELY. Never attempt a procedure if it does

not feel safe or comfortable.

CT056 JOINTER

SPECIFIC SAFETY INSTRUCTIONS

Always keep the cutter head knives sharp and free of rust, tar and pitch

Always use push blocks when jointing stock that does not provide a

reasonable distance of safety for your hands.

Never allow your hands to pass directly over the cutter head.

Always make sure that the exposed cutter head behind the fence is

guarded particularly when jointing near the leading edge such as in

rabbetting.

Never perform jointing operations on wood materials shorter than 8”,

narrower than 3/4" or less than 1/4" in thickness.

Do not perform planing operations on wood material shorter than 4”,

narrower than 3/4", wider than 8” or thinner than 1/2".

Maintain the proper relationship of the infeed and outfeed table surfaces

and the cutter head knife path.

Never back your workpiece into the spinning cutter head.

Never make cuts deeper than 1/16”” in a single pass to prevent

overloading the machine and to prevent dangerous kickback.

CT056 6” WOODWORKING JOINTER

FEATURES

As part of the growing line of Craftex woodworking equipment, we

are proud to offer the CT056. The Craftex name guarantees Craft Excellence. By

following the instructions and procedures laid out in this owner’s manual, you

will receive years of excellent service and satisfaction. The CT056 is a

professional tool and like all power tools, proper care and safety procedures

should be adhered to.

Motor – 1HP, 110/220 volt (Pre-wired for 110v) Ball Bearing Motor.

Safety Power Switch with removable key.

Precision-ground, cast-iron tables on an inclined dovetail way.

Precision Gib adjustments.

Precision-ground, center-mounted fence.

Adjustable infeed and outfeed tables.

Steel stand with built-in chip chute and 4” dust port.

Bed size – 7” x 47”.

Fence size – 4” x 29”.

High-speed steel knives – 3.

Cutter-head speed – 5,000 RPM

Table Height – 32”.

Gross Weight – 106 kg.

CT056 6” WOODWORKING JOINTER

ILLUSTRATED FEATURES

CT056 6” WOODWORKING JOINTER

Unpacking

Your Craftex CT056 Woodworking Jointer comes assembled with the exception

of the steel stand, the mounting of the motor and the installation of the knife

guard.

Carefully remove all packing material and recycle where possible.

Cleaning

A protective coating is applied to your CT056 to protect it from corrosion in

shipping. This material should be removed with a cloth and mineral spirits. When

clean and dry, a coat of paste wax

should be applied to the precision

ground surfaces to protect them from

further corrosion.

Assembly

The Dust Chute doubles as a motor

mount and must be fastened to the

front and rear panels with the nuts,

bolts and washers provided. Do not

tighten the fasteners until the entire

base is sitting on a level surface.

Attach the left end panel so that the

dust chute is positioned in the

opening.

Attach the right end panel.

When you are satisfied that the base

is level, tighten all nuts and bolts

securely.

Please refer to page 16 for

numerical order of base

assembly

CT056 6” WOODWORKING JOINTER

Assembly, Continued

Mounting The Motor

Mount the motor on the top of the dust chute with the bolts provided. The bolt

heads should be in the chute.

Carefully place the jointer unit on top of the base and bolt into place. This unit is

heavy and will require assistance to lift

it and position it on top of the base.

When in position, place the drive belt

on the sheave of the motor and the

cutter head sheave.

Tensioning The Drive Belt

The illustration shows the correct way

to install and tension the motor drive

belt. When you are satisfied that the

motor is positioned correctly, securely

tighten the motor mount bolts.

Power Supply

The CT056 is pre-wired at 110 volts and requires a 15-amp circuit. It is

recommended that you use a dedicated circuit for the tool.

Cutter Head Guard

The shaft of the cutter head guard fits into a socket on the side face of the infeed

table. Loosen the locking screw, insert the shaft and tighten the locking screw.

Adjusting The Fence

With the fence in the 90-degree

position, use a combination square to

determine if the fence is accurate.

Should this not be the case, loosen the

fence vertical locking screw lever.

Fine-tune the adjusting bolt until the

fence is vertical.

To adjust the fence in the 45-degree

position, loosen the horizontal locking

screw lever and fine–tune the

adjusting bolt accordingly.

CT056 6” WOODWORKING JOINTER

Assembly, Continued

Adjusting The Outfeed Table

CAUTION: The following operation must

be done with the CT056 Jointer

disconnected from its power source.

For accurate results from your CT056

Jointer, the outfeed table MUST be level

with the cutter head knives at their highest

point. The knives must be parallel to the

outfeed table and project equally from the

cutter head.

To achieve this, loosen the outfeed table lock. Using a straightedge, lay it across

the outfeed table where the cutter head opening is located.

Rotate the cutter head slowly by hand by rotating the drive belt sheave at the

rear of tool. CAUTION: Do not attempt to rotate the cutter head itself as the

knives are extremely sharp.

If all the (3) knives appear to high or too low, rotate the outfeed table height

wheel accordingly. Tighten the outfeed table lock.

The knife edges must just touch the straightedge. If one knife is too high or too

low, the knives must be re-set.

Adjusting Knives

A knife may

be reset by

loosening

the 5 lock

screws on

the cutter

head for that

particular

knife. Set your straightedge over the center of that knife so that the edge of the

knife touches it. Snug the center lock screw. Reposition the straightedge to the

ends of the knife and repeat the procedure. When it is determined that the knife

is parallel through its full length, secure the locking screws.

CT056 6” WOODWORKING JOINTER

Operation

Edge Planing

Prior to starting any jointing operation, it is best to inspect the workpiece to

determine the direction of the wood grain. The best jointing results are gained by

feeding the wood into the knives with the grain.

Adjust the infeed table to remove the minimum amount of stock required by

lowering or raising the infeed table. Loosen the infeed table lock and adjust

accordingly. Securely

lock the table.

Planing Safely

For edge planing grasp your workpiece as shown, being sure to keep fingers well

above the table surface.

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Craftex

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual