Coulisse MOTION CM-08 Manual de usuario
1
1
1
1
1
11
11
1
+
+
11
19
20
21
20.2
20.1 20.2
20.4 20.520.3
20.1
21.1
21.3
21.2
21.4 21.5
MOTION CM-08 LI-ION END MOTOR MOTION CM-08 LI-ION END MOTOR
Hold the program button to manually operate
the blind.The blind will move as long as the
button is being pressed. (max. 15 sec.)
To move the blind in opposite direction, release
the program button and repeat step 19.1.
In case there is no remote control or pull control, the blind can
be operated with the program button on the motor.
Advanced options
The remote starts searching
for blinds (search mode).
This is indicated by the LED’s
flashing from left to right.
To activate
Single select
simultaneously
hold the centre
button and press
the pair button.
To search for
the next blind
press the right
button. Search
mode will be
activated.
To find the
previous blind
press the left
button.
To exit
Single select
press the
right button
during
search
mode.
Once a blind is found the
channel LED will flash
and the blind starts
stepping, indicating that
program mode has been
activated. The blind
can now be (un)paired
to the remote and/or
programmed.
The remote starts
searching for blinds
(search mode). This
is indicated by the
horizontal bars on the
remote.
To activate Single
select simultaneously
hold the centre
button and press the
pair button.
Single select makes it possible to activate program mode on a single blind through a
remote control, without having to physically press the program button on the blind.
To search for
the next blind
press the right
button. Search
mode will be
activated.
To find the
previous blind
press the left
button.
To exit Single
select press
the right
button during
search mode.
The display
shows the
letter O.
Once a blind is found
the channel number
will flash and the
blind starts stepping,
indicating that
program mode has
been activated. The
blind can now be (un)
paired to the remote
and/or programmed.
Single select makes it possible to activate program mode on a single blind through a
remote control, without having to physically press the program button on the blind.
Manual control
Single select 5 channel remote
Single select 15 channel remote
English
1
13 3 3
1
1
3 3 3
1 1 3 3 3
1 1
3
3 3
1 1 3 3 3
+
+
+
23
24
24.1
22.1 22.2
22.3
23.3 23.4 23.5
23.1
22.4 22.5
22
23.2
MOTION CM-08 LI-ION END MOTOR MOTION CM-08 LI-ION END MOTOR
Channel select makes it possible to copy blinds in between channels/remotes without having
to physically press the program button on the motors.
To activate
channel select
simultaneously
hold the channel
selection button
and press the pair
button.
Press the pair
button on the (new)
remote to pair the
blinds to the new
channel.
To exit channel
select go back to the
channel selected at
step 22.1 and repeat
step 22.2
All blinds in the selected
channel will start
stepping, indicating
program mode has been
activated. All blinds
can be copied to a new
channel on the same
remote or other remote.
Select a new channel on
the (new) remote.
Channel select makes it possible to copy blinds in between channels/remotes without having
to physically press the program button on the motors.
Select the channel
you would like to
copy.
To activate
channel select
simultaneously hold
the channel selection
button and press the
pair button.
Press program
button on the (new)
remote to pair the
blinds to the (new)
remote.
To exit channel
select choose
the channel you
selected at step 23.1
and repeat step 23.2
All blinds in the selected
channel will start
stepping, indicating
program mode has been
activated. All blinds
can be copied to a new
channel on the same
remote or to other
remotes. Select a channel
on a (new) remote.
Hold the program button and pull twice to activate or de-activate the motor.
The motor can also be activated by charging it with a micro USB cable.
To prevent the blind from damage the motor has a transport mode that
makes sure the blind will not be activated before installation.
Channel select 5 channel remote
English
Channel select 15 channel remote
Activate / de-activate the motor
Select the channel
from which the
blinds must be
copied.
or
25.2
25.1
25.3
25
26.2
27.1
26.3
26
MOTION CM-08 LI-ION END MOTOR MOTION CM-08 LI-ION END MOTOR
Top-down/bottom-up blinds are powered by two motors: one for the bottom rail
and one for the middle rail. The motors need to be programmed individually: first
the bottom rail motor and then the middle rail motor.
Check the direction of rotation of the bottom
rail (see step 6) and move the bottom rail
to the desired top position. Simultaneously
hold the centre and the down button on the
remote until the blind stops stepping and
starts stepping again. The top position has
been saved
Pair the bottom rail motor to an empty channel
on the remote. (see step 5)
Move the bottom rail to the desired bottom
position. Program the bottom position of the
bottom bar. Simultaneously hold the centre
and the up button on the remote until the blind
stops stepping and starts stepping again.
The bottom position has been saved
Top-down/bottom-up (bottom rail)
Up
Centre
Down
Centre
Top-down/bottom-up blinds are powered by two motors: one for the bottom rail
and one for the middle rail. The motors need to be programmed individually: first
the bottom rail motor and then the middle rail motor.
Check the direction of rotation of the middle
rail (see step 6) and move the bottom rail
to the desired top position. Simultaneously
hold the centre and the down button on the
remote until the blind stops stepping and
starts stepping again. The top position has
been saved
Pair the middle rail motor to an empty channel
on the remote. (see step 5)
Move the middle rail to the desired bottom
position. Program the bottom position of the
bottom bar. Simultaneously hold the centre
and the up button on the remote until the blind
stops stepping and starts stepping again.
The bottom position has been saved
Top-down/bottom-up (middle rail)
Up
Centre
Down
Centre
English
MOTION CM-08 LI-ION END MOTOR MOTION CM-08 LI-ION END MOTOR
Disclaimer:
© Copyright Coulisse
All rights reserved. No part of this publication may be reproduced,
stored in a retrieval system, or transmitted, in any form, by any
means, electronic, mechanical, photocopying, recording, digital or
otherwise without the written permission of the publisher.
Although this manual has been composed with the most
care, Coulisse B.V. does not accept any responsibility for damage
due to mistakes and/or faults in this manual.
Coulisse B.V. reserves the right to revise the manual and to revise
and/or changes its content at any time, without obligation to
notify any person or entity of such revisions or changes.
The most recent version replaces older versions of this manual.
The most recent version is available at my.coulisse.com or
contact your Coulisse contact person.
We invite you to send remarks and comments about this manual
For the latest information and updated
manuals visit rtube.nl/cm-08
English
Problem Cause Solution
Blind does not work.
Motor is in transport mode. Activate the motor. See step 24.
Motor battery is empty. Charge the motor. See step 18.
Remote battery is empty. (LEDS of
remote are flashing rapidly.)
Replace the battery in the remote.
See the manual of the remote.
Remote battery is inserted
incorrectly.
Replace the battery in the remote.
See the manual of the remote.
Radio-frequency interference Make sure that the antenna of the motor
is out of the way from metal objects.
The distance from the remote to
the motor is too far.
Move closer to the motor.
The remote is not connected to
the blind.
Pair the remote to the motor.
See step 6.
Motor LED flashes red. The battery of the motor is empty. Charge the motor. See step 18.
Blind is not charging. Charger is not plugged in or does
not work.
Try a different charger or make sure the
charger is plugged in the outlet.
Multiple blinds respond to a
remote. (Unable to program
a single blind)
Multiple blinds are paired to a single
channel.
Pair the blind to a free channel to program
or use single select to program the blind.
Blind moves in small steps. 1) No end limits are programmed.
2) Direct control is de-activated.
1) Program end limits. See step 7 - 10.
2) Activate direct control. See step 16.
Favourite position can not
be programmed.
No end limits are programmed. Program end limits.
See step 7 - 10.
Blind lowers too far. End limits are programmed incorrect. Reprogram end limits. See step 7- 10.
Blind moves in the opposite
direction.
The direction of rotation has been
set incorrect.
Change the direction of rotation.
See step 6.
The blind keeps moving up
and down. The blind is in program mode. Press the program button on the motor
to exit program mode.
Frequently Asked Questions
Coulisse B.V. Vonderweg 48 7468 DC Enter The Netherlands
t+31 547 85 55 55 f+31 547 85 55 50 e[email protected]
coulisse.com
CM08-U-R2
Coulisse B.V. Vonderweg 48 7468 DC Enter The Netherlands
t+31 547 85 55 55 f+31 547 85 55 50 e[email protected]
coulisse.com
Tabla de contenidos
Otros manuales de Motor de Coulisse
