CORNING LSE Series Manual de usuario

INSTRUCTION MANUAL

Models:

6780-4 -- 120/100V

6781-4 -- 230V EU

6782-4 -- 230V UK

6780-NP – 120/100V

6781-NP – 230V EU

6782-NP – 230V UK

CLS-EQ-99 March 2010, Document 01, Revision 01

CORNINGLSEDIGITAL MICROPLATE AND ORBITAL SHAKERS USER’S MANUAL

TABLE OF CONTENTS Page

1.0. GENERAL DESCRIPTION 3

1.1. DEFINITION 3

1.2. PRINCIPLES OF OPERATION 3

2.0. TECHNICAL FEATURES 3

2.1. CONSTRUCTION 3

2.2. GENERAL SPECIFICATIONS 3

3.0. INSTALLATION 4

3.1. UNPACKING 4

3.2. SELECTING A SUITABLE LOCATION 4

3.3. ATTACHING POWER CORD 4

3.4. ENVIRONMENTAL REQUIREMENTS 4

4.0. PROPER INSTALLATION OF SHAKER PLATFORMS 4

4.1. 6780-4, 6781-4 and 6782-4 MODELS 4

4.2. 6780-NP, 6781-NP and 6782-NP PLATFORM INSTALLATION 5

5.0. OPERATING INSTRUCTIONS 5

5.1. INTRODUCTION 5

5.2. BASIC OPERATION 5

5.3. ADDITIONAL OPERATIONS 8

6.0. GENERAL PRECAUTIONS 8

7.0. TROUBLESHOOTING GUIDE 9

8.0. REGULAR MAINTANCE 9

8.1. CLEANING 9

9.0 WARRANTY 10

10.0 DECLARATION OF CONFORMITY 11

11.0 PRODUCT DISPOSAL 12

CORNINGLSEDIGITAL MICROPLATE AND ORBITAL SHAKERS USER’S MANUAL

1.0. GENERAL DESCRIPTION

1.1. DEFINITION

Corning LSE Digital Microplate and Orbital Shakers are intended for shaking microplates, tubes,

bottles, flasks, dishes and other laboratory vessels. The shakers are driven by asynchronous motors,

which enable silent operation and constant shaking speed independent of the load or power supply

fluctuations.

1.2. PRINCIPLES OF OPERATION

Each shaker device consists of two main components:

- Motor with eccentric mechanism

- Control electronics

The motor drives the shaker’s eccentric mechanics and generates shaking effect.

The electronics control the motor RPM, TIME and keyboard functions.

2.0. TECHNICAL FEATURES

2.1. CONSTRUCTION

The shaker housing is made from a high-grade cold rolled steel plate and painted with a highly

resistant polyurethane lacquer.

2.2. GENERAL SPECIFICATIONS: OPERATION RANGE: 4º C TO 65º C, 85% RH

MODEL 6780-4, 6781-4 and 6782-4

POWER SUPPLY 230V 10% - 50Hz, 115V 10% - 50Hz/60Hz

MOTOR POWER 15W

FUSE 2 x 0.25A, 230V

2 x 1 A, 115V

RPM REGULATION DIGITAL, load independent, from 100 to 1200

(1400 - 115V version) RPM in 10 RPM steps

SHAKER ORBIT 3 mm

TIMER 30 sec – 99 minutes 50 seconds in 10 second steps, under 10

minutes in 1 second steps, timer HOLD function

LOAD max. 0.3 kg

DIMENSIONS W x L x H 170 mm x 275 mm x 130 mm

WEIGHT 4.3 kg

MODEL 6780-NP, 6781-NP and 6782-NP

POWER SUPPLY 230V 10% - 50Hz, 115V 10% - 50Hz/60Hz

MOTOR POWER 15W

FUSE 2 x 0.25A 230V

2 x 1 A 115V

RPM REGULATION DIGITAL, load independent, from 50 to 600 RPM in 10 RPM

steps

SHAKER ORBIT 19 mm

TIMER 30 sec - 99minutes 50 seconds in 10 second steps, under 10

min. in 1 second steps, timer HOLD function

LOAD max. 4 kg

DIMENSIONS W x L x H 255 mm x 312 mm x 130 mm

WEIGHT 7.1 kg

CORNINGLSEDIGITAL MICROPLATE AND ORBITAL SHAKERS USER’S MANUAL

3.0. INSTALLATION

3.1. UNPACKING

Before starting installation, carefully examine the shaker for damage or missing parts.

Open the box and lift the device together with inner packing, out of the box.

Remove the inner packing and check that the shaker has not been visibly damaged during

transportation. Keep the packing material until you are sure that the shaker works properly.

Check information on the rear data label and verify the correct electrical rating:

- Model

- Serial Number

- Electrical rating

Should any kind of damage have occurred during transportation, immediately notify the carrier. The

carrier is responsible for correcting damage caused in shipment.

3.2. SELECTING A SUITABLE LOCATION

When selecting a location for the shaker, please consider following:

Put the device on a smooth, horizontal and stable surface.

Leave enough space around the device for normal air circulation, minimally 10 cm.

Leave enough space around the device, so it can be easily controlled and maintained.

Don’t use the device in surroundings where there are major temperature and humidity

fluctuations. Also avoid locations in direct sun light or places near devices that produce heat.

Avoid locations with excessive vibrations.

3.3. ATTACHING POWER CORD

Fit the main power cord, which is included in the package, into the power receptacle on the shaker.

Connect the other end of the cord to a properly grounded wall outlet. To avoid interference from noise,

surges and spikes, a dedicated line is preferred. If no such line is available, avoid lines to which

powerful electric motors, refrigerators and similar devices are connected.

Take care when you plug the cord to a grounded wall socket. Do not touch

plug with wet hands. Plug the cord to a grounded wall socket only with dry

hand.

3.4. ENVIRONMENTAL REQUIREMENTS

The Corning’s digital shakers have been built for operating in both cold and heated laboratory

environments and in high humidity environments as follows:

At temperatures between 4C and +65C

In humidity up to 85% (without condensation)

4.0. INSTALLATION OF SHAKER PLATFORMS

4.1. MODEL 6780-4, 6781-4 AND 6782-4

Each of these models comes with the platform and 4 screws. Using a screw driver, attach the

platform firmly to the shaker base with the 4 included screws.

CORNINGLSEDIGITAL MICROPLATE AND ORBITAL SHAKERS USER’S MANUAL

4.2. 6780-NP, 6781-NP AND 6782-NP.

The 6780-NP, 6781-NP and 6782-NP model shakers have available a variety of platforms to meet

most shaking needs. These platforms mount to the shakers via four mounting platforms which easily

plug into four rubber mount points on the top of the shaker.

5.0. OPERATING INSTRUCTIONS

5.1. INTRODUCTION

nx10 (RPM) t (min)

RUN TIME RPM

POWER

Push

Time/RPM

1. POWER switch – switches shaker ON (light on) or OFF.

2. RUN green signal light – lit when the shaker is running.

3. TIME yellow signal light – lit when the shaker is set on time.

4. RPM yellow signal light – lit when the shaker is set on rpm.

5. ENCODER – by rotating the encoder right (+) or left (-) you can change the set TIME or

RPM. Push the encoder to switch between TIME and RPM set values.

If you rotate the ENCODER knob quickly then values go up or down on display very

quickly.

6. START/STOP button – press to START or STOP operation.

5.2. BASIC OPERATION

POWER t (min)

nx10 (RPM)

RUN TIME RPM

Push

Time/RPM

Press the POWER switch on the control panel. The Corning Digital shaker automatically

detects supply frequency of 50 Hz or 60Hz, and displays F50 or F60. Then the display

switches to show the set time and illuminates the time light.

CORNINGLSEDIGITAL MICROPLATE AND ORBITAL SHAKERS USER’S MANUAL

POWER t (min)

nx10 (RPM)

RUN TIME RPM

Push

Time/RPM

Time signal light is on. By rotating the encoder right (+) or left (-) the set time can be selected

from 30 sec to 99 min 50 sec : 99.5 99 min 50 sec

9.59 9 min 59 sec

0.30 30 sec

POWER

RPMTIMERUN

nx10 (RPM) t (min)

Push

Time/RPM

If you want to set the timer to hold – turn the knob left or right until HLd is displayed. You can

reach the HLd function by setting to under 0.30 or above 99.5

Push down on the encoder knob to switch modes between time set mode and RPM set mode.

POWER t (min)

nx10 (RPM)

RUN TIME RPM

Push

Time/RPM

RPM signal light is on. By rotating the encoder right (+) or left (-) the desired RPM can be

selected : 34 340 Rpm

120 1200 Rpm

Press START/STOP button to start operation

CORNINGLSEDIGITAL MICROPLATE AND ORBITAL SHAKERS USER’S MANUAL

POWER

RPMTIMERUN

nx10 (RPM) t (min)

Push

Time/RPM

RUN and TIME signal lights on. Shaker runs and counts down time from set value.

NOTE: YOU CANNOT MODIFY THE SET TIME DURING SHAKING, HOWEVER, YOU CAN STOP

THE UNIT WITH THE START/STOP BUTTON AND THEN RESET THE TIME.

POWER t (min)

nx10 (RPM)

RUN TIME RPM

Push

Time/RPM

If you want to change the RPM during shaking, push the encoder knob to put the shaker into

RPM set mode (RPM signal light will be on). Rotate the encoder right (+) or left (-) to set the

desired value. In the meantime, the RPM signal light will flash. When you stop rotating the

encoder knob, the signal light for RPM will stop flashing after 2 seconds.

POWER t (min)

nx10 (RPM)

RUN TIME RPM

Push

Time/RPM

When the run time has elapsed or when you press the START/STOP button, the display will

show “End” and the RUN light will flash. When shaker completely stops the set speed and

time will return to the last programmed values.

CORNINGLSEDIGITAL MICROPLATE AND ORBITAL SHAKERS USER’S MANUAL

5.3. ADDITIONAL OPERATIONS

POWER nx10 (RPM) t (min)

RUN TIME RPM

Push

Time/RPM

Rotate the encoder knob ONE CLICK right (+) or left (-) to view the set value for RPM during

the shaking. The RPM signal light will then flash for 2 seconds and the display will show the

set RPM. The RPM and the light will stop flashing after 2 seconds.

NOTE: Shaker must be in RPM mode – RPM signal light must be on.

POWER

RPMTIMERUN

nx10 (RPM) t (min)

Push

Time/RPM

Rotate the encoder knob ONE CLICK right (+) or left (-) to view the set value for TIME during

the shaking. The TIME signal will light for 2 seconds and the display will show the set TIME.

After 2 seconds the display will return to the count TIME and the signal light will stop flashing.

NOTE: Shaker must be in TIME mode – TIME signal light must be on.

6.0. GENERAL PRECAUTIONS

Always plug the unit into a properly grounded and fused outlet.

Do not use the device near water sources. Take care, that water will not fall on the device,

especially during cleaning procedures.

Do not use device in a caustic or explosive atmosphere.

There are no user serviceable parts in the unit. Opening the unit may void the warranty. In

case of a malfunction or liquid being spilled into the unit, unplug the device from its power

outlet and contact Corning Customer Service.

NOTE:

If the device does not function properly, even if you have exactly followed the instructions

described in the User’s manual, contact Corning Customer Service at:

1.800.492.1110 (for toll-free calling withing the U.S. and Canada)

1.978.442.2200 (outside the U.S.), or

contact your local Corning support office listed in the back of this manual.

If the equipment is used in a manner not specified by this manual, the equipment may become

unsafe to operate, could harm the user or the device, and may void the warranty.

CORNINGLSEDIGITAL MICROPLATE AND ORBITAL SHAKERS USER’S MANUAL

Do not shake flammable or explosive samples or use the unit in a flammable or

explosive environment.

7.0. TROUBLESHOOTING GUIDE

Problem Explanation / Solution

POWER key does not light Check the power source

Check fuses

Shaker stalls – Message Er1 Power unit down, then restart

Display does not light

Message Er2 on display

Message Er3 on display

Message Er4 on display

Contact Corning Customer Service

8.0. REGULAR MAINTENANCE

With the exception of the occasional maintenance described in 4.0 of this manual, no

scheduled maintenance is normally required. However, an experienced technician should

regularly check the device operation at least once a year to make sure it is operating correctly.

Regular cleaning of the housing is recommended.

8.1. CLEANING

The housing of the Shaker Unit can be cleaned with special cleaners for polyurethane (plastic)

surfaces. A damp (not wet) cloth is recommended.

NOTE:

Do not use any corrosive or abrasive cleaners (acetone, polish, etc.) because the shaker

surface can be permanently damaged.

Before cleaning the device, unplug main cord from wall socket.

9.0. WARRANTY STATEMENT

CORNINGLSEDIGITAL MICROPLATE AND ORBITAL SHAKERS USER’S MANUAL

Corning Incorporated (Corning) warrants that this product will be free from defects in material and

workmanship for a period of two (2) years from date of purchase. CORNING DISCLAIMS ALL OTHER

WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES

OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE. Corning’s sole

obligation shall be to repair or replace, at its option, any product or part thereof that proves defective in

material or workmanship within the warranty period, provided the purchaser notifies Corning of any

such defect. Corning is not liable for any incidental or consequential damages, commercial loss or any

other damages from the use of this product.

This warranty is valid only if the product is used for its intended purpose and within the guidelines

specified in the supplied instruction manual. This warranty does not cover damage caused by

accident, neglect, misuse, improper service, natural forces or other causes not arising from defects in

original material or workmanship. This warranty does not cover motor brushes, fuses, light bulbs,

batteries or damage to paint or finish. Claims for transit damage should be filed with the

transportation carrier.

In the event this product fails within the specified period of time because of a defect in material or -

workmanship, contact Corning’s Customer Service at the following numbers: USA: 1-800-492-1110;

Canada: 1-978-442-2200. For other regions of the world, please visit www.corning.com/lifesciences

or see the included instruction manual for a list of World Wide Support Offices.

Corning’s Customer Service team will help arrange local service where available or coordinate a

return authorization number and shipping instructions. Products received without proper authorization

will be returned. All items returned for service should be sent postage prepaid in the original

packaging or other suitable carton, padded to avoid damage. Corning will not be responsible for

damage incurred by improper packaging. Corning may elect for onsite service for larger equipment.

Some states do not allow limitation on the length of implied warranties or the exclusion or limitation of

incidental or consequential damages. This warranty gives you specific legal rights. You may have

other rights which vary from state to state.

No individual may accept for, or on behalf of Corning, any other obligation of liability, or extend the

period of this warranty.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de laboratorio de CORNING

CORNING

CORNING Lambda EliteTouch Manual de usuario

CORNING

CORNING LSE 6780-FP Manual de usuario

CORNING

CORNING Spin-X UF 500 Manual de instrucciones

CORNING

CORNING Stripettor 4998 Manual de usuario

CORNING

CORNING LSE 6703 Manual de usuario

CORNING

CORNING LSE 6783 Manual de usuario

CORNING

CORNING PC-400D Manual de usuario

CORNING

CORNING MicroDEN Manual de usuario

CORNING

CORNING SCF-1296 Manual de usuario

CORNING

CORNING LSE 6775 Manual de usuario

CORNING

CORNING Matribot Bioprinter Manual de usuario

CORNING

CORNING Axygen Axypet Pro Manual de usuario

CORNING

CORNING LSE 6785-SB Manual de usuario

CORNING

CORNING Matribot Bioprinter Manual de usuario

CORNING

CORNING Gosselin S-Blender 1 Hoja de información del producto

CORNING

CORNING Lambda EliteMax Manual de usuario

CORNING

CORNING LSE Manual de usuario

CORNING

CORNING Lambda EliteMax Manual de usuario

CORNING

CORNING OptiTect Manual de usuario

CORNING

CORNING LSE 6875-SB Manual de usuario

CORNING

CORNING LSE 6783 Manual de usuario

CORNING

CORNING AXYGEN AxySpin R Manual de usuario

CORNING

CORNING LSE 6780-4 Manual de usuario

CORNING

CORNING Lambda EliteMax Manual de usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario