Corbin Russwin ASSA ABLOY Access800 Manual de usuario

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

ASSA ABLOY

Installation Instructions

Mortise Lockset

For ML20800 TCAC2 Series

Please read these instructions carefully to prevent missing important steps.

Please Note: Improper installation may result in damage to the lock and void the factory warranty.

Important: The accuracy of the door preparation is critical for proper functioning and security of this lock.

Misalignment can cause premature wear and a lessening of security.

FM224 10/18

For installation assistance contact Corbin Russwin Inc., at 1-800-810-WIRE (9473)

C A U T I O N

DOOR MUST REMAIN OPEN

DURING INSTALLATION.

USE DOOR STOP.

1 2 3

*TEST

FOR PROPER

OPERATION

BEFORE

CLOSING

DOOR

Access 800

ASSA ABLOY

Attention Installer

In U.S.:

Corbin Russwin, Inc.

225 Episcopal Road

Berlin, CT 06037 USA

www.corbinrusswin.com

In Canada:

ASSA ABLOY Door Security Solutions Canada

160 Four Valley Drive

Vaughan, Ontario, Canada L4K4T9

www.assaabloy.ca

WARNING

This product can expose

you to lead which is

known to the state of

California to cause cancer

and birth defects or other

reproductive harm. For

more information go to

www.P65warnings.ca.gov.

08/2018

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

ASSA ABLOY

1) Warning

2) General Description/Speciﬁcations/Features

3) ML20800 TCAC2 Series Product Illustration

4) Installation Instructions 5-12

5) Installation of RF Technology Lock 13

6) Operational Check 14

Table of Contents

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that the interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected

• Consult the dealer or an experienced TV technician for help

This Class B digital apparatus complies with Canadian ICES-003.

Warning: To comply with “Fire Listed” doors, only alkaline batteries must be used.

Changes or modiﬁcations to this unit not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.

1) Warning

7.1) Important 15

7.2) Installation Notes 15

7.3) Electrolynx Connector System 15

7.4) ML20800 TCAC2 Series Illustration with M861 Harness 16

7.5) M861 Forced Door Propped Door Option 17

7.6) M35 Power/Remote Unlocking 18

7) ML20800 TCAC2 Hard Wiring Instructions for Mortise 15

7.7) M35 Power/Remote Unlocking with M861 Forced

Door Propped Door Option

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

ASSA ABLOY

General Description

The Access 800 Mortise Lock is designed for areas which require stand-alone authorized entry.

It is a self-contained microprocessor-controlled keypad with non-volatile memory. The keypad

will hold a total of 100 (M800) or 2000 (M801, M802, M803, M804, M805, M806) different user

codes. User codes “01”, “02” and “03” are utilized for Master, Emergency and Supervisory

Codes respectively. This product is operated by six (6) “AA” alkaline batteries. Corbin Russwin

locks are designed with quality components to provide high security, performance and

durability.

Speciﬁcations

• Latch - Stainless steel • Locking side controlled by any combination of

• Deadbolt - Stainless steel keypad, proximity RF technology or key overide

• Auxiliary Latch - Stainless steel, non handed • Non-locking side retracts latch and deadbolt

• Handed - Easily ﬁeld reversible without • Locks furnished for 1-3/4" doors. Can be

disassembling the lock body furnished for other door sizes upon request.

• Case - 12 gauge heavy duty wrought steel Consult factory

• U.L. Listed (3 hr.)

Features

• Low battery alert–4 chirps after standard • Operates utilizing any two to six digits per

user code entry code. Digits may be repeated and codes

• External remote “request to enter” connector may start with zero.

• Master, Emergency or Supervisory code will • Entry of a programmable number of wrong

unlock door when low battery has expired User Codes disables all codes for a

• Programming done at the keypad (Except programmable number of seconds

M802 & M805) or with a PDA using Yellow LED on solid

Accessware™ with Access HH application

Software.

• M800 allows last 15 transactions to be

• M801 - M806 allows last 2000 transactions

to be output to a PC via a PDA and

Accessware™ software

2) General Descriptions/ Speciﬁcations/ Features

output to portable printer via infrared link

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

ASSA ABLOY

3) ML20800 TCAC2 Series Product Illustration

ASSA ABL

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

ASSA ABLOY

Verify hand and bevel of door. Illustrations shown are as viewed from the outside

or secure side of opening.

4) Installation Instructions

2Prep door according to supplied door marker.

FOR

USE

FIRE

DOOR

NOT

Left Hand

Hinges Left.

Open Inward.

"LH"

Left Hand

Reverse Bevel

Hinges Left.

Open Outward

"LHR"

Right Hand

Hinges Right.

Open Inward.

"RH"

Right Hand

Reverse Bevel

Hinges Right.

Open Outward

"RHR"

7/8"

1-1/2

1/8" Dia. holes

(2) required

Slot

Attach ﬁre stop plate

using self tapping screws

#8-32 x 1/2 long for wood &

metal doors

.C of 1-1/2 Dia

Outside

of Door

Hole for ribbon cable

Non Fire Rated Exterior Doors

install weather conduit.

(Hollow Doors Only)

Outside

of Door

Non Fire Rated Door

Hole for

ribbon cable

Install conduit half with recessed

panel "Not For Use On Fire Door"

visible from outside of door.

The optional conduit is available

for non ﬁre rated doors to provide

weather protection for exterior door

applications. It is included in the M99

Weatherseal Gasketing Kit when

ordered with the device. If ordered

separately, order part number

794F929.

Fire stop plate required

for ﬁre rated doors

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

ASSA ABLOY

RED Locking Screw

Catch Plate

Handing of Lock Body

Step 1) Move the red locking screw to

side of lock body being locked (Fig. 1)

Step 2) Push in latch then depress catch

plate with screw driver (Fig. 1)

Step 3) Pull latch out of lock body

and turn latch over (Fig. 2)

Figure 1

Figure 2

Figure 3

Figure 5

Step 4) Push in latch while holding

screw driver behind latch tail (Fig. 3)

Note: Push in latch until catch plate is

no longer depressed (Fig. 4)

Step 5) Rotate lock front to match

bevel of door as shown (Fig. 5)

MAKE SURE CATCH PLATE IS

EVEN W/TOP SURFACE

GOOD BAD

Figure 4

WARNING:

LOCK-IN CAN

OCCUR IF LATCH

IS NOT PROPERLY

INSTALLED

4) Installation Instructions

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

ASSA ABLOY

Lock Assembly Instructions

Align bevel accordingly. Engage 7/64 Allen wrench onto cap screw required for Step 5:3 on page 8.

Feed connector and wires through non cylinder side of door. Insert lock body into mortise cutout in door

and hold loosely in place with (2) #12x1" lock body screws.

(2) #12x1"

Combination Screws

Feed conn s

through non-cyl r side

Lock Body

7/64 Allen Wrench

Inside

of Door

ector & wire

inde

4) Installation Instructions

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

ASSA ABLOY

Spindles

Keypad Ribbon Cable

Outside

of Door

Installation of Outside Escutcheon

Ground

Wire

Gasket (optional)

C A U T I O N

DOOR MUST REMAIN OPEN

DURING INSTALLATION.

USE DOOR STOP.

NOTE: Key and

cylinder must be

rotated as shown

Correct Incorrect

1. For exterior applications, an optional M99 Weatherseal Gasketing Kit can be ordered when a

device is ordered. This kit includes gaskets and a conduit. When ordering the kit separately, order

part number 794F929. The gaskets may be used as a seal between the escutcheon and the door

surfaces.

2A. For ﬁre rated doors, feed ribbon cable connector and ground wire from outside escutcheon through

the ﬁre stop plate.

2B. For non-ﬁre rated doors, feed ribbon cable connector and ground wire from outside escutcheon

through weather seal gasket (if used), then conduit sleeve in door (not shown).

3. With outside lever horizontal, insert mounting posts into the door. Make certain the lever spindle is

properly engaged in lock. (see diagram and Note A. below) Screw cylinder into mortise lock,

ensuring the cylinder orientation is in the correct position (see diagram below) . Using the 7/64 allen

wrench provided, hand tighten (5-10 in. lbs.) the cap screw to prevent unscrewing of the cylinder.

Turn the key to make certain that the locking mechanism (latch, deadbolt, key) functions correctly.

Tighten (2) #12 x 1" lock body screws. Remove allen wrench.

NOTE A.

For MUSÉO Lever

collections ONLY.

Thread hub into lever

and fully tighten.

Align adapter hub

with square hole in

lever, keeping hub

as tight as possible.

Use Correct Spindle Orientation

STANDARD MUSÉO

Lever

GASKET APPLICATION:

Peel off the adhesive protective paper

from gasket. Feed Trim assembly motor

harness through gasket opening as

shown and ﬁrmly press gasket to

escutcheon, aligning edge of gasket

with the edge of the escutcheon.

ASSA ABLOY

ASSA ABL

4) Installation Instructions

ASSA ABL

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

ASSA ABLOY

Keypad Ribbon

Cable

Locate (3) oval head screws

and insert through the

escutcheon and thread

into the outside escutcheon.

Ground

Wire

Thumb Turn

Micro Switch

Installation of Inside Escutcheon

NOTE: Connectors go on only one way. Do not offset connector and be sure they are completely seated.

1. Connect ground wire to ground terminal, keypad ribbon cable connector to controller, and lock body

harness to motor connector. If you have a thumb turn, connect the male thumb turn switch connector

to the female thumb turn switch connector.

2. Align thumb turn to the vertical position.

3. Feed excess lock body harness wire back into the mortise of the door between the door cavity and

lock body, making sure no excess wire enters the cylinder hole of the lock body. (see diagram page 8)

Push excess keypad ribbon cable into the ribbon cable hole.

NOTE: For RF Technology versions refer to Section 5 to install through bolt screws.

Controller

Female Thumb Turn

Switch Connector

Male Thumb Turn

Switch Connector

Thumb Turn

C A U T I O N

DOOR MUST REMAIN OPEN

DURING INSTALLATION.

USE DOOR STOP.

Thumb Turn Male Switch

Connector - for non

thumb turn mortise locks

the thumb turn male

switch connector may

be placed in the space

below the controller and

remain disconnected

Motor Connector

Ground Terminal

Red & Black

Wires

Keypad Harness (ribbon cable)

Remote Power

Connector

(M35 Remote Power

Wiring Harness also

available as part

No. 793F069)

Lock Body Harness

Lock Body

Harness

Gasket

GASKET APPLICATION:

Peel off the adhesive protective paper

from gasket. Feed Trim assembly motor

harness through gasket opening as shown

and ﬁrmly press gasket to escutcheon,

aligning edge of gasket with the edge of

the escutcheon.

Inside

of door

4) Installation Instructions

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

ASSA ABLOY

6Installation of Inside Escutcheon (continued)

CAUTION: Do not allow lock body harness wires to enter cylinder hole in lock body. Wire

damage and/or malfunction of the lock may occur.

1. Turn inside lever to the horizontal position and rotate the thumb turn to the vertical position. Slide onto

spindle halfway. With inside escutcheon resting on spindle, be certain that all keypad ribbon cable will

remain inside ribbon cable hole, and that ground wire will not get pinched once escutcheon is

mounted. Escutcheon will not ﬁt ﬂush on door otherwise.

2. Insert 3 #10-24 screws through inside escutcheon and thread loosely into outside escutcheon. Check

operation of both inside and outside levers and make sure the thumb turn and key still operate the

latch and deadbolt correctly. If lock function is satisfactory, fully tighten the bottom two screws. Check

operation of both levers again. If levers move freely, tighten top screw. If levers do not move freely,

loosen bottom screws and realign the escutcheons until proper operation is obtained.

Inside

of door

Lock Body Harness - Feed excess

wire back into the mortise of the

door between the door cavity and

lock body. Do not feed excess

wires into the cylinder hole of

the lock.

4) Installation Instructions

Tabla de contenidos

Otros manuales de Cerrar de Corbin Russwin

Corbin Russwin

Corbin Russwin ASSA ABLOY MP9800 Series Manual de usuario

Corbin Russwin

Corbin Russwin ASSA ABLOY SN Series Manual de usuario

Corbin Russwin

Corbin Russwin CL3550 Manual de usuario

Corbin Russwin

Corbin Russwin ED4800 Series Manual de usuario

Corbin Russwin

Corbin Russwin Access 800 Manual de usuario

Corbin Russwin

Corbin Russwin Access 800 Manual de usuario

Corbin Russwin

Corbin Russwin CL3300 Series Manual de usuario

Corbin Russwin

Corbin Russwin CL3300 Series Manual de usuario

Corbin Russwin

Corbin Russwin ASSA ABLOY Museo MP6600 Series Manual de usuario

Corbin Russwin

Corbin Russwin CL33600 Manual de usuario

Corbin Russwin

Corbin Russwin Rim & SecureBolt ED4200 series Manual de usuario

Manuales populares de Cerrar de otras marcas

Magic

Magic 105 Manual de usuario

Gantner

Gantner GAT NET.Lock 7020 System Guía rápida

Wittkopp

Wittkopp Insys 7202 Manual de usuario

Dorma

Dorma Studio Classic Manual de usuario

Securam

Securam ECSL-601 Manual de usuario

Sudhaus

Sudhaus 3003 Manual de usuario

Safety 1st

Safety 1st 48517 Manual de usuario

Pado

Pado FDS-10 Manual de usuario

Esco

Esco systeQ Series Manual de usuario

COMPX

COMPX National D8951 Manual de usuario

secureo

secureo Key Box Manual de usuario

Stock Loks

Stock Loks C8713 Manual de usuario

COMPX

COMPX 1T-058 Manual del propietario

Auslock

Auslock T11 Manual de usuario

ELCOM

ELCOM 7205 Manual de usuario

Stealth SAFES

Stealth SAFES ShadowVault Manual de usuario

Knox

Knox KeySecure 5 Manual de usuario

Kwikset

Kwikset 48334/01 Manual de usuario