Cooledge FABRICOLOR Manual de usuario

EXT-0091-R00-02262020 (LTR) 1/22

Cooledge FABRIColor is a simple, out-of-the-box

way to incorporate the unique look and feel of a

stretch fabric ceiling into your space. Create a canopy

of light in T-bar grid ceilings by adding skylights to

provide immersive illumination that delivers the

visual, biological, and emotional beneﬁts of large

luminous surfaces.

Grid (T-Bar) luminaires deliver immersive illumination for:

• Oces

• Healthcare facilities

• Meeting rooms

• Educational buildings

Features Cooledge’s unique “Inﬁnity Edge” design

for uniform illumination from edge to edge.

1. COMPONENTS

Suspension Cable

Cable Gripper

Hanger Bracket

Control Module

Power and Control Tray

Power Supply

Trim Clip

Trim

Corner

Trim

O +1 604 273 2665

F +1 604 273 2660

T +1 844 455 4448

W cooledgelighting.com

Cooledge Lighting Inc.

110-13551 Commerce Parkway

Richmond, BC V6V 2L1 Canada

Cooledge Lighting reserves the right to change

materials or modify the design of its product

without notiﬁcation as part of the company’s

continuing product improvement program.

COOLEDGE LUMINOUS CEILINGS

FABRICOLOR - GRID (T-BAR)

INSTALLATION GUIDE

5 Year Limited Warranty:

Parts and workmanship

EXT-0091-R00-02262020 (LTR) 2/22

2. TOOLS

CAUTION: Observe precautions for handling electrostatic sensitive devices.

WARNING: Wear clean cotton or latex gloves when handling Cooledge FABRIColor.

Do not remove the plastic protective ﬁlm until the point noted in this install guide.

CAUTION: Use appropriate Personal Protective Equipment (PPE) to ensure safety at work.

Measuring Tape

Level

#2 Phillips Screwdriver 3mm Flat Head Screwdriver 2x wrenches (only required

for threaded rod mounting)

Saw Horses

4mm and 5mm Hex Key

Gloves

Cable Cutters

EXT-0091-R00-02262020 (LTR) 3/22

NOTE: Leave protective

plastic ﬁlm attached

3.1. REMOVE THE CEILING TILES AND ANY CROSS TEES TO GIVE CORRECT CEILING OPENING

3.2. UNPACK LUMINAIRE AND PLACE FACE DOWN ON SAW HORSES AT CORNERS

3.3. ATTACH POWER AND CONTROL TRAY(S) TO STIFFENERS

WARNING: Do not cut or remove any main beam tees. If this is required to make the correct opening size for the luminaire,

consult a ceiling contractor.

3. INSTALLATION PROCEDURE

NOTE: Lift luminaire

using handles provided

NOTE: Power Supply and

Control Module may vary

NOTE: Trays may be mounted remotely. In this case, the DC power connections should be made to the Luminaire (section 3.4) with

a suitable length of cable.

Refer to Section 8. APPENDIX – DMX CONTROL for setting up the control module.

NOTE: Ensure T-nuts rotate fully

inside channel to tighten correctly

EXT-0091-R00-02262020 (LTR) 4/22

8.7”

2.6”

1.4”

Black +

Red -

N/C

Green -

N/C

Blue -

N/C

White -

PSU

24V: 100/200/400

Control Module

5-conductor cable

to luminaire

Red

Green

Blue

White

Black

VIN

58V

DIM (-)

DIM (+)

VIN

RED (+)

58V

BLACK (-)

To power

supply

To Controls

{Starter Cable

Do Not

Connect

Do Not

Connect

DO NOT

CONNECT

DO NOT

CONNECT

DO NOT

CONNECT

DO NOT

CONNECT

NOTE: The power and control tray type will vary depending on region and luminaire size.

3.4. CONNECT POWER AND CONTROL TRAY TO LUMINAIRE

NOTE: Lift luminaire

using handles provided

3.5. ESTABLISH THE REQUIRED POSITIONS FOR SUSPENSION CABLES

Either measure between the suspension points or refer to TABLE 1, PAGE 10.

EXT-0091-R00-02262020 (LTR) 5/22

3.6. ATTACH CABLES TO CEILING ANCHOR POINTS AT REQUIRED POSITIONS

3.7. ATTACH CABLES TO HANGER BRACKETS WITH GRIPPERS

EXT-0091-R00-02262020 (LTR) 6/22

3.8. RAISE LUMINAIRE TO JUST BELOW CEILING LEVEL

3.9. CONNECT THE ELECTRICAL POWER

The electrical power connections should be made by a qualiﬁed electrician in accordance with all national and local electrical and

construction codes.

Refer to Section 8. APPENDIX – DMX CONTROL for setting up the control module.

Leave space for electrician to make connection to power supply.

Connect AC to Power Supply

NOTE: Power Supply and

Control Module may vary

EXT-0091-R00-02262020 (LTR) 7/22

3.11. ATTACH TRIM WITH PROVIDED CLIPS

3.10. REMOVE THE PROTECTIVE PLASTIC WRAPPING AND LIFTING HANDLES

Remove the lifting handles using a 4mm Hex Key.

Ensure you wear gloves from this point forward to prevent marks on the fabric.

3.12. ATTACH CORNER COVER TO TRIM

EXT-0091-R00-02262020 (LTR) 8/22

3.13. LIFT LUMINAIRE INTO FINAL POSITION

Access the cable grippers through adjacent ceiling grid opening and lift the luminaire until the trim is ﬂush with the underside of the

ceiling grid.

WARNING: Overtightening the cables may lift the ceiling grid and cause damage to the luminaire.

CEILING TILE

CEILING GRID

TRIM PIECE FLUSH WITH

UNDERSIDE OF GRID

EXT-0091-R00-02262020 (LTR) 9/22

In general, Cooledge FABRIColor require little or no maintenance; however, if there is a need to handle or clean the luminaires,

Cooledge recommends the following procedures.

Handling:

• Always handle the luminaire from the sides and avoid touching the diuser to prevent ﬁngerprints, oil, or dirt from marking the fabric.

• Always use cloth gloves if handling the fabric diuser.

Cleaning:

Fabric Diuser

Over time there may be some accumulation of dust from the environment. To remove dust there are several methods available including:

• Brush gently with a clean, micro ﬁber cloth or “magic eraser” (if available in your region)

• Vacuum with a clean brush-tip vacuum nozzle

• Blow with compressed air (ensure there is no oil or grease)

• Use an adhesive lint-roller (recommended to test a small area in case the speciﬁc type of roller leaves a residue)

For minor stains, spots or streaks, Cooledge recommends gently wiping the fabric with isopropyl alcohol, “IPA”, (99% or higher) applied

to a clean, soft cloth and allow to dry.

Note: use of liquids other than IPA to clean the fabric diuser may result in permanent stains. FABRICated Luminaires are rated for

dry locations only and should not be exposed to moisture or direct contact with water.

Trim/Fascia

• Wipe trim with a clean, soft cloth

4. HANDLING & MAINTENANCE

EXT-0091-R00-02262020 (LTR) 10/22

5.1. CABLE ATTACHMENT POINTS

5. APPENDIX – POSITIONS OF SUSPENSION POINTS

TABLE 1

NOMINAL SIZE # SUSPENSION POINTS DIM “X” DIM “Y”

4’ X 4’ 420 ⁄” 22 ⁄”

4’ X 6’ 4 21 ⁄” 22 ⁄”

4’ X 8’ 4 26 ⁄” 22 ⁄”

1200mm X 1200mm 4 525mm 550mm

1200mm X 1800mm 4550mm 550mm

1200mm X 2400mm 4655mm 550mm

Otros manuales de Equipo de iluminación de Cooledge

Cooledge

Cooledge TILE TUNABLE WHITE Manual de usuario

Cooledge

Cooledge TILE TNW EXTERIOR R3 Manual de usuario

Cooledge

Cooledge CTR-SCT-DMX-58V Manual de usuario

Cooledge

Cooledge TILE Exterior R2 Manual de usuario

Cooledge

Cooledge TILE GEN2 Manual de usuario

Cooledge

Cooledge 0-10V CONTROL Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario